scholarly journals Compressive Strength Study on the Freeze-thaw Resistance of Recycled Aggregate Concrete Members

2017 ◽  
Vol 11 (1) ◽  
pp. 270-280 ◽  
Author(s):  
Haicheng Niu ◽  
Yonggui Wang ◽  
Xianggang Zhang ◽  
Xiaojing Yin
Keyword(s):  
Compressive Strength ◽  
Mass Loss ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Fine Aggregate ◽  
Replacement Rate ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Surface Scaling

Introduction: Freeze-thaw resistance of recycled aggregate concrete with partial or total replacement of recycled aggregate compared with that of natural aggregate concrete was investigated in this paper. Method: Ninety specimens were fabricated to study the influence of different recycled aggregate replacement ratios on the surface scaling, mass loss, and residual compressive strength after 100 freeze-thaw cycles. Results: The experiment results indicate that the type of recycled aggregate and its replacement ratio have significant effects on the freeze-thaw performance. The cubic compressive strength of recycled aggregate concrete is overall slightly lower than that of normal concrete. After 100 freeze-thaw cycles, the compressive strength decreases and the reduction extent increases with increasing replacement rate of recycled aggregate. The surface scaling of reinforced recycled concrete prisms tends to be more severe with the increase of freeze-thaw cycles. Conclusion: Furthermore, a notable rise in mass loss and the bearing capacity loss is also found as the substitution ratio increases. Under the same replacement rate, recycled fine aggregate causes more negative effects on the freeze-thaw resistance than recycled coarse aggregate.

The Comparison of Properties of Fine Recycled Aggregate Concrete from Different Sources of Recycled Aggregate

2018 ◽  
Vol 760 ◽  
pp. 176-183 ◽  
Author(s):  
Tereza Pavlů
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Concrete Properties ◽  
Different Sources

The main aim of this contribution is comparison the properties of fine aggregate concrete with partial replacement of sand by fine recycled aggregate. The fine recycled aggregate originated from two different sources. The main topic of this article is the study of influence of the origin of FRA to fine aggregate concrete properties. The compressive strength, flexural strength and freeze-thaw resistance were tested. The mechanical properties and weight were examined after 28 and 60 days and after 25, 50, 75 and 100 cycles of freeze-thaw. Partial replacement of sand was 25 and 50 % for all these tests. The properties were investigated by using prismatic specimens.

scholarly journals Compressive Strength of Concrete with Recycled Concrete Aggregate as Coarse Aggregate and Recycled Paving Block Aggregate as Fine Aggregate Partially Substituted by Recycled Brick Aggregate

2020 ◽  
Vol 8 (1) ◽  
Author(s):  
Idi Priyono ◽  
Meiske Widyarti, Erizal
Keyword(s):  
Compressive Strength ◽  
Residential Buildings ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Aggregate Concrete ◽  
Concrete Mix

An excessive extraction of natural resources for aggregate in concrete mix can caused an environmental degradation.  According to Indonesia ministry of industry in 2017, the use of cement is predicted will reach 84,96 million tons, that can affected the use of aggregate for concrete mix are quadruplet to 250 – 350 million tons. Opimally, the use of recycled material is green method that can reduce an excessive extraction of natural aggregates and keep an environmental sustain. The aim of this study is to obtain recycled aggregate concrete compressive strength and examine recycled aggregate concrete quality in days 3, 7, 28, 35, and 90 along with a proposal of the use of recycled aggregate concrete as a building construction material. This research used experimental method of SNI 03-2834-2002 the standard of normal concrete mix design for f’c 25 MPa then built five types of concrete mix of REC B, REC C, REC D, REC E, and REC F with every types of concrete has four sample are used for compressive strength test. The fine recycled paving block aggregate (RPA) were used partially to substituted a fine recycled brick aggregate (RBA) at 0%, 25%, 50%, 75%, and 100% by weigth. The result of this study showed the mixed concrete REC D with RCA 100%, RPA 50% and RBA 50% in 28 days is generate highest compressive strength than other recycle aggregates concrete mixes. Compressive strength at 28 days in a mix codes REC B, REC C, REC D, REC E and REC F are 18,12 MPa; 18,36 MPa; 19,35 MPa;16,69 MPa; and 16,39 MPa. The results show that it is feasible to replace a natural aggregate entirely by recycled aggregates. With compressive strength over 17 MPa at 28 days, mix codes REC B, REC C and REC D are recommended to use the recycled aggregate concrete for structure of residential buildings but mix codes REC E and REC F aren’t recommended and only allowed for non-structural concrete such as separate wall (SNI 8140:2016). Based on SNI 03-0691-1996 about solid brick concrete (paving block), recycle aggregate concrete with mix code of REC B, REC C, and REC D are able to use on paving block with B quality such as parking lot. While, recycled aggregate concrete with mix code of REC E and REC F are able to use on paving block with C and D quality which used for pedestrian, garden and other use. 

Recycling of Waste Concrete and Fly Ash for Recycled Aggregate Concrete: Fundamental Characteristics Evaluation

2009 ◽  
Vol 620-622 ◽  
pp. 255-258 ◽  
Author(s):  
Cheol Woo Park
Keyword(s):  
Fly Ash ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Experimental Program ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Recycled Concrete Aggregate ◽  
Aggregate Concrete ◽  
Waste Concrete

As the amount of waste concrete has been increased and recycling technique advances, this study investigates the applicability of recycled concrete aggregate for concrete structures. In addition fly ash, the industrial by-product, was considered in the concrete mix. Experimental program performed compressive strength and chloride penetration resistance tests with various replacement levels of fine recycled concrete aggregate and fly ash. In most case, the design strength, 40MPa, was obtained. It was known that the replacement of the fine aggregate with fine RCA may have greater influence on the strength development rather than the addition of fly ash. It is recommended that when complete coarse aggregate is replaced with RCA the fine RCA replacement should be less than 60%. The recycled aggregate concrete can achieve sufficient resistance to the chloride ion penetration and the resistance can be more effectively controlled by adding fly ash. It I finally conclude that the recycled concrete aggregate can be successfully used in the construction field and the recycling rate of waste concrete and flay ash should be increased without causing significant engineering problems.

Experimental Study on Compressive Strength of Recycled Aggregate Concrete with Different Replacement Ratios

2012 ◽  
Vol 174-177 ◽  
pp. 1277-1280 ◽  
Author(s):  
Hai Yong Cai ◽  
Min Zhang ◽  
Ling Bo Dang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Failure Mode ◽  
Failure Process ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Replacement Ratio ◽  
Aggregate Concrete

Compressive strengths of recycled aggregate concrete(RAC) with different recycled aggregates(RA) replacement ratios at 7d, 28d, 60d ages are investigated respectively. Failure process and failure mode of RAC are analyzed, influences on compressive strength with same mix ratio and different RA replacement ratios are analyzed, and the reason is investigated in this paper. The experimental results indicate that compressive strength of recycled concrete at 28d age can reach the standard generally, it is feasible to mix concrete with recycled aggregates, compressive strength with 50% replacement ratio is relatively high.

The Properties of Fine Recycled Aggregate Concrete Containing Recycled Bricks from Construction and Demolition Waste

2018 ◽  
Vol 760 ◽  
pp. 193-198 ◽  
Author(s):  
Kristina Fořtová ◽  
Tereza Pavlů
Keyword(s):  
Recycled Aggregate Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Demolition Waste ◽  
Natural Sand ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Recycled Fine Aggregate

This paper presents research results of recycled fine aggregate concrete testing. The main aim of this contribution is verification of properties of fine aggregate concrete with partial replacement of fine natural aggregate by recycled masonry aggregate originated from construction and demolition waste. The influence of partial replacement of natural sand to mechanical properties and freeze-thaw resistance is described. The compressive strength and flexural strength were tested at the age of 28 and 60 days and after 25, 50, 75 and 100 freeze-thaw cycles. Partial replacement of natural sand was 0, 25 and 50 % for all these tests. Prismatic specimens were examined.

The Research of Green High Performance Recycled Construct Materials

2011 ◽  
Vol 71-78 ◽  
pp. 4471-4475
Author(s):  
Xiao Xiong Zha ◽  
Kai Zhang
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Experimental Studies ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Concrete Aggregates ◽  
Recycled Concrete Aggregates ◽  
Large Water

Recycled concrete aggregates have large porosity, large water absorption and high crush index. Mechanical properties of recycled concrete aggregates could be improved by adding activated water instead of ordinary water. On the basis of the experimental studies, this paper analyzes the influences on recycled concrete compression strength when using activated water. There are many different factors such as the kinds and amounts of alkali and the water slag ratio affecting the compressive strength of recycle geopolymer. The results show that activated water has a high enhancement on compressive strength of recycled aggregate concrete, and the highest compressive strength of recycled geopolymer is 57.3MPa.

scholarly journals Compressive performance of 50 MPa strength concrete-filled square and circular tube (CFT) columns using recycled aggregate

2018 ◽  
Author(s):  
Sung-Mo Choi ◽  
Won Ho Choi ◽  
Kangseok Lee ◽  
Jae-Yong Ryoo ◽  
Sunhee Kim ◽  
...  
Keyword(s):  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Steel Pipe ◽  
Strength Development ◽  
Fine Aggregate ◽  
Mixing Ratio ◽  
Compressive Behavior ◽  
Aggregate Concrete ◽  
Cft Column

Recycled aggregate is an environmentally self-sustainable solution that can reduce construction waste and replace natural aggregates. However, there is a disadvantage in concrete such as initial strength drop and long-term strength development. Therefore, the interaction effect of the two materials can be expected by filling the cyclic aggregate concrete in the CFT column. In order to develop a concrete with compressive strength of 50 MPa as a recycled aggregate, we carried out a mixing experiment and fabricated 18 specimens to confirm the compressive behavior of a RCFT (Recycled Concrete Filled Tube) column that can be applied to actual buildings. Variable is the shape and thickness of steel pipe, concrete strength and mixing ratio, and coarse aggregate and fine aggregate are all used as recycled aggregate. The optimum mixing ratio for recycled aggregate concrete to be filled in the CFT filled steel pipe was found through three concrete preliminary mixing experiments. In addition, the compression test of the RCFT column was carried out to observe and analyze the buckling shape of the CFT column. Based on the analysis of the buckling configuration and the experimental data, the load-displacement curves of the specimens were drawn and the compressive behavior was analyzed. 

scholarly journals Basic Mechanical Properties of Basalt Fiber Reinforced Recycled Aggregate Concrete

2017 ◽  
Vol 11 (1) ◽  
pp. 43-53 ◽  
Author(s):  
Huaxin Liu ◽  
Jianwei Yang ◽  
Xiangqing Kong ◽  
Xuxu Xue
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Basalt Fiber ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Mixing Ratio ◽  
Fiber Reinforced ◽  
Aggregate Concrete ◽  
Chopped Basalt Fiber

In order to study the basic mechanical properties of basalt fiber reinforced recycled aggregate concrete, the concrete mix ratio, the length and the volume mixing ratio of chopped basalt fiber yarn are designed for changing factors. A total of 324 specimens have been completed for this investigation. The compressive strength, splitting tensile strength, elastic modulus and axial compressive strength of basalt fiber recycled concrete have carried on the experimental study and theoretical analysis as 81 specimens, respectively. In all specimens, coarse aggregate were replaced by recycled aggregate with a replacement rate of 100%. Experimental results show that the failure process and failure pattern of basalt fiber recycled concrete and ordinary concrete are similar; With the improvement of concrete strength grade; When the volume mixing ratio of chopped basalt fiber yarn is 0.2%, the mechanic performance can effectively improve, and the length of chopped basalt fiber has less effect on the mechanical indexes; The conversion relation between common concrete mechanics index is no longer suitable for basalt fiber recycled concrete, new conversion formulas for basalt fiber recycled concrete between the mechanics index were presented through fitting experimental data.

scholarly journals Performance of Recycled Aggregate Concrete for M25 Grade Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 4694-4700
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Aggregate Concrete ◽  
Inorganic Particles ◽  
Natural Aggregates

Recycled aggregates (RCA) are the aggregates which are made up of crushed, inorganic particles that are obtained from the construction demolition debris. Now a day’s protection of environment is the ultimate challenge to the society. So the usage of RCA’s is the best alternative for the aggregates which are obtained naturally in the construction activity. The scope of using these recycled concrete aggregates is increasing day by day. It reduces the cost effectively as we are using waste concrete as recycled aggregates. The main focus of this paper is to use find the strength qualities of recycled aggregates so as to use it as an alternative for the natural aggregates in high strength concrete for various construction activities. Comparison of workability, compressive strength, tensile strength, elastic modulus and flexural strength of recycled aggregate concrete is made with natural aggregate concrete. Here M25 grade concrete is taken and the natural aggregates were replaced with recycled aggregates in various percentages of 0%, 25%, 50%, 75% and 100%. The mix design for these replacement ratios are done by using code of IS 10262-2009. In order to determine the properties which were mentioned above a total of 60 cubes, 10 beams and 40 cylinders were casted. The compressive strength and tensile strength of RCA concrete have been determined for 7 days and 28 days where as the modulus of elasticity and the flexural strength of RCA concrete are determined after curing for the period of 28 days. The tests done on RCA concrete are compared with concrete which is obtained by natural aggregates As per IS codification the parameters which were determined are reducing moderately as the amount of aggregates which are recycled is being raised

scholarly journals Experimental study on mechanical properties and microstructures of steel fiber-reinforced fly ash-metakaolin geopolymer-recycled concrete

2021 ◽  
Vol 60 (1) ◽  
pp. 578-590
Author(s):  
Zhong Xu ◽  
Zhenpu Huang ◽  
Changjiang Liu ◽  
Xiaowei Deng ◽  
David Hui ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Steel Fiber ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Mix Proportion ◽  
Optimal Mix

Abstract Geopolymer cementitious materials and recycled aggregate are typical representatives of material innovation research in the engineering field. In this study, we experimentally investigated a method to improve the performance of geopolymer-recycled aggregate concrete (GRAC). The recycled concrete aggregates and steel fiber (SF), fly ash (FA), metakaolin (MK), and sodium silicate solution were used as the main raw materials to prepare fiber-reinforced geopolymer-recycled aggregate concrete (FRGRAC). First, the orthogonal test was carried out to study the GRAC, and the optimal mix proportion was found. Second, building on the optimal mix proportion, the effects of the SF content on the slump, 7 and 28 days compressive strength, tensile strength, and flexural strength of FRGRAC were further studied. Finally, the microscopic mechanism of FRGRAC was studied by scanning electron microscopy (SEM). The study results indicate that the slump continues to decrease as the fiber content increases, but the compressive strength, tensile strength, and flexural strength increase to a certain extent. Through SEM analysis, it is found that SF restrains the development of cracks and improves the strength of concrete.

Sign in / Sign up

Export Citation Format

Share Document