scholarly journals Experimental modal identification and fem updating of a seven story isolated educational building

2019 ◽  
Vol 29 (2) ◽  
Author(s):  
Rony Reategui ◽  
Estefanía Bossus ◽  
Mauricio Gonzales ◽  
Diego Villagomez ◽  
Rafael Aguilar
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Models ◽  
Dynamic Properties ◽  
Structural Response ◽  
Experimental Tests ◽  
Cost Effective ◽  
Element Model ◽  
Modal Identification ◽  
Ambient Vibration ◽  
National Regulation

The construction of isolated structures is increasing in recent decades in seismic countries. In Peru, the national regulation indicates that important buildings such as hospitals located in areas of high seismic risk must incorporate isolation systems to reduce structural and nonstructural loss. These systems protect the main structure from the effects of a seismic event by separating its base from the earth movement and by reducing the relative displacements and accelerations between adjacent stories. In the structural design process of buildings and seismic protection systems, having numerical models that properly represent the real behavior of the buildings is of high importance. In this context, experimental modal tests represents an attractive cost-effective non-destructive tool to obtain an accurate characterization of the experimental structural response. This paper presents the experimental tests carried out in a base-isolated educational building built in 2014 that has seven stories and three basements with a total built area of around 7500 m2. Data acquisition was accomplished with autonomous units (acquisition system and transducers incorporated in a single unit) whose versatility allowed measuring a significant number of degrees of freedom in a limited amount of time. The dynamic properties experimentally identified were used to calibrate the finite element model of the building. The results showed that the design model approximates correctly to the experimentally identified ambient vibration response when considering rigid supporting conditions as well as the interaction of partitioning elements such as walls and parapets.

Analysis of a damaged 12-storey frame-wall concrete building during the 2010 Haiti earthquake — Part II: Nonlinear numerical simulations

2013 ◽  
Vol 40 (8) ◽  
pp. 803-814 ◽  
Author(s):  
Benoit Boulanger ◽  
Patrick Paultre ◽  
Charles-Philippe Lamarche
Keyword(s):  
Structural Damage ◽  
Numerical Models ◽  
Dynamic Properties ◽  
Shear Walls ◽  
Element Model ◽  
Companion Paper ◽  
Ambient Vibration ◽  
Wall Structure ◽  
Haiti Earthquake ◽  
Concrete Building

After the 2010 Haiti earthquake, which destroyed a significant part of the seismically vulnerable city of Port-au-Prince, the country’s capital, a 12-storey reinforced concrete building that behaved well was investigated to understand its dynamic response. This paper completes the experimental work presented in a companion paper, in which the dynamic properties of the building were obtained from ambient vibration tests, and from which a finite-element model was updated. This paper’s main objectives are: (i) to understand the causes that led to the observed structural damage; and (ii) to estimate the likely seismic excitation at the site of the building. Several nonlinear analyses involving various ground motion intensities were conducted and the results were compared with the damage reported during the on-site survey. The numerical models reproduced the observed damages well and helped to explain them. The overall response of the mixed stiff frame–wall structure was clearly dominated by the high stiffness of the shear walls, showing that this type of structural system helps in keeping reasonable interstorey drift levels. Overall, the building’s structure seems to have responded linearly to all the ground motions investigated, but deformation demands imposed to the frame by the shear walls lead to local damages.

scholarly journals Identification of Historical Veziragasi Aqueduct Using the Operational Modal Analysis

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
E. Ercan ◽  
A. Nuhoglu
Keyword(s):  
Modal Analysis ◽  
Natural Frequencies ◽  
Model Updating ◽  
Dynamic Properties ◽  
Dynamic Test ◽  
Element Model ◽  
Operational Modal Analysis ◽  
Modal Identification ◽  
Ambient Vibration ◽  
Mode Shapes

This paper describes the results of a model updating study conducted on a historical aqueduct, called Veziragasi, in Turkey. The output-only modal identification results obtained from ambient vibration measurements of the structure were used to update a finite element model of the structure. For the purposes of developing a solid model of the structure, the dimensions of the structure, defects, and material degradations in the structure were determined in detail by making a measurement survey. For evaluation of the material properties of the structure, nondestructive and destructive testing methods were applied. The modal analysis of the structure was calculated by FEM. Then, a nondestructive dynamic test as well as operational modal analysis was carried out and dynamic properties were extracted. The natural frequencies and corresponding mode shapes were determined from both theoretical and experimental modal analyses and compared with each other. A good harmony was attained between mode shapes, but there were some differences between natural frequencies. The sources of the differences were introduced and the FEM model was updated by changing material parameters and boundary conditions. Finally, the real analytical model of the aqueduct was put forward and the results were discussed.

scholarly journals Comparison of different finite element model updates based on experimental onsite testing: the case study of San Giovanni in Macerata

2021 ◽  
Author(s):  
Carlo Baggio ◽  
Valerio Sabbatini ◽  
Silvia Santini ◽  
Claudio Sebastiani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Numerical Models ◽  
Dynamic Properties ◽  
Structural Parameters ◽  
Element Model ◽  
Ambient Vibration ◽  
Geotechnical Investigations ◽  
Historic Structures

AbstractUnderstanding the behavior of historic structures that have undergone structural changes, restorations, and damage over time is still a significant challenge for structural engineers, particularly in those countries subject to high seismic risk, such as Italy. The study of built heritage for its prevention and conservation is an active research topic, due to the numerous uncertainties present in historic structures. Finite element modelling has become the most common and accessible method to study the behavior of complex masonry structures, however, the gap between numerical and experimental analysis may lead to erroneous results. Model updating techniques can reduce the discrepancy between the behavior of the numerical models and the testing results. The goal of this work is to illustrate a methodology to integrate the information derived from local, global, and geotechnical investigations into the finite element model of the masonry historical church of San Giovanni in Macerata, considering the Douglas–Reid model updating method. The PRiSMa laboratory of Roma Tre University carried out local investigations such as sonic tomography, video endoscopy and double flat jack tests, along with five ambient vibration tests that were processed through the operational modal analysis to extrapolate the dynamic properties of the building (modal frequency, modal shape vector and modal damping). The combined use of global, local and geotechnical information implemented in the methodology effectively reduced the uncertainties of the model and led the refinement and validation of the most relevant structural parameters.

Coupled torsional dynamic analysis of a multistory building

1973 ◽  
Vol 63 (3) ◽  
pp. 1025-1039
Author(s):  
Bruce M. Douglas ◽  
Thomas E. Trabert
Keyword(s):  
Ground Motion ◽  
Degrees Of Freedom ◽  
Seismic Waves ◽  
Structural Response ◽  
Tall Buildings ◽  
Strong Motion ◽  
Ambient Vibration ◽  
Simultaneous Application ◽  
Vibration Data ◽  
Horizontal Ground Motion

abstract The coupled bending and torsional vibrations of a relatively symmetric 22-story reinforced concrete building in Reno, Nevada are studied. Analytical results are compared with observations obtained during the nuclear explosion FAULTLESS and to ambient vibration data. The fundamental periods of vibration observed during FAULTLESS were (TNS = 1.42, TEW = 1.81, TTORSION = 1.12 sec), and the calculated periods were (TNS = 2.14, TEW = 2.07, TTORSION = 1.90 sec). It was estimated that between 25 and 45 per cent of the total available nonstructural stiffness was required to explain the differences in the observed and calculated fundamental periods. Each floor diaphragm in the system was allowed three degrees of freedom-two translations and a rotation. It was found that coupled torsional motions can influence the response of structural elements near the periphery of the structure. Strong-motion structural response calculations comparing the simultaneous use of both components of horizontal ground motion to a single component analysis showed that the simultaneous application of both components of ground motion can significantly alter the response of lateral load-carrying elements. Differences of the order of 45 per cent were observed in the frames near the ends of the structure. Also, it was shown that the overall response of tall buildings is sensitive not only to the choice of input ground motion but also to the orientation of the structure with respect to the seismic waves.

On the Structural Response of a Flexible Pipe With Damaged Tensile Armor Wires

2011 ◽  
Author(s):  
Jose´ Renato M. de Sousa ◽  
George C. Campello ◽  
Antoˆnio Fernando B. Bueno ◽  
Eduardo Vardaro ◽  
Gilberto B. Ellwanger ◽  
...  
Keyword(s):  
Mechanical Response ◽  
High Stress ◽  
Three Dimensional ◽  
Structural Response ◽  
Experimental Tests ◽  
Element Model ◽  
Axial Stiffness ◽  
Stress Concentrations ◽  
Flexible Pipe ◽  
Flexible Pipes

This paper studies the structural response of a 6.0″ flexible pipe under pure tension considering two different situations: the pipe is intact or has five wires broken in its outer tensile armor. A three-dimensional nonlinear finite element model devoted to analyze the local mechanical response of flexible pipes is employed in this study. This model is capable of representing each wire of the tensile armors and, therefore, localized defects, including total rupture, may be adequately represented. Results from experimental tests are also presented in order to validate the theoretical estimations. The theoretical and experimental results indicate that the imposed damage reduced the axial stiffness of the pipe. High stress concentrations in the wires near the damaged ones were also observed and, furthermore, the stresses in the inner carcass and the pressure armor are affected by the imposed damage, but, on the other hand, the normal stresses in the wires of the inner tensile armor are not.

scholarly journals Displacement Study of a Large-Scale Freeform Timber Plate Structure Using a Total Station and a Terrestrial Laser Scanner

Sensors ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 413 ◽  
Author(s):  
Anh Chi Nguyen ◽  
Yves Weinand
Keyword(s):  
Large Scale ◽  
Numerical Models ◽  
Laser Scanner ◽  
Experimental Tests ◽  
Point Clouds ◽  
Element Model ◽  
Experimental Investigations ◽  
Bottom Surface ◽  
Terrestrial Laser Scanner ◽  
Total Station

Recent advances in timber construction have led to the realization of complex timber plate structures assembled with wood-wood connections. Although advanced numerical modelling tools have been developed to perform their structural analysis, limited experimental tests have been carried out on large-scale structures. However, experimental investigations remain necessary to better understand their mechanical behaviour and assess the numerical models developed. In this paper, static loading tests performed on timber plate shells of about 25 m span are reported. Displacements were measured at 16 target positions on the structure using a total station and on its entire bottom surface using a terrestrial laser scanner. Both methods were compared to each other and to a finite element model in which the semi-rigidity of the connections was represented by springs. Total station measurements provided more consistent results than point clouds, which nonetheless allowed the visualization of displacement fields. Results predicted by the model were found to be in good agreement with the measurements compared to a rigid model. The semi-rigid behaviour of the connections was therefore proven to be crucial to precisely predict the behaviour of the structure. Furthermore, large variations were observed between as-built and designed geometries due to the accumulation of fabrication and construction tolerances.

scholarly journals In-Plane Behaviour of Masonry Walls: Numerical Analysis and Design Formulations

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5780
Author(s):  
Thomas Celano ◽  
Luca Umberto Argiento ◽  
Francesca Ceroni ◽  
Claudia Casapulla
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Numerical Models ◽  
Experimental Tests ◽  
Element Model ◽  
Masonry Walls ◽  
Analysis And Design ◽  
Non Linear ◽  
Failure Loads ◽  
Modelling Approaches

This paper presents the results of several numerical analyses aimed at investigating the in-plane resistance of masonry walls by means of two modelling approaches: a finite element model (FEM) and a discrete macro-element model (DMEM). Non-linear analyses are developed, in both cases, by changing the mechanical properties of masonry (compressive and tensile strengths, fracture energy in compression and tension, shear strength) and the value of the vertical compression stress applied on the walls. The reliability of both numerical models is firstly checked by means of comparisons with experimental tests available in the literature. The analyses show that the numerical results provided by the two modelling approaches are in good agreement, in terms of both failure loads and modes, while some differences are observed in their load-displacement curves, especially in the non-linear field. Finally, the numerical in-plane resistances are compared with the theoretical formulations provided by the Italian building code for both flexural and shear failure modes and an amendment for the shape factor ‘b’ introduced in the code formulation for squat walls is proposed.

Assessment of the Realistic Stiffness and Capacity of the Connections in Quincha Frames to Develop Numerical Models

2013 ◽  
Vol 778 ◽  
pp. 526-533 ◽  
Author(s):  
Natalie Quinn ◽  
Dina D’Ayala
Keyword(s):  
Finite Element ◽  
Numerical Models ◽  
Experimental Tests ◽  
Element Model ◽  
Accurate Representation ◽  
Timber Frame ◽  
Historic Structures ◽  
The World ◽  
Infill Material ◽  
High Degree

Peru is one of the most seismically active countries in the world, this fact highlighted by several destructive earthquakes in recent years. The centre of Lima has a large number of historic structures with a ground floor in adobe, and their upper storeys in quincha, a traditional technique consisting of a timber frame with an infill of canes and mud. Despite the existence of a large number of buildings containing this technique, very little is known about its seismic performance. In order to investigate this, a series of experimental tests on quincha frames, with and without the infill, have been carried out previously, with the aim of quantifying the lateral behaviour and identifying vulnerable areas. The present paper details work carried out to develop a finite element model of the test frames without infill. This model of the timber frame will enable an accurate representation of the frame behaviour to be developed before adding the infill of canes and mud to the model. As the behaviour of the infill material and its connection to the frame is difficult to determine, characterising the timber frame with a high degree of accuracy ensures that the contribution of the infill can be globally quantified from the overall experimental results. The beams and posts are connected by cylindrical mortice and tenon joints, with a diagonal bracing member providing some lateral restraint. The connections have been modelled semi-rigid springs, with the stiffness calculated using variations of the component method. This was found to give very similar results to those obtained experimentally.

Wavelet-based multi-scale finite element modeling and modal identification for structural damage detection

2017 ◽  
Vol 20 (8) ◽  
pp. 1185-1195 ◽  
Author(s):  
Wen-Yu He ◽  
Songye Zhu ◽  
Zhi-Wei Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Damage Detection ◽  
Structural Damage ◽  
Degrees Of Freedom ◽  
Element Model ◽  
Modal Identification ◽  
Multi Scale ◽  
Multi Resolution Analysis ◽  
Resolution Analysis

Wavelet techniques enable multi-resolution analysis that can represent a function (either field or signal function) in a multi-scale manner. This article presents a damage detection method with dynamically changed scales in both temporal and spatial domains, by taking advantage of the wavelet-based multi-resolution analysis. This method combines a wavelet-based finite element model (WFEM) that employs B-spline wavelet as shape functions and wavelet-based modal identification method to detect structural damage progressively. High-fidelity modal information can be computed or identified with minimized computation cost by lifting the wavelet scales in the wavelet-based finite element model and in signal processing individually according to the actual requirements. Numerical examples demonstrate that the accuracy of damage detection is improved considerably by this lifting strategy during the damage detection process. Besides, fewer degrees of freedom are involved in the wavelet-based finite element model than those of traditional finite element method. The computational efficiency can be improved to large extent and computation resources can be utilized more rationally using the proposed multi-scale approach.

Blind Modal Identification of Non-Classically Damped Systems from Free or Ambient Vibration Records

2013 ◽  
Vol 29 (4) ◽  
pp. 1137-1157 ◽  
Author(s):  
Fariba Abazarsa ◽  
Fariborz Nateghi ◽  
S. Farid Ghahari ◽  
Ertugrul Taciroglu
Keyword(s):  
Degrees Of Freedom ◽  
Passive Control ◽  
Modal Identification ◽  
Ambient Vibration ◽  
Mode Shapes ◽  
Audio Signals ◽  
Civil Structures ◽  
Ambient Vibration Tests ◽  
Vibration Tests ◽  
Damped Systems

A significant segment of system identification literature on civil structures is devoted to response-only identification, simply because lack of measurements of input excitations for civil structures is a fairly common scenario. In recent years, several researchers have successfully adapted a second-order blind identification (SOBI) technique—a method originally developed for “blind source separation” of audio signals—to response-only identification of mechanical and civil structures. However, this development had been confined to fully instrumented classically damped systems. While several approaches have been proposed recently for extending SOBI to non-classically damped systems, they all require additional data such as velocity or analytic signals. Herein, we present a version of SOBI that requires only acceleration signals recorded during free or ambient vibration tests, and yields the system's complex mode shapes, natural frequencies, and damping ratios. Performance of the proposed technique is demonstrated through two synthetic examples: a ten-story structure possessing a passive control system, and a soil-structure system with seven degrees of freedom (seven-DOF).

Sign in / Sign up

Export Citation Format

Share Document