scholarly journals The effects of electron irradiation and thermal dependence measurements on 4H-Sic Schottky diode

2017 ◽  
Vol 51 (12) ◽  
pp. 1721
Author(s):  
Sabuhi Ganiyev ◽  
M. Azim Khairi ◽  
D. Ahmad Fauzi ◽  
Yusof Abdullah ◽  
N.F. Hasbullah
Keyword(s):  
Barrier Height ◽  
Ideality Factor ◽  
Elevated Temperatures ◽  
Series Resistance ◽  
Schottky Diodes ◽  
High Energy ◽  
Bias Current ◽  
N Saturation ◽  
Saturation Current ◽  
Current Voltage

In this paper the effects of high energy (3.0 MeV) electrons irradiation over a dose ranges from 6 to 15 MGy at elevated temperatures 298 to 448 K on the current-voltage characteristics of 4H-SiC Schottky diodes were investigated. The experiment results show that after irradiation with 3.0 MeV forward bias current of the tested diodes decreased, while reverse bias current increased. The degradation of ideality factor, n, saturation current, Is, and barrier height, Phib, were not noticeable after the irradiation. However, the series resistance, Rs, has increased significantly with increasing radiation dose. In addition, temperature dependence current-voltage measurements, were conducted for temperature in the range of 298 to 448 K. The Schottky barrier height, saturation current, and series resistance, are found to be temperature dependent, while ideality factor remained constant. DOI: 10.21883/FTP.2017.12.45193.8646

Current-Voltage and Capacitance-Voltage Characteristics of Pd Schottky Diodes Fabricated on ZnO Grown along Zn- and O-Faces

2013 ◽  
Vol 313-314 ◽  
pp. 270-274
Author(s):  
M. Faisal ◽  
M. Asghar ◽  
Khalid Mahmood ◽  
Magnus Willander ◽  
O. Nur ◽  
...  
Keyword(s):  
Barrier Height ◽  
Ideality Factor ◽  
Doping Concentration ◽  
Series Resistance ◽  
Schottky Diodes ◽  
Thermionic Emission ◽  
Temperature Dependent ◽  
Current Voltage ◽  
Capacitance Voltage ◽  
Increasing Temperature

Temperature dependent current-voltage (I-V) and capacitance-voltage (C-V) measurements were utilized to understand the transport mechanism of Pd Schottky diodes fabricated on Zn- and O-faces of ZnO. From I-V measurements, in accordance with the thermionic emission mechanism theory, it was found that the series resistance Rsand the ideality factor n were strongly temperature dependent that decreased with increasing temperature for both the faces (Zn and O-face) of ZnO revealing that the thermionic emission is not the dominant process. The barrier height øB(I-V)increased with increasing temperature for both faces. The measured values of ideality factor, barrier height and series resistance for Zn- and O-faces at room temperature were 4.4, 0.60 eV, 217 Ω and 2.8, 0.49 eV, 251 Ω respectively. The capacitance-voltage (C–V) measurements were used to determine the doping concentration Nd, the built-in-potential Vbi, and the barrier height øB(C-V). The doping concentration was found to be decreased with increasing depth. The barrier height øB(C-V)calculated for O-polar and Zn-polar faces decreases with increasing temperature. The values of barrier height øB(C-V)determined from C-V measurements were found higher than the values of barrier height øB(I-V). Keeping in view the calculated values of ideality factor, barrier height, and series resistance shows that O-polar face is qualitatively better than Zn-polar face.

scholarly journals Silicon carbide schottky diodes forward and reverse current properties upon fast electron radiation

2019 ◽  
Vol 8 (2) ◽  
pp. 428-437
Author(s):  
M. Azim Khairi ◽  
Rosminazuin Ab. Rahim ◽  
Norazlina Saidin ◽  
Yusof Abdullah ◽  
Nurul Fadzlin Hasbullah
Keyword(s):  
Silicon Carbide ◽  
Electron Irradiation ◽  
Ideality Factor ◽  
Reverse Bias ◽  
Series Resistance ◽  
Schottky Diodes ◽  
Forward Bias ◽  
Bias Current ◽  
Saturation Current ◽  
Order Of Magnitude

This paper investigates on the reaction of 10 and 15MGy, 3MeV electron irradiation upon off-the-shelves (commercial) Silicon Carbide Schottky diodes from Infineon Technologies (model: IDH08SG60C) and STMicroelectronics (model: STPSC806). Such irradiation reduces the forward-bias current. The reduction is mainly due to the significant increase of the series resistance (i.e. Infineon: 1.45Ω at before irradiation → 121×103 Ω at 15MGy); STMicroelectronics: 1.44Ω at before irradiation → 2.1×109 Ω at 15MGy). This increase in series resistance gives 4.6 and 8.2 orders of magnitude reduction for the forward-bias current density of Infineon and STMicroelectronics respectively. It is also observed that the ideality factor and the saturation current of the diodes increases with increasing dose (i.e. ideality factor- Infineon: 1.01 at before irradiation → 1.05 at 15MGy; STMicroelectronics: 1.02 at before irradiation → 1.3 at 15MGy | saturation current- Infineon: 1.6×10-17A at before irradiation → 2.5×10-17A at 15MGy; STMicroelectronics: 2.4×10-15A at before irradiation → 8×10-15A at 15MGy). Reverse-bias leakage current density in model by Infineon increases by one order of magnitude after 15MGy irradiation, however, in model by STMicroelectronics decreases by one order of magnitude. Overall, for these particular samples studied, Infineon devices have shown to be better in quality and more radiation resistance toward electron irradiation in forward-bias operation while STMicroelectronics exhibit better characteristics in reverse-bias operation.

Analysis of current–voltage and capacitance–voltage characteristics of Zr/p-Si Schottky diode with high series resistance

2020 ◽  
Vol 34 (10) ◽  
pp. 2050095
Author(s):  
Durmuş Ali Aldemir
Keyword(s):  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Series Resistance ◽  
Zero Bias ◽  
Acceptor Concentration ◽  
Current Voltage ◽  
Capacitance Voltage ◽  
High Series ◽  
Contact Parameters

Zr/p-Si Schottky diode was fabricated by DC magnetic sputtering of Zr on p-Si. Zr rectifying contact gave a zero bias barrier height of 0.73 eV and an ideality factor of 1.33 by current–voltage measurement. The experimental zero bias barrier height was higher than the value predicted by metal-induced gap states (MIGSs) and electronegativity theory. The forward bias current was limited by high series resistance. The series resistance value of 9840 [Formula: see text] was determined from Cheung functions. High value of the series resistance was ascribed to low quality ohmic contact. In addition to Cheung functions, important contact parameters such as barrier height and series resistance were calculated by using modified Norde method. Re-evaluation of modified Norde functions was realized in the direction of the method proposed by Lien et al. [IEEE Trans. Electron Devices 31 (1984) 1502]. From the method, the series resistance and ideality factor values were found to be as 41.49 [Formula: see text] and 2.08, respectively. The capacitance–voltage characteristics of the diode were measured as a function of frequency. For a wide range of applied frequency, the contact parameters calculated from [Formula: see text]–[Formula: see text] curves did not exhibit frequency dependence. The barrier height value of 0.71 eV which was in close agreement with the value of zero bias barrier height was calculated from [Formula: see text]–[Formula: see text] plot at 1 MHz. The values of acceptor concentration obtained from [Formula: see text]–[Formula: see text] curves showed consistency with actual acceptor concentration of p-Si.

Temperature dependence of current-voltage characteristics in μc-Si:H and pm-Si:H PIN structures

2012 ◽  
Vol 1426 ◽  
pp. 365-370
Author(s):  
Francisco Temoltzi Avila ◽  
Andrey Kosarev ◽  
Ismael Cosme ◽  
Mario Moreno ◽  
P. Roca y Cabarrocas
Keyword(s):  
Temperature Dependence ◽  
Temperature Change ◽  
Ideality Factor ◽  
Dark Current ◽  
Series Resistance ◽  
Equivalent Circuit Model ◽  
Saturation Current ◽  
Current Voltage ◽  
Current Voltage Characteristics

ABSTRACTThe dark current-voltage characteristics of PIN structures are studied and analyzed for PV samples as for integral device without taking account the performance of the different elements typically used in equivalent circuit model such as diode n-factor, shunt and series resistances. The contribution of all these elements is very important in the development of devices because they determine the performance characteristics. In this work we have studied and compared the temperature dependence of current-voltage characteristics in μc-Si:H and pm-Si:H p-i-n structures having approximately the same efficiencies with emphasis on their different electronic characteristics such as shunt (Rsh) and series (Rs) resistance, ideality factor (n), and the saturation current (Is), which give us some ideas on role of these elements. In the pm-Si:H cell it was observed that the Rs increases with the increase of the temperature in contrast to the μc-Si:H structures, where the series resistance reduces with temperature change from T = 300 up to 480K. In both the pm-Si:H and μc-Si:H samples Rshreduces with temperature change from 300 up to 480 K. The ideality factor in the pm-Si:H structure shows an increase, and in μc-Si:H a reduction, when temperature increases. Saturation current in both cases increases with temperature as it was expected. From the saturation current it was obtained the build-in potential. Analysis behavior of both saturation current and n-factor with temperature shows that build-in potential increases with temperature in the pm-Si:H, but reduces in μc-Si:H structure.

scholarly journals Characterization of Schottky Diodes on 4H-SiC with Various Off-Axis Angles Grown by Sublimation Epitaxy

2008 ◽  
Vol 600-603 ◽  
pp. 967-970 ◽  
Author(s):  
Mitsutaka Nakamura ◽  
Yoshikazu Hashino ◽  
Tomoaki Furusho ◽  
Hiroyuki Kinoshita ◽  
Hiromu Shiomi ◽  
...  
Keyword(s):  
Ideality Factor ◽  
Basal Plane ◽  
Reverse Bias ◽  
Schottky Barrier Height ◽  
Schottky Diodes ◽  
Bias Current ◽  
Device Performance ◽  
Current Voltage ◽  
Current Voltage Characteristics

The effects of basal-plane defects on the performance of 4H-SiC Schottky diodes using a Ni electrode are demonstrated. Systematic characterization was performed using 4H-SiC epitaxial layers grown by sublimation epitaxy on substrates with various off-axis angles. As the off-axis angle increases, the ideality factor of the current-voltage characteristics increases, and the Schottky barrier height decreases, corresponding to an increase in the number of basal-plane defects. The reverse-bias current degrades for high off-axis samples. These results indicate that basal-plane defects degrade the device performance. Schottky diodes that possesses good characteristics were obtained for samples with low off-axis angles (2o- and 4o-off samples).

Temperature Dependent Current-Voltage Characteristics of n-Type β-FeSi2/Intrinsic Si/p-Type Si Heterojunctions

2015 ◽  
Vol 1120-1121 ◽  
pp. 435-439
Author(s):  
Nathaporn Promros ◽  
Dalin Prajakkan ◽  
Nantharat Hongsa ◽  
Nattanee Suthayanan ◽  
Phongsaphak Sittimart ◽  
...  
Keyword(s):  
Current Density ◽  
Ideality Factor ◽  
Series Resistance ◽  
Linear Part ◽  
Thermionic Emission ◽  
Saturation Current ◽  
Current Voltage ◽  
Saturation Current Density ◽  
Current Voltage Characteristics ◽  
P Type

In this work, n-type β-FeSi2/intrinsic Si/p-type Si heterojunctions were prepared by facing-targets direct-current sputtering. We measured their current-voltage characteristics at low temperatures ranging from 300 K down to 50 K and investigated their ideality factor, saturation current and series resistance using thermionic emission theory and Cheung’s method. From thermionic emission theory, the ideality factor and saturation current density were calculated from the slope of the linear part from the forward lnJ-V and the straight line intercept of lnJ-V at zero voltage, respectively. When the temperature decreased from 300 K down to 50 K, the ideality factor increased from 1.12 to 11.13, whereas the saturation current density decreased from 2.09 × 10-6 A/cm2 to 1.06 × 10-9 A/cm2. Using Cheung’s method, we plotted the relations of dV/d(lnJ)-J and H(J)-J in order to estimate the series resistance from the slope of both plots. In addition, we estimated the ideality factor from a y-axis intercept of the dV/d(lnJ)-J plot. The series resistances from both plots were consistent with each other and increased with the decreasing temperature. The ideality factor estimated by Cheung’s method was in agreement with that obtained from estimation by thermionic emission theory.

scholarly journals Comparison of electrical properties of CuO/n-Si contacts with Cu/n-Si

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Reşit Özmenteş ◽  
Cabir Temirci
Keyword(s):  
Electrical Properties ◽  
Barrier Height ◽  
Ideality Factor ◽  
Series Resistance ◽  
Reference Sample ◽  
Forward Bias ◽  
Schottky Contact ◽  
Experimental Result ◽  
Current Voltage ◽  
Capacitance Voltage

AbstractIn this study, CuO/n-Si/Al heterojunction contacts were fabricated by thermal evaporation technique. Electrical characteristics of the samples were investigated with the current-voltage (I-V), capacitance-voltage/frequency (C-V/f), and conductance-voltage (G/V) measurements at room temperature. Also, Cu/n-Si/Al Schottky contact was produced as a reference sample to investigate the electrical properties of the samples. The values of ideality factor (n), barrier height (Φb) and series resistance (Rs) of the samples were calculated from the forward bias current-voltage (I-V) and reverse bias capacitance-voltage (C-V) characteristics. Also, for checking the consistency of the results, Cheung and Norde functions were used. The experimental result values of CuO/n-Si contact were compared with the values of the reference Cu/n-Si Schottky diode. It was observed that the values of the ideality factor and barrier height of the CuO/n-Si heterojunction were higher than those of the Cu/n-Si Schottky contact, while the series resistance was lower. Also, it has been observed that the value of capacitance decreased with increasing frequency and after a certain value of frequency it was almost constant. The ideality factor of CuO/n-Si/Al heterostructure is about 2.40 and so, it is not close to the ideal behavior.

Electrical Properties Dependent on Schottky Diode Pd/PSC-pSi(100) Based on Hydrocarbon Gas Sensor

2009 ◽  
Vol 609 ◽  
pp. 195-199
Author(s):  
A. Keffous ◽  
M. Kechouane ◽  
Tahar Kerdja ◽  
Y. Belkacem ◽  
K. Bourenane ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Barrier Height ◽  
Schottky Diode ◽  
Ideality Factor ◽  
Gas Sensing ◽  
Series Resistance ◽  
Schottky Diodes ◽  
Electrical Parameters ◽  
Porous Sic ◽  
Sic Films

In this paper we present the study of a Schottky diode gas sensing by using porous SiC films with palladium as a catalytic metal. The Schottky diodes were used for the first time for hydrocarbon (C2H6) gas sensing. The properties of the porous SiC films formed by electrochemical method were investigated by scanning electron microscopy (SEM). The electrical measurements were made at room temperature (295 K) in different ambient. The effect of the porous surface structure was investigated by evaluating electrical parameters such as the ideality factor (n), barrier height (Bp) and series resistance (Rs). The porous layer significantly affects the electrical properties of the Schottky diodes. Analysis of current-voltage (I-V) characteristics showed that the forward current might be described by a classical thermal emission theory. The ideality factor determined by the I–V characteristics was found to be dependent on the SiC thickness. For a thinner SiC layer (0.16 µm), the electrical parameters n was found around 1.135, 0.7041 eV for a barrier height and 45  for a series resistance, but for a thicker one (1.6 µm) n, Bp and Rs were 1.368, 0.7756 eV and 130 , respectively. The low value of the series resistance obtained using Cheung’s method clearly indicated the high performance of the Schottky diode for thinner SiC layer. This effect showed the uniformity of the SiC layer. Finally, sensitivity around 66 % and selectivity of the sensors were reached by using the PSC layer at low voltages below 0.5 Volt.

Time Dependence of Current–Voltage Characteristics of Pb/p-Si Schottky Diode under Hydrostatic Pressure

2011 ◽  
Vol 66 (8-9) ◽  
pp. 576-580 ◽  
Author(s):  
Nazim Ucar ◽  
Ahmet Faruk Özdemira ◽  
Durmus Ali Aldemira ◽  
Güven Çankayab
Keyword(s):  
Hydrostatic Pressure ◽  
Barrier Height ◽  
Ideality Factor ◽  
Interfacial Layer ◽  
Schottky Barrier Height ◽  
Schottky Diodes ◽  
Pressure Coefficient ◽  
Characteristic Parameters ◽  
Current Voltage ◽  
Current Voltage Characteristics

Abstract The effect of time on the characteristic parameters of Pb/p-Si Schottky diodes has been presented as a function of hydrostatic pressure. Current-voltage curves of the Pb=p-Si Schottky diodes have been measured at immediate, 15, 30, 60, and 120 min intervals under 1, 2, and 4 kbar hydrostatic pressure. It has been found that the values of the ideality factor have been approximately unchanged with increasing time. On the other hand, the barrier height of the Pb=p-Si structure slowly increase with increasing time, while these parameters also change with hydrostatic pressure. The diode shows nonideal current-voltage behaviour with an ideality factor greater than unity that can be ascribed to the interfacial layer and the interface states. In addition, the Schottky barrier height increases with a linear pressure coefficient of 92 meV=kbar, which is higher than the pressure coefficient of the silicon fundamental band gap.

Electrical Characteristics of n-Type Nanocrystalline FeSi2/Intrinsic Si/p-Type Si Heterojunctions Prepared by Facing-Targets Direct-Current Sputtering

2013 ◽  
Vol 446-447 ◽  
pp. 88-92
Author(s):  
Nathaporn Promros ◽  
Suguru Funasaki ◽  
Ryūhei Iwasaki ◽  
Tsuyoshi Yoshitake
Keyword(s):  
Barrier Height ◽  
Ideality Factor ◽  
Low Temperatures ◽  
Series Resistance ◽  
Linear Part ◽  
Thermionic Emission ◽  
Straight Line ◽  
Current Voltage ◽  
P Type ◽  
Direct Current Sputtering

n-Type nanocrystalline FeSi2/intrinsic Si/p-type Si heterojunctions were prepared by FTDCS. In order to estimate their diode parameters such as ideality factor, barrier height and series resistance, their current-voltage characteristics were measured in the temperature range from 300 to 77 K and analyzed on the basis of thermionic emission theory and Cheungs method. Based on thermionic emission theory, the ideality factor was calculated from the slope of the linear part from the forward lnJ-V characteristics. The barrier height was calculated once the saturation current density was derived from the straight line intercept of lnJ-V plot at a zero voltage. The obtained results exhibit an increase of ideality factor and a decrease of barrier height at low temperatures, which might be owing to inhomogeneity of material and non-uniformity of charge at the interface. Based on Cheungs method, the ideality factor and barrier height were estimated from y-axis intercept of dV/d (lnJ)J plot and y-axis intercept of H(J)J plot, respectively. The series resistance was analyzed from the slopes of dV/d (lnJ)J and H(J)J plots. The values of ideality factor and barrier height obtained from this method are in agreement with those obtained from the thermionic emission theory. The obtained series resistances from dV/d (lnJ)J and H(J)J plots, which were approximately equal to each others, were increased as the temperature decreased. This result should be owing to the increased ideality factor and remarkably reduced carrier concentrations at low temperatures.

Sign in / Sign up

Export Citation Format

Share Document