scholarly journals Низкотемпературный синтез нанокристаллов alpha-SiC

2019 ◽  
Vol 61 (12) ◽  
pp. 2447
Author(s):  
К.Х. Нусупов ◽  
Н.Б. Бейсенханов ◽  
Д.И. Бакранова ◽  
С. Кейнбай ◽  
А.А. Турахун ◽  
...  
Keyword(s):  
Silicon Carbide ◽  
Low Temperature ◽  
Ir Spectroscopy ◽  
Magnetron Sputtering ◽  
Rf Magnetron Sputtering ◽  
Rf Plasma ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Ions ◽  
Sic Film

Abstract Thick SiC_ x films have been deposited on a c -Si surface by radiofrequency (rf) magnetron sputtering (150 W, 13.56 MHz, Ar flow 2.4 L/h, 0.4 Pa) of graphite and silicon targets. The X-ray diffraction study shows that fast annealing of the SiC_ x film deposited on the c -Si surface for 3 h leads to the low-temperature (970°C) formation of hexagonal structural phases α-SiC (6 H -SiC and other) along with the cubic modification of silicon carbide β-SiC. The IR spectroscopy has shown the formation of SiC nanocrystal nuclei due to the energy action of the rf plasma ions on the upper layer of the SiC film during its growth. The data of X-ray reflectometry demonstrate a high density of the films up to 3.59 g/cm^2 as a result of formation of dense C and SiC clusters in the layers under action of the rf plasma.

Substrate Temperature and La0.9Sr0.1Ga0.8Mg0.2O3-δ Electrolyte Film Growth by Radio Frequency Magnetron Sputtering

2015 ◽  
Vol 833 ◽  
pp. 127-133
Author(s):  
Jie Yu ◽  
Jie Xing ◽  
Xiu Hua Chen ◽  
Wen Hui Ma ◽  
Rui Li ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Radio Frequency ◽  
Film Growth ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrolyte Film ◽  
Porous Anode

La0.9Sr0.1Ga0.8Mg0.2O3-δ (LSGM) electrolyte thin films were fabricated on La0.7Sr0.3Cr0.5Mn0.5O2.75 (LSCM) porous anode substrates by Radio Frequency (RF) magnetron sputtering method. The compatibility between LSGM and LSCM was examined. Microstructures of LSGM thin films fabricated were observed by scanning electron microscope (SEM). The effect of substrate temperature on LSGM thin films was clarified by X-ray Diffraction (XRD). Deposition rate increases firstly at the range of 50°C~150°C, and then decreases at the range of 150°C ~300°C. After annealing, perovskite structure with the same growth orientation forms at different substrate temperature. Crystallite size decreases at first, to the minimum point at 150°C, then increases as substrate temperature rises.

Differences between (103) and (002) X-ray diffraction characteristics of nanostructured AZO films deposited by RF magnetron sputtering

2019 ◽  
Vol 372 ◽  
pp. 442-450 ◽  
Author(s):  
I. Cosme ◽  
S. Vázquez-y-Parraguirre ◽  
O. Malik ◽  
S. Mansurova ◽  
N. Carlos ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray

Properties of Nano-ZnO Films Deposited by RF Magnetron Sputtering for SAW Biosensors

2011 ◽  
Vol 418-420 ◽  
pp. 293-296
Author(s):  
Qiu Yun Fu ◽  
Peng Cheng Yi ◽  
Dong Xiang Zhou ◽  
Wei Luo ◽  
Jian Feng Deng
Keyword(s):  
Magnetron Sputtering ◽  
Deposition Time ◽  
Rf Magnetron Sputtering ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Zno Film ◽  
Nano Zno ◽  
Axis Orientation ◽  
X Ray

Abstract. In this article, nano-ZnO films were deposited on SiO2/Si (100) substrates by RF (radio frequency) magnetron sputtering using high purity (99.99%) ZnO target. The effects of deposition time and annealing temperature have been investigated. XRD (X-ray diffraction) and FSEM (Field Emission Scanning Electron Microscopy) were employed to characterize the quality of the films. The results show that the ZnO film with thickness of 600nm annealed at 900°C has higher quality of both C-axis orientation and crystallization. And for the Zone film with thickness of 300nm annealed at 850°C, the quality of both C-axis orientation and crystallization is higher than that annealed at 900°C and 950°C.

Application of V2O5 in Thin Film Microbatteries Prepared by RF Magnetron Sputtering

2009 ◽  
Vol 79-82 ◽  
pp. 931-934 ◽  
Author(s):  
Liang Tang Zhang ◽  
Jie Song ◽  
Quan Feng Dong ◽  
Sun Tao Wu
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Unit Area ◽  
Rf Magnetron Sputtering ◽  
Micro Electro Mechanical System ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mems Technology ◽  
Surface Morphologies ◽  
Sputtering System

The polycrystalline V2O5 films as the anode in V2O5 /LiPON /LiCoO2 lithium microbattary were prepared by RF magnetron sputtering system. The V2O5 films’ crystal structures, surface morphologies and composition were characterized and analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The microbatteries were fabricated by micro electro-mechanical system (MEMS) technology. The battery active unit area is 500μm×500μm, and the thickness of V2O5, LiPON and LiCoO2 films was estimated to be 200, 610, and 220nm, respectively. The discharge volumetric capacity is between 9.36μAhcm-2μm-1 and 9.63μAhcm-2μm-1 after 40 cycles.

Influence of Substrate on Structure and Magnetic Properties of Bi0.9Nd0.1FeO3 Thin Films by Radio Frequency Magnetron Sputtering Method

2013 ◽  
Vol 302 ◽  
pp. 146-150
Author(s):  
L.L. Li ◽  
Qiu Xiang Liu ◽  
Yan Zou ◽  
Xin Gui Tang ◽  
Yan Ping Jiang
Keyword(s):  
Magnetic Properties ◽  
Magnetron Sputtering ◽  
Radio Frequency ◽  
Cross Section ◽  
Rf Magnetron Sputtering ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure Morphology ◽  
Influence Of Substrate

Bi0.9Nd0.1FeO3 (BNFO) films were deposited on Si (100) and (La,Sr)(Al,Ta)O3 (100) (LAST) substrate by radio frequency (RF) magnetron sputtering method respectively. The structure，morphology and magnetic properties were studied. X-ray diffraction (XRD) result indicates that the BNFO films on different substrate adopted different orientation. Cross-section scanning electron microscopy shows that the film thickness is 145 nm．Magnetic properties measurement shows that the film on Si(100) substrate has the larger saturation magnetization (Ms) of 3 686 emu/cm3, while the Ms value of the BNFO films on LSAT(100) substrate is only 1 213 emu/cm3.

Nanometer Coatings of Hydroxyapatite Characterized by Glancing-Incidence X- Ray Diffraction

2008 ◽  
Vol 396-398 ◽  
pp. 369-372 ◽  
Author(s):  
Alexandre Mello ◽  
Elena Mavropoulos ◽  
Zhen Hong ◽  
J.B. Ketterson ◽  
Antonella M. Rossi
Keyword(s):  
Magnetron Sputtering ◽  
Room Temperature ◽  
Structural Information ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
Promising Candidate ◽  
Thin Coatings ◽  
X Ray ◽  
Nano Coating ◽  
Biocompatible Coatings

Hydroxyapatite (HAP) crystalline thin-coatings have been grown using a right angle RF magnetron sputtering approach at room temperature. The surface structural information of these biocompatible coatings at nanometer scales was obtained by glancing-incidence X-ray diffraction (GIXRD) with synchrotron radiation. The GIXRD spectra were obtained by fixed incidence theta angles at 0.5 and 1 degree. Structural profile analyses were performed over these nano-coating layers with reduced substrate interference. The coating thickness was calibrated by specular X-ray reflectivity (XRR) curves. Experiments have been performed on thin-coatings of HAP sputtered on silicon wafers and acid etched titanium discs at room temperature. GIXRD analysis has shown that all the principal peaks are attributed to a crystalline HAP. Previous tests of biocompatibility with osteoblasts cells have been encouraging studies on the surface of hydroxyapatite thin coatings prepared by opposing RF magnetron sputtering approach, as a promising candidate for bioimplant materials.

Investigation on AZO Films Deposited by Radio-Frequency Reactive Magnetron Sputtering

2013 ◽  
Vol 320 ◽  
pp. 35-39
Author(s):  
Cheng Long Kang ◽  
Jin Xiang Deng ◽  
Min Cui ◽  
Chao Man ◽  
Le Kong ◽  
...  
Keyword(s):  
Thin Films ◽  
Electron Microscope ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Rf Magnetron Sputtering ◽  
Reactive Magnetron ◽  
X Ray Diffraction ◽  
X Ray ◽  
Doped Zno ◽  
Scanning Electron

The Al2O3-doped ZnO(AZO) films were deposited on the glasses by means of RF magnetron sputtering technology. The films were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and Profile-system respectively. The effect of substrate temperature on the structure of the AZO films is investigated.As a result, the properties of the AZO thin films are remarkably influenced by the substrate temperature , especially in the range of 200°C to 500 °C. The film prepared at the substrate temperature of 400°C possesses the best crystalline.

Deposition And Characterization of CNx Films

1994 ◽  
Vol 339 ◽  
Author(s):  
X. T. Cui ◽  
Z. H. Zhang ◽  
Q. Y. Chen ◽  
F. Romero-Borja ◽  
J. R. Liu ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Ir Spectroscopy ◽  
Magnetron Sputtering ◽  
Annealing Effect ◽  
Single Bond ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
X Ray ◽  
Bonding Properties

ABSTRACTCNx films with x around 1.0 have been made by inverted cylindrical DC magnetron sputtering. RBS, XPS, IR spectroscopy, ERD and SEM were used to characterize the composition and bonding properties of the films, while X-ray diffraction was used for crystal structure determination. XPS data indicated the existence of the tetrahedral C3N4 phase in the CNx films, which was consistent with the C-N single bond suggested by IR spectra. The annealing effect on CNx films will also be discussed.

Fabrication of ZnO Waveguide Films Deposited on Sapphire and MgO Substrates by RF Magnetron Sputtering

2012 ◽  
Vol 465 ◽  
pp. 155-159
Author(s):  
Feng Xiang Wang ◽  
Jun He Qi ◽  
Fei Lu ◽  
Xi Feng Qin ◽  
Zhao Hong Liu ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Rutherford Backscattering Spectrometry ◽  
Bulk Material ◽  
Stoichiometric Composition ◽  
Rf Magnetron Sputtering ◽  
Waveguide Structure ◽  
Refractive Indices ◽  
X Ray Diffraction ◽  
X Ray ◽  
Grain Sizes

ZnO waveguide films were fabricated on sapphire (001) and MgO (100) substrates by the radiofrequency (RF) magnetron sputtering technology using ZnO ceramic as the target. Properties of the films were investigated by prism coupling method, X-ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS). The results demonstrated that the ZnO nano-films have planar waveguide structure and have nearly stoichiometric composition with c-axis preferred orientation growth. The growth rates of the films were slightly influenced by the substrates. The effective refractive indices of the films were smaller than the bulk material and were affected by substrates. The relationships between the average grain sizes, substrates, and film thickness were analyzed.

Preparation and Characterization of Needle-Like ZnO on TiO2 Nanoparticles by Solution-Immersion Method and RF Magnetron Sputtering

2013 ◽  
Vol 832 ◽  
pp. 596-601 ◽  
Author(s):  
N.A.M. Asib ◽  
Aadila Aziz ◽  
A.N. Afaah ◽  
Mohamad Rusop ◽  
Zuraida Khusaimi
Keyword(s):  
Magnetron Sputtering ◽  
Average Diameter ◽  
Rf Magnetron Sputtering ◽  
Zno Nanostructures ◽  
X Ray Diffraction ◽  
Immersion Method ◽  
X Ray ◽  
Xrd Patterns ◽  
Average Size

Needle-like zinc oxide (ZnO) nanostructures was deposited on titanium dioxide (TiO2) nanoparticles by solution-immersion method and Radio Frequency (RF) magnetron sputtering with diffferent RF powers, respectively on a glass substrate to synthesis nanocomposites of ZnO/TiO2. Field Emission Scanning Electrons Microscope (FESEM) images demonstrate that needle-like ZnO (112-1110 nm) are deposited on the surface of the TiO2nanoparticles with the diameter of approximately 36.3-62.9 nm. At 200 W, more needle-like ZnO with smallest average diameter (112 nm) appeared on the TiO2nanoparticles, which also has the smallest average size of 36.3 nm The compositions of elements in the nanocomposites were showed by Energy Dispersive X-ray Spectrometry (EDX). All elements of Ti, O, and Zn are observed as major components which confirm the presence of TiO2and ZnO in the composite. X-ray Diffraction (XRD) patterns of the nanocomposites show ZnO formed on TiO2nanoparticles are hexagonal with a wurtzite structure and it revealed ZnO/TiO2thin films were succesfully deposited as nanocomposites of ZnTiO3at 100 W,Zn2TiO4at 150 W and Zn2Ti3O8at 200 W and above.

Sign in / Sign up

Export Citation Format

Share Document