scholarly journals Microstructure and mechanical properties of rapidly solidified FeAlCr intermetallic compound

2009 ◽  
Vol 7 (02) ◽  
Author(s):  
R. A. Rodrí­guez-Dí­az ◽  
M. Suárez ◽  
J. Juárez-Islas ◽  
M. G. Garnica-Romo ◽  
J. Arenas-Alatorre ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Electron Microscopy ◽  
Mechanical Properties ◽  
Grain Size ◽  
Intermetallic Compound ◽  
Tensile Tests ◽  
Chemical Analyses ◽  
Melt Spun ◽  
Melt Spun Ribbons ◽  
Rapidly Solidified

In this work results regarding microstructural characterization of a melt‐spun intermetallic compound Fe40Al5Cr (% at.) produced by rapid solidification employing the melt spinning technique at three different tangential wheel speeds (12, 16 and 20 ms‐1) are presented. Melt spun ribbons were characterized by optical and scanning electron microscopy (SEM) in order to observe morphology, grain size, ribbon thickness and also fracture surfaces after tensile tests. EDS coupled to SEM was employed to perform punctual and scan line chemical analyses on samples, x‐ray diffraction (XRD) was utilized to identify crystal structure and phases. Transmission electron microscopy (TEM) was employed to confirm crystal structure and also to characterize nanopores formed in the specimens by vacancy clustering. With regard to mechanical properties, micro hardness Vickers measurements as well as tensile tests at room temperature were applied to the rapidly solidified ribbons.The grain size of rapidly solidified Fe40Al5Cr ribbons suffered a drastic reduction as compared with alloys of the same composition produced by conventional melting and casting methods, and in melt‐spun ribbons it decreases as the wheel speed increases. Punctual and line‐scanning chemical analyses revealed that Cr enters in solid solution in FeAl matrix. Hardness measurements revealed a softening in rapidly solidified FeAlCr ribbons as compared with FeAl alloys and tensile test exhibited a (transgranular + intergranular) mode of fracture, reaching up to 3 % of elongation in FeAlCr alloys. The presence of porous (meso and nano) were also characterized.

scholarly journals Solidification, Microstructure and Mechanical Properties of Mg-2.8Nd-1.5Gd-0.5Zn-0.5Zr Cast Alloy with Erbium Addition

2018 ◽  
Vol 202 ◽  
pp. 01001
Author(s):  
R. Ahmad ◽  
A.M.M. Elaswad ◽  
M. Z. Hamzah ◽  
N. R. Shahizan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Cast Alloy ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Microstructure Analysis ◽  
Cooling Curve ◽  
Scanning Electron

The thermal parameters of Mg-2.8Nd-1.5Gd-0.5Zn-0.5Zr cast alloy with 0.25 wt.% of erbium (Er) were evaluated by the computer-aided cooling curve thermal analysis(CA CCTA), whereas the microstructure analysis was investigated by the optical microscope and scanning electron microscopy. Results from the cooling curve and microstructure analysis showed that Er altered the grain size of the alloys. In addition, the grain size was reduced by approximately 19.6% with the addition of Er. Scanning electron microscopy results showed that Er formed an Mg-Zn-Nd-Er phase which distributed along the grain boundaries. Furthermore, the mechanical properties were investigated by hardness and tensile tests with Er addition. The addition of 0.25 wt.% of Er significantly improved the ultimate tensile strength and yield strength. In addition, the hardness value of Mg-2.8Nd-1.5Gd-0.5Zn-0.5Zr increased by 13.9% with Er addition.

Investigations on Microstructure Evolution and Deformation Behavior of Aged and Ultrafine Grained Al-Zn-Mg Alloy Subjected to Severe Plastic Deformation

2010 ◽  
Vol 667-669 ◽  
pp. 253-258
Author(s):  
Wei Ping Hu ◽  
Si Yuan Zhang ◽  
Xiao Yu He ◽  
Zhen Yang Liu ◽  
Rolf Berghammer ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
Microstructure Evolution ◽  
Deformation Behavior ◽  
Deformation Mechanisms ◽  
Mg Alloy ◽  
Ultrafine Grained

An aged Al-5Zn-1.6Mg alloy with fine η' precipitates was grain refined to ~100 nm grain size by severe plastic deformation (SPD). Microstructure evolution during SPD and mechanical behaviour after SPD of the alloy were characterized by electron microscopy and tensile, compression as well as nanoindentation tests. The influence of η' precipitates on microstructure and mechanical properties of ultrafine grained Al-Zn-Mg alloy is discussed with respect to their effect on dislocation configurations and deformation mechanisms during processing of the alloy.

Influence of Severe Plastic Deformation on the PLC Effect and Mechanical Properties in Al 5XXX Alloy

2006 ◽  
Vol 114 ◽  
pp. 171-176 ◽  
Author(s):  
Joanna Zdunek ◽  
Pawel Widlicki ◽  
Halina Garbacz ◽  
Jaroslaw Mizera ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
True Strain ◽  
Tensile Tests ◽  
Size Reduction ◽  
Hydrostatic Extrusion ◽  
Stress Strain ◽  
Chatelier Effect

In this work, Al-Mg-Mn-Si alloy (5483) in the as-received and severe plastically deformed states was used. Plastic deformation was carried out by hydrostatic extrusion, and three different true strain values were applied 1.4, 2.8 and 3.8. All specimens were subjected to tensile tests and microhardness measurements. The investigated material revealed an instability during plastic deformation in the form of serration on the stress-strain curves, the so called Portevin-Le Chatelier effect It was shown that grain size reduction effected the character of the instability.

Large reversible magnetic entropy change in rapidly solidified Ni0.895Cr0.105MnGe1.05 melt-spun ribbons

2018 ◽  
Vol 97 ◽  
pp. 89-94 ◽  
Author(s):  
Anil Aryal ◽  
Abdiel Quetz ◽  
C.F. Sánchez-Valdés ◽  
P.J. Ibarra-Gaytán ◽  
Sudip Pandey ◽  
...  
Keyword(s):  
Magnetic Entropy Change ◽  
Entropy Change ◽  
Magnetic Entropy ◽  
Melt Spun ◽  
Melt Spun Ribbons ◽  
Rapidly Solidified

scholarly journals Polymeric Composites Based on Polyurea Matrix Reinforced with Carbon Nanotubes

2017 ◽  
Vol 54 (1) ◽  
pp. 41-44 ◽  
Author(s):  
Maria Adina Vulcan ◽  
Celina Damian ◽  
Paul Octavian Stanescu ◽  
Eugeniu Vasile ◽  
Razvan Petre ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Scanning Electron Microscopy ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

This paper deals with the synthesis of polyurea and its use as polymer matrix for nanocomposites reinforced with multi-walled carbon nanotubes (MWCNT). Two types of materials were obtained during this research, the first cathegory uses the polyurea as matrix and the second one uses a mixture between epoxy resin and polyurea. The nanocomposites were characterized by Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM) and Tensile Tests .The elastomeric features of nanocomposites were highlighted by the results which showed low value of Tg. Also higher thermal stability with ~40oC compared with commercial products (M20) were observed, but lower mechanical properties compared to neat polyurea.

New method for the production of bulk amorphous materials of Nd–Fe–B alloys

2005 ◽  
Vol 20 (3) ◽  
pp. 563-566 ◽  
Author(s):  
Tetsuji Saito ◽  
Hiroyuku Takeishi ◽  
Noboru Nakayama
Keyword(s):  
Electron Microscopy ◽  
Amorphous Materials ◽  
Room Temperature ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Bulk Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Melt Spun ◽  
Melt Spun Ribbons

We report a new compression shearing method for the production of bulk amorphous materials. In this study, amorphous Nd–Fe–B melt-spun ribbons were successfully consolidated into bulk form at room temperature by the compression shearing method. X-ray diffraction and transmission electron microscopy studies revealed that the amorphous structure was well maintained in the bulk materials. The resultant bulk materials exhibited the same magnetic properties as the original amorphous Nd–Fe–B materials.

Structure and mechanical properties of Ni/Ti multilayered composites produced by accumulative roll-bonding process

2019 ◽  
Vol 54 (8) ◽  
pp. 1119-1126
Author(s):  
Mohammad Mokhles ◽  
Morteza Hosseini ◽  
Habib Danesh-Manesh ◽  
Seyed Mojtaba Zebarjad
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Accumulative Roll Bonding ◽  
Tensile Tests ◽  
Total Elongation ◽  
Uniaxial Tensile ◽  
Roll Bonding ◽  
Multilayered Composites ◽  
Scanning Electron

This research studies the structure and mechanical properties of Ni/Ti multilayered composites produced from commercial pure Ni and Ti foils by accumulative roll-bonding technique. To investigate these properties, scanning electron microscopy, Vickers microhardness, and uniaxial tensile tests were conducted at different processing cycles. Studies showed that in terms of structure, Ni and Ti layers maintain their continuity even up to 10 cycles of accumulative roll-bonding. Moreover, the energy-dispersive spectroscopy in scanning electron microscopy detected no deformation induced diffusion or reactive interfacial zones. It was found that by increasing the accumulative roll-bonding cycles, tensile and yield strengths as well as the hardness of the composite enhance and the total elongation reduces continuously.

scholarly journals Novel Approach of Nanostructured Bainitic Steels’ Production with Improved Toughness and Strength

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1220
Author(s):  
Peter Kirbiš ◽  
Ivan Anžel ◽  
Rebeka Rudolf ◽  
Mihael Brunčko
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fine Structure ◽  
Retained Austenite ◽  
Bainitic Ferrite ◽  
High Hardness ◽  
Tensile Tests ◽  
Isothermal Transformation ◽  
Impact Testing ◽  
Bainitic Steels

The tendencies of development within the field of engineering materials show a persistent trend towards the increase of strength and toughness. This pressure is particularly pronounced in the field of steels, since they compete with light alloys and composite materials in many applications. The improvement of steels’ mechanical properties is sought to be achieved with the formation of exceptionally fine microstructures ranging well into the nanoscale, which enable a substantial increase in strength without being detrimental to toughness. The preferred route by which such a structure can be produced is not by applying the external plastic deformation, but by controlling the phase transformation from austenite into ferrite at low temperatures. The formation of bainite in steels at temperatures lower than about 200 °C enables the obtainment of the bulk nanostructured materials purely by heat treatment. This offers the advantages of high productivity, as well as few constraints in regard to the shape and size of the workpiece when compared with other methods for the production of nanostructured metals. The development of novel bainitic steels was based on high Si or high Al alloys. These groups of steels distinguish a very fine microstructure, comprised predominantly of bainitic ferrite plates, and a small fraction of retained austenite, as well as carbides. The very fine structure, within which the thickness of individual bainitic ferrite plates can be as thin as 5 nm, is obtained purely by quenching and natural ageing, without the use of isothermal transformation, which is characteristic for most bainitic steels. By virtue of their fine structure and low retained austenite content, this group of steels can develop a very high hardness of up to 65 HRC, while retaining a considerable level of impact toughness. The mechanical properties were evaluated by hardness measurements, impact testing of notched and unnotched specimens, as well as compression and tensile tests. Additionally, the steels’ microstructures were characterised using light microscopy, field emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM). The obtained results confirmed that the strong refinement of the microstructural elements in the steels results in a combination of extremely high strength and very good toughness.

Effect of Fast Annealing on Microstructure and Mechanical Properties of Non-Oriented Al-Si Low C Electrical Steels

2007 ◽  
Vol 560 ◽  
pp. 29-34 ◽  
Author(s):  
Emmanuel Gutiérrez C. ◽  
Armando Salinas-Rodríguez ◽  
Enrique Nava-Vázquez
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Room Temperature ◽  
Tensile Tests ◽  
Rate Of Change ◽  
Uniaxial Tensile ◽  
Electrical Steels ◽  
Offset Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Increasing Temperature

The effects of heating rate and annealing temperature on the microstructure and mechanical properties of cold rolled Al-Si, low C non-oriented electrical steels are investigated using SEM metallography and uniaxial tensile tests. The experimental results show that short term annealing at temperatures up to 850 °C result in microstructures consisting of recrystallized ferrite grains with sizes similar to those observed in industrial semi-processed strips subjected to long term batch annealing treatments. Within the temperature range investigated, the grain size increases and the 0.2% offset yield strength decreases with increasing temperature. It was observed that the rate of change of grain size with increasing temperature increases when annealing is performed at temperatures greater than Ac1 (~870 °C). This effect is attributed to Fe3C dissolution and rapid C segregation to austenite for annealing temperatures within the ferrite+austenite phase field. This leads to faster ferrite growth and formation of pearlite when the steel is finally cooled to room temperature. The presence of pearlite at room temperature decreases the ductility of samples annealed at T > Ac1.

Sign in / Sign up

Export Citation Format

Share Document