scholarly journals Study of the effect of Mg (II) addition and the annealing conditions on the structure of mesoporous aluminum oxide using Plackett-Burman design

2015 ◽  
Vol 80 (12) ◽  
pp. 1529-1540 ◽  
Author(s):  
Tatjana Novakovic ◽  
Ljiljana Rozic ◽  
Srdjan Petrovic ◽  
Zorica Vukovic ◽  
Miodrag Mitric
Keyword(s):  
Specific Surface ◽  
Crystallite Size ◽  
Heating Rate ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Magnesium Nitrate ◽  
Degree Of Crystallinity ◽  
Burman Design ◽  
Plackett Burman Design

A statistical design was used to investigate the effect of various processing conditions on the structure of sol-gel derived Mg(II) doped alumina. Six processing variables were selected based on the Plackett-Burman design: concentration of magnesium nitrate, time and temperature of alcohol evaporation, temperature and time of annealing and heating rate were changed at two levels. For every set of conditions, samples with different specific surface area and degree of crystallinity were obtained. Analysis of the results showed that annealing temperature , heating rate and concentration of magnesium nitrate were the main factors affecting average crystallite size of the predominant phase of alumina. In the case of the specific surface area, two of selected six variables had pronounced effect; however the temperature of annealing was more effective than others. The present results show that the proposed model that uses crystallite size as a response variables is preferable to further research.

Influence of Heat Treatment Process on Properties of Polycrystalline Alumina Fiber

2011 ◽  
Vol 399-401 ◽  
pp. 822-827 ◽  
Author(s):  
Jian Feng Xu ◽  
Shun De Fu ◽  
Ke Zhang
Keyword(s):  
Tensile Strength ◽  
Specific Surface ◽  
Heating Rate ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Polycrystalline Alumina ◽  
Average Tensile Strength ◽  
Alumina Fibers ◽  
Crystalline Growth

Polycrystalline alumina fibers were prepared by sol-gel method. The influence of heating rate on average tensile strength of fibers as well as the influence of calcining temperature on average tensile strength of fibers, crystal phases form, specific surface area of fibers were studied. The results show that when the heating rate (below 600°C) is 4°C/min,the average tensile strength of fibers over 1000Mpa The fibers pulverize obviously when the heating rate＞7°C/min. The average tensile strength and the specific surface area of fibers decreased with calcining temperature rising. When the calcining temperature reaches over 1300°C, the average tensile strength of fibers decreased quickly and the specific surface area of fibers decreases slowly for the crystalline growth.

scholarly journals Influence of the pH Values of the Sol–Gel State on the Properties of SnO2Powders Obtained From a Sol–Gel Route

1995 ◽  
Vol 18 (1) ◽  
pp. 53-60 ◽  
Author(s):  
S. D. Han ◽  
S. Y. Huang ◽  
G. Campet ◽  
M. A. Kennard ◽  
Y. M. Son
Keyword(s):  
Specific Surface ◽  
Crystallite Size ◽  
Surface Area ◽  
Calcination Temperature ◽  
Specific Surface Area ◽  
Ph Value ◽  
Ph Dependence ◽  
Sol Gel ◽  
Ph Values ◽  
Colloidal State

The evolution of the specific surface area and crystallite size of SnO2powders, prepared from a sol-gel process, was studied as a function of the calcination temperature of the stannic hydroxyde colloid, and for two different pH values (7.5 and 12.5) of the colloïdal state. The samples were characterized by TGA, IR spectroscopy, BET, and XRD techniques. The crystallite size and specific surface area were strongly affected not only by the calcination temperature, but unexpectedly, by the initial pH value of the colloïdal state. A framework model, relating the pH dependence to the resulting properties, is presented.

scholarly journals Tuning the Morphological Properties of Cellulose Aerogels: An Investigation of Salt-Mediated Preparation

2021 ◽  
Author(s):  
Prakash Parajuli ◽  
Sanjit Acharya ◽  
Julia Shamshina ◽  
Noureddine Abidi
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Earth Metal ◽  
Morphological Properties ◽  
Cellulose Solution ◽  
Bet Analysis ◽  
Sol Gel Transition ◽  
Gel Transition

Abstract In this study, alkali and alkaline earth metal chlorides with different cationic radii (LiCl, NaCl, and KCl, MgCl2, and CaCl2) were used to gain insight into the behavior of cellulose solutions in the presence of salts. The specific focus of the study was evaluation of the effect of salts’ addition on the sol-gel transition of the cellulose solutions and on their ability to form monoliths, as well as evaluation of the morphology (e.g., specific surface area, pore characteristics, and microstructure) of aerocelluloses prepared from these solutions. The effect of the salt addition on the sol-gel transition of cellulose solutions was studied using rheology, and morphology of resultant aerogels was evaluated by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis, while the salt influence on the aerocelluloses’ crystalline structure and thermal stability was evaluated using powder X-Ray Diffraction (pXRD) and Thermogravimetric Analysis (TGA), respectively. The study revealed that the effect of salts’ addition was dependent on the component ions and their concentration. The addition of salts in the amount below certain concentration limit significantly improved the ability of the cellulose solutions to form monoliths and reduced the sol-gel transition time. Salts of lower cationic radii had a greater effect on gelation. However, excessive amount of salts resulted in the formation of fragile monoliths or no formation of gels at all. Analysis of surface morphology demonstrated that the addition of salts resulted in a significant increase in porosity and specific surface area, with salts of lower cationic radii leading to aerogels with much larger (~1.5 and 1.6-fold for LiCl and MgCl2, respectively) specific surface area compared to aerocelluloses prepared with no added salt. Thus, by adding the appropriate salt into the cellulose solution prior to gelation, the properties of aerocelluloses that control material’s performance (specific surface area, density, and porosity) could be tailored for a specific application.

scholarly journals Synthesis of Spherical Silica by Sol-Gel Method and Its Application as Catalyst Support

2011 ◽  
Vol 10 (2) ◽  
pp. 25
Author(s):  
Anirut Leksomboon ◽  
Bunjerd Jongsomjit
Keyword(s):  
Particle Size ◽  
Ethylene Glycol ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Weight Ratio ◽  
Gel Method ◽  
Sol Gel Method ◽  
Spherical Silica

In this present study, the spherical silica support was synthesized from tetraethyloxysilane (TEOS), water, sodium hydroxide, ethylene glycol and n-dodecyltrimethyl ammonium bromide (C12TMABr). The particle size was controlled by variation of the ethylene glycol co-solvent weight ratio of a sol-gel method preparation in the range of 0.10 to 0.50. In addition, the particle size apparently increases with high weight ratio of co-solvent, but the particle size distribution was broader. The standard deviation of particle diameter is large when the co-solvent weight ratio is more than 0.35 and less than 0.15. However, the specific surface area was similar for all weight ratios ranging from 1000 to 1300 m2/g. The synthesized silica was spherical and has high specific surface area. The cobalt was impregnated onto the obtained silica to produce the cobalt catalyst used for CO2 hydrogenation.</

Photocatalytic Efficiency for Dye Decolorization of the UV/TiO2, UV/TiO2 + In2O3 and UV/TiO2-In2O3 Systems

2013 ◽  
Vol 831 ◽  
pp. 263-266
Author(s):  
Chung Hsin Wu ◽  
Chao Yin Kuo ◽  
Chih Hao Lai ◽  
Wei Yang Chung
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Dye Decolorization ◽  
X Ray Diffraction ◽  
First Order ◽  
First Order Kinetics ◽  
Vis Spectroscopy ◽  
Reactive Red 2

This study explored the decolorization of C.I. Reactive Red 2 (RR2) by the ultraviolet (UV)/TiO2, UV/TiO2 + In2O3, and UV/TiO2-In2O3 systems. The TiO2-In2O3 was generated by the sol-gel method and TiO2 + In2O3 was created by mixing TiO2 and In2O3 powders. The surface properties of TiO2, In2O3, and TiO2-In2O3 were analyzed by X-ray diffraction, a specific surface area analyzer, UV-vis spectroscopy, and scanning electron microscopy. The specific surface area of TiO2, In2O3, and TiO2-In2O3 was 29.5, 44.6, and 35.7 m2/g, respectively; additionally, the band gap of TiO2, In2O3, and TiO2-In2O3 was 2.95, 2.64, and 2.91 eV; respectively. The decolorization rate constant fit pseudo-first-order kinetics and that of the UV/TiO2, UV/TiO2 + In2O3, and UV/TiO2-In2O3 systems was 0.0023, 0.0031, and 0.0072 min-1; respectively.

Study of Heating Effect on Specific Surface Area, and Changing Optical Properties of ZnO Nanocrystals

2011 ◽  
Vol 403-408 ◽  
pp. 1205-1210
Author(s):  
Jaleh Babak ◽  
Ashrafi Ghazaleh ◽  
Gholami Nasim ◽  
Azizian Saeid ◽  
Golbedaghi Reza ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Energy Gap ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zno Nanocrystals ◽  
Transmission Electron ◽  
Zno Nanocrystal

In this work ZnO nanocrystal powders have been synthesized by using Zinc acetate dehydrate as a precursor and sol-gel method. Then the products have been annealed at temperature of 200-1050°C, for 2 hours. The powders were characterized using X-ray diffraction (XRD), UV-vis absorption and photoluminescence (PL) spectroscopy. The morphology of refrence ZnO nanoparticles have been studied using Transmission Electron Microscope (TEM). During the annealing process, increase in nanocrystal size, defects and energy gap quantitative, and decrease in specific surface area have been observed.

Bi2WO6 Nanoparticles Prepared by Combustion Synthesis with Different Fuels and their Photocatalytic Activity

2014 ◽  
Vol 604 ◽  
pp. 93-101
Author(s):  
Maris Kodols ◽  
Sabine Didrihsone ◽  
Janis Grabis
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Citric Acid ◽  
Ethylene Glycol ◽  
Specific Surface ◽  
Crystallite Size ◽  
Combustion Synthesis ◽  
Surface Area ◽  
Specific Surface Area ◽  
Solution Ph

The influence of glycine, glycerine, ethylene glycol and citric acid fuel and their ratio to NO3- on formation and dispersity of Bi2WO6 nanoparticles prepared by combustion synthesis has been studied. The pure crystalline Bi2WO6 with specific surface area 24,8 m2/g and crystallite size of 28 nm was obtained by using glycerine as fuel at its ratio to NO3- of 0,67. The photocatalytic activity of the prepared Bi2WO6 in degradation of methylene blue depended on its specific surface area of samples and solution pH.

Sign in / Sign up

Export Citation Format

Share Document