scholarly journals Bioglass-fibre reinforced hydroxyapatite composites synthesized using spark plasma sintering for bone tissue engineering

2021 ◽  
Vol 15 (3) ◽  
pp. 270-278
Author(s):  
Muhammad Rizwan ◽  
Ali Chandio ◽  
Muhammad Sohail ◽  
Nasir Bashir ◽  
Sumra Yousuf ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Bone Scaffold ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Microscopy Images ◽  
Selection Of

Hydroxyapatite (HA) exhibits several desirable characteristics, but it still lacks osteoinduction, which is a necessary requirement for a bone scaffold. HA-based composites with different amounts of Bioglass? (BG) were prepared using spark plasma sintering (SPS). Careful selection of the SPS parameters avoided undesirable reactions between the calcium phosphate (CaP) and bioglass (BG present in the form of powder and fibres), as confirmed through X-ray diffraction analysis. Scanning electron microscopy images of the composite scaffolds revealed a fibre like appearance of the glassy region. The in vitro bioactivity and biodegradation analyses were performed by immersing the composites in simulated body fluid (SBF) and tris(hydroxymethyl)aminomethane (Tris), respectively. The ability to obtain only the CaP phase and glassy phase with desirable bioactive and biodegradation behaviour, indicated that these SPS scaffolds can be employed as bone scaffolds for clinical trials, after further in vivo analyses.

Development of WC-Fe3Al Composites by Spark Plasma Sintering Process

2016 ◽  
Vol 881 ◽  
pp. 307-312
Author(s):  
Luis Antonio C. Ybarra ◽  
Afonso Chimanski ◽  
Sergio Gama ◽  
Ricardo A.G. da Silva ◽  
Izabel Fernanda Machado ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Zinc Stearate ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Al Composite ◽  
Spark Plasma ◽  
Short Time ◽  
Vibration Mill

Tungsten carbide (WC) based composites are usually produced with cobalt, but this binder has the inconvenience of shortage, unstable price and potential carcinogenicity. The objective of this study was to develop WC composite with intermetallic Fe3Al matrix. Powders of WC, iron and aluminum, with composition WC-10 wt% Fe3Al, and 0.5 wt% zinc stearate were milled in a vibration mill for 6 h and sintered in a SPS (spark plasma sintering) furnace at 1150 °C for 8 min under pressure of 30 MPa. Measured density and microstructure analysis showed that the composite had significant densification during the (low-temperature, short time) sintering, and X-ray diffraction analysis showed the formation of intermetallic Fe3Al. Analysis by Vickers indentation resulted in hardness of 11.2 GPa and fracture toughness of 24.6 MPa.m1/2, showing the feasibility of producing dense WC-Fe3Al composite with high mechanical properties using the SPS technique.

Spark Plasma Sintering of Ti-4.5Al-3V-2Fe-2Mo (SP-700)

2010 ◽  
Vol 654-656 ◽  
pp. 819-822
Author(s):  
Genki Kikuchi ◽  
Hiroshi Izui ◽  
Yuya Takahashi ◽  
Shota Fujino
Keyword(s):  
Spark Plasma Sintering ◽  
Room Temperature ◽  
Volume Fraction ◽  
Titanium Boride ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tib2 Particles

In this study, we focused on the sintering performance of Ti-4.5Al-3V-2Mo-2Fe (SP-700) and mechanical properties of SP-700 reinforced with titanium boride (TiB/SP-700) fabricated by spark plasma sintering (SPS). TiB whiskers formed in titanium by a solid-state reaction of titanium and TiB2 particles were analyzed with scanning electron microscopy and X-ray diffraction. The TiB/SP-700 was sintered at temperatures of 1073, 1173, and 1273 K and a pressure of 70 MPa for 10, 30, and 50 min. The volume fraction of TiB ranged from 1.7 vol.% to 19.9 vol.%. Tensile tests of TiB/SP-700 were conducted at room temperature, and the effect of TiB volume fraction on the tensile properties was investigated.

Spark Plasma Sintering of Paper-Derived Ti3AlC2-Based Composites: Influence of Sintering Temperature

2021 ◽  
Vol 1016 ◽  
pp. 1790-1796
Author(s):  
Maxim Syrtanov ◽  
Egor Kashkarov ◽  
Tatyana Murashkina ◽  
Nahum Travitzky
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Total Content ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carbide Phases ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

This paper describes the influence of sintering temperature on phase composition and microstructure of paper-derived Ti3AlC2 composites fabricated by spark plasma sintering. The composites were sintered at 100 MPa pressure in the temperature range of 1150-1350 °C. Phase composition and microstructure were analyzed by X-ray diffraction and scanning electron microscopy, respectively. The multiphase structure was observed in the sintered composites consisting of Ti3AlC2, Ti2AlC, TiC and Al2O3 phases. The decomposition of the Ti3AlC2 phase into Ti2AlC and TiC carbide phases was observed with temperature rise. The total content of Ti3AlC2 and Ti2AlC phases was reduced from 84.5 vol.% (1150 °C) to 69.5 vol.% (1350 °C). The density of composites affected by both the content of TiC phase and changes in porosity.

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

2016 ◽  
Vol 704 ◽  
pp. 183-189
Author(s):  
Yong Jun Su ◽  
Yi Feng Zheng ◽  
De Liang Zhang ◽  
Fan Tao Kong
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Tial Alloy ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Short Period ◽  
Spark Plasma ◽  
Fully Lamellar

TiAl alloy with a composition of Ti-43Al-5V-4Nb-Y (at.%) was prepared by spark plasma sintering (SPS). The TiAl powders were sintered between 650°C and 1300°C for 5 min under different loads. With the increasing of the temperature, the diffusion of the elements can be observed. Full compaction is achieved in a short period of time and the overall processing duration does not exceed 30 min. A fully lamellar structure was seen in the TiAl alloy after heat treatment. The microstructures of the samples were determined by X-ray diffraction and scanning electron microscopy. Their mechanical properties were evaluated by tensile tests performed at room temperature

Solid-State Synthesis of Magnesium Silicide via Repeated Plastic Working and Spark Plasma Sintering

2005 ◽  
Vol 475-479 ◽  
pp. 2895-2898
Author(s):  
Hideki Oginuma ◽  
Katsuyoshi Kondoh ◽  
Takashi Yamaguchi ◽  
Eiji Yuasa
Keyword(s):  
Solid State ◽  
Spark Plasma Sintering ◽  
Bulk Material ◽  
Magnesium Silicide ◽  
X Ray Diffraction ◽  
Plastic Working ◽  
X Ray ◽  
Plasma Sintering ◽  
Elemental Powder Mixture ◽  
Spark Plasma

In this study, the solid-state reaction to form Mg2Si bulky materials via spark plasma sintering (SPS) process was discussed. Elemental powder mixture of Mg-33.33mol%Si was refined and consolidated as green compacts by repeated plastic working (RPW) SPS was performed to synthesize and sinter magnesium silicide at 1100K from the RPWed compact. The only peaks of Mg2Si, not Mg and Si, were detected by X-ray diffraction analysis. Mg2Si bulky intermetallic began to shrink above 800K during SPS process, and its densification significantly occurred. The density of SPSed Mg2Si bulk material is about 100% of the theoretically relative one.

THE GROWTH OF MnSi1.73 PREPARED BY SPARK PLASMA SINTERING

2004 ◽  
Vol 18 (01) ◽  
pp. 87-93 ◽  
Author(s):  
ZHIMIN WANG ◽  
YIDONG WU ◽  
YUANJIN HE
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Spark Plasma Sintering ◽  
X Ray Diffraction ◽  
Mechanical Pressure ◽  
Growth Processes ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

Crystals of MnSi 1.73 were prepared by Spark Plasma Sintering (SPS) technique, analyzed by X-ray diffraction (XRD), and invested by metalogragh and scanning electron microscopy (SEM). The growth processes of the samples were studied. It was found that the Mn–Si powders partly formed MnSi 1.73 crystals at 912–937 K under the mechanical pressure of 20 MPa in low vacuum (about 5.0 Pa), and fully formed MnSi 1.73 crystals after sintered at 1173 K for 15 minutes under 40 MPa.

Effect of cryogenic milling on Al7075 prepared by spark plasma sintering method

2017 ◽  
Vol 32 (S1) ◽  
pp. S221-S224 ◽  
Author(s):  
Frantisek Lukac ◽  
Tomas Chraska ◽  
Orsolya Molnarova ◽  
Premysl Malek ◽  
Jakub Cinert
Keyword(s):  
Spark Plasma Sintering ◽  
Rietveld Analysis ◽  
Deformation Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cryogenic Milling ◽  
Plasma Sintering ◽  
Crystallite Sizes ◽  
Spark Plasma ◽  
Sintering Method

Precipitation of secondary intermetallic phases in aluminium alloy Al7075 sintered by spark plasma sintering method from powders milled at room and cryogenic temperature was studied by X-ray powder diffraction. Deformation energy stored during cryogenic milling influences the precipitation in Al7075 alloy. High temperature X-ray diffraction experiment revealed the potential for further precipitation strengthening of samples prepared by spark plasma sintering of milled powders. It was established that the correction of absorption edge of metal Kβ-line filter used for laboratory sources greatly enhances the precision of quantitative Rietveld analysis as well as the determination of precipitates’ crystallite sizes.

Creep Deformation of 10 mol% La2O3 + YSZ Ceramic Composite Prepared by Spark Plasma Sintering

2014 ◽  
Vol 783-786 ◽  
pp. 1087-1092
Author(s):  
Karen D. Robles-Arellano ◽  
Lukas Bichler
Keyword(s):  
Spark Plasma Sintering ◽  
Ceramic Composite ◽  
Grain Boundary Sliding ◽  
Lattice Diffusion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Boundary Sliding ◽  
Potential Use

Development of creep-resistant 8mol% Yttria-stabilized Zirconia (YSZ) ceramic has received much interest due to its potential use in fuel cells and thermal barrier coatings. In this research, Spark Plasma Sintering was used to develop a high-density 10 mol% La203 + YSZ composite. Compressive creep testing was performed at 1300 oC at 45 – 78 MPa load. The mechanism of plastic deformation of the composite was studied using Scanning Electron Microscopy and X-Ray Diffraction. The results suggest that lattice diffusion and grain boundary sliding were the active creep mechanisms.

Fabrication of Mg2Si Thermoelectric Materials by Mechanical Alloying and Spark-Plasma Sintering Process

2006 ◽  
Vol 6 (11) ◽  
pp. 3429-3432
Author(s):  
Chung-Hyo Lee ◽  
Seong-Hee Lee ◽  
Sung-Yong Chun ◽  
Sang-Jin Lee
Keyword(s):  
Grain Size ◽  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Room Temperature ◽  
Atomic Ratio ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma

A mixture of pure Mg and Si powders with an atomic ratio 2:1 has been subjected to mechanical alloying (MA) at room temperature to prepare the Mg2Si thermoelectric material. Mg2Si intermetallic compound with a grain size of 50 nm can be obtained by MA of Mg66.7Si33.3 powders for 60 hours and subsequently annealed at 620 °C. Consolidation of the MA powders was performed in a spark plasma sintering (SPS) machine using graphite dies up to 800–900 °C under 50 MPa. The shrinkage of consolidated samples during SPS was significant at about 250 °C and 620 °C. X-ray diffraction data shows that the SPS compact from 60 h MA powders consolidated up to 800 °C consists of only nanocrystalline Mg2Si compound with a grain size of 100 nm.

Fabrication of Ti-Based Biodegradable Material Composites Prepared by Spark Plasma Sintering Method

2010 ◽  
Vol 654-656 ◽  
pp. 2158-2161 ◽  
Author(s):  
Eri Miura-Fujiwara ◽  
Takeshi Teramoto ◽  
Hisashi Sato ◽  
Equo Kobayashi ◽  
Yoshimi Watanabe
Keyword(s):  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Holding Time ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Porous Ti ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Sintering Method

This study aims at producing porous Ti filled with biodegradable materials for biomedical implants by means of spark plasma sintering method (SPS). To improve bone fixation and to obtain appropriate Young’s modulus as a medical implant material, we applied -tri calcium phosphate (-TCP) to the Ti-based composite. Ti/-TCP powder mixtures were sintered by SPS under applied stress of 45MPa with various temperatures and holding time. Vickers hardness (Hv) of obtained composite increased with increasing the holding time up to 10 min, and saturated hardness was approximately 750 Hv, which is extremely higher than that of bulk Ti. Hardness also increased as sintering temperature increased up to 1473 K. From the results of microstructure observations by scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDXS), O- and P- containing Ti surrounded around Ti particle, and O diffused into Ti particle to a certain extent. X-ray diffraction results indicated several kinds of Ti-O and/or Ti-P formed in the specimen. Results indicated that it is the brittle phases formed during sintering that increased the hardness.

Sign in / Sign up

Export Citation Format

Share Document