scholarly journals Investigation of zinc stannate synthesis using photoacoustic spectroscopy

2007 ◽  
Vol 39 (2) ◽  
pp. 153-160 ◽  
Author(s):  
T. Ivetic ◽  
M.V. Nikolic ◽  
P.M. Nikolic ◽  
V. Blagojevic ◽  
S. Djuric ◽  
...  
Keyword(s):  
Thermal Diffusivity ◽  
Ball Mill ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
X Ray ◽  
Microstructure Characteristics ◽  
Amplitude Spectra ◽  
Scanning Electron

Mixtures of ZnO and SnO2 powders, with molar ratio of 2:1, were mechanically activated for 40, 80 and 160 minutes in a planetary ball mill. The resulting powders were compacted into pellets and non-isothermally sintered up to 1200?C with a heating rate of 5?C/min. X-ray diffraction analysis of obtained powders and sintered samples was performed in order to investigate changes of the phase composition. The microstructure of sintered samples was examined by scanning electron microscopy. The photoacoustic phase and amplitude spectra of sintered samples were measured as a function of the laser beam modulating frequency using a transmission detection configuration. Fitting of experimental data enabled determination of photoacoustic properties including thermal diffusivity. Based on the results obtained a correlation between thermal diffusivity and experimental conditions as well the samples microstructure characteristics was discussed. .

scholarly journals Synthesis of barium-zinc-titanate ceramics

2012 ◽  
Vol 44 (1) ◽  
pp. 65-71 ◽  
Author(s):  
N. Obradovic ◽  
M.V. Nikolic ◽  
N. Nikolic ◽  
S. Filipovic ◽  
M. Mitric ◽  
...  
Keyword(s):  
Thermal Diffusivity ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Zinc Titanate ◽  
X Ray ◽  
Microstructure Characteristics ◽  
Amplitude Spectra ◽  
Titanate Ceramics

Mixtures of BaCO3, ZnO and TiO2 powders, with molar ratio of 1:2:4, were mechanically activated for 20, 40 and minutes in a planetary ball mill. The resulting powders were compacted into pellets and isothermally sintered at 1250?C for 2h with a heating rate of 10?C/min. X-ray diffraction analysis of obtained powders and sintered samples was performed in order to investigate changes of the phase composition. The microstructure of sintered samples was examined by scanning electron microscopy. The photoacoustic phase and amplitude spectra of sintered samples were measured as a function of the laser beam modulating frequency using a transmission detection configuration. Fitting of experimental data enabled determination of photoacoustic properties including thermal diffusivity. Based on the results obtained correlation between thermal diffusivity and experimental conditions, as well the samples microstructure characteristics, was discussed.

scholarly journals Influence of Bi2O3 on microstructure and electrical properties of ZnO-SnO2 ceramics

2007 ◽  
Vol 39 (3) ◽  
pp. 229-240 ◽  
Author(s):  
T. Ivetic ◽  
M.V. Nikolic ◽  
M. Slankamenac ◽  
M. Zivanov ◽  
D. Minic ◽  
...  
Keyword(s):  
Electrical Properties ◽  
Ball Mill ◽  
Energy Dispersive Spectrometer ◽  
Molar Ratio ◽  
Dc Resistivity ◽  
Impedance Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Scanning Electron

The effects of small amounts (0.5; 1.0 and 1.5 mol. %) of bismuth oxide on the microstructure and electrical properties of ZnO-SnO2 ceramics have been studied. Starting powders of ZnO and SnO2 were mixed in the molar ratio 2:1. After adding Bi2O3 this mixture was mechanically activated for 10 minutes in a planetary ball mill, uniaxially pressed and sintered at 1300?C for 2h. The phase composition of the sintered samples was analyzed by X-Ray Diffraction (XRD) and by Energy Dispersive Spectrometer (EDS). Morphologies were examined by Scanning Electron Microscopy (SEM). An Impedance/Gain Phase Analyzer (HP 4194A) was used to measure the impedance spectra (100Hz - 10MHz) at different temperatures. The electrical DC resistivity/conductivity at different temperatures was measured using a High Resistance Meter (HP 4329A).

Sem and X-Ray Analysis of Renal and Biliary Calculi

1976 ◽  
Vol 34 ◽  
pp. 306-307
Author(s):  
R. J. Narconis ◽  
G. L. Johnson
Keyword(s):  
Chemical Constituents ◽  
Natural State ◽  
X Ray Diffraction ◽  
Chemical Methods ◽  
X Ray ◽  
Additional Dimension ◽  
Biliary Calculi ◽  
Calculus Formation ◽  
Scanning Electron

Analysis of the constituents of renal and biliary calculi may be of help in the management of patients with calculous disease. Several methods of analysis are available for identifying these constituents. Most common are chemical methods, optical crystallography, x-ray diffraction, and infrared spectroscopy. The application of a SEM with x-ray analysis capabilities should be considered as an additional alternative.A scanning electron microscope equipped with an x-ray “mapping” attachment offers an additional dimension in its ability to locate elemental constituents geographically, and thus, provide a clue in determination of possible metabolic etiology in calculus formation. The ability of this method to give an undisturbed view of adjacent layers of elements in their natural state is of advantage in determining the sequence of formation of subsequent layers of chemical constituents.

Application of vermiculite and limestone to desulphurization and to the removal of dust during briquette combustion

2003 ◽  
Vol 67 (6) ◽  
pp. 1243-1251 ◽  
Author(s):  
A. Lu ◽  
D. Zhao ◽  
J. Li ◽  
C. Wang ◽  
S. Qin
Keyword(s):  
Electron Microscopy ◽  
Coal Combustion ◽  
Combustion Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Retention Ratio ◽  
X Ray ◽  
Major Factors ◽  
Chemical Reactant ◽  
Scanning Electron

AbstractSmall domestic cooking furnaces are widely used in China. These cooking furnaces release SO2 gas and dust into the atmosphere and cause serious air pollution. Experiments were conducted to investigate the effects of vermiculite, limestone or CaCO3, and combustion temperature and time on desulphurization and dust removal during briquette combustion in small domestic cooking furnaces. Additives used in the coal are vermiculite, CaCO3 and bentonite. Vermiculite is used for its expansion property to improve the contact between CaCO3 and SO2 and to convey O2 into the interior of briquette; CaCO3 is used as a chemical reactant to react with SO2 to form CaSO4; and bentonite is used to develop briquette strength. Expansion of vermiculite develops loose interior structures, such as pores or cracks, inside the briquette, and thus brings enough oxygen for combustion and sulphation reaction. Effective combustion of the original carbon reduces amounts of dust in the fly ash. X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray analysis show that S exists in the ash only as anhydrite CaSO4, a product of SO2 reacting with CaCO3 and O2. The formation of CaSO4 effectively reduces or eliminates SO2 emission from coal combustion. The major factors controlling S retention are vermiculite, CaCO3 and combustion temperature. The S retention ratio increases with increasing vermiculite amount at 950°C. The S retention ratio also increases with increasing Ca/S molar ratio, and the best Ca/S ratio is 2-3 for most combustion. With 12 g of the original coal, 1 to 2 g of vermiculite, a molar Ca/S ratio of 2.55 by adding CaCO3, and some bentonite, a S retention ratio >65% can be readily achieved. The highest S retention ratio of 97.9% is achieved at 950°C with addition of 2 g of vermiculite, a Ca/S ratio of 2.55 and bentonite.

Structural Evaluation of Ti-22.2Si-11.1B Powders Milled with PCA Addition

2008 ◽  
Vol 591-593 ◽  
pp. 147-153
Author(s):  
Gilbert Silva ◽  
Erika Coaglia Trindade Ramos ◽  
N.S. da Silva ◽  
Alfeu Saraiva Ramos
Keyword(s):  
Electron Microscopy ◽  
Ball Milling ◽  
Ball Mill ◽  
Milling Process ◽  
Argon Atmosphere ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structural Evaluation ◽  
Equilibrium Structures ◽  
Scanning Electron

A large amount of the Ti6Si2B compound can be formed by mechanical alloying and subsequent heat treatment from the elemental Ti-22.2at%Si-11.1at%B powder mixture, but the yield powder after ball milling is reduced due to an excessive agglomeration of ductile particles on the balls and vial surfaces. This work reports on the structural evaluation of Ti-22.2at%Si-11.1at%B powders milled with PCA addition, varying its amount between 1 and 2 wt-%. The milling process was carried out in a planetary ball mill under argon atmosphere, and the milled powders were then heated at 1200oC for 1h under Ar atmosphere in order to obtain equilibrium structures. Samples were characterized by X-ray diffraction, scanning electron microscopy, and thermal analysis. Results revealed that the PCA addition reduced the excessive agglomeration during the ball milling of Ti-22.2at-%Si-11.1at-%B powders. After heating at 1200oC for 1h, the Ti5Si3, Ti3O and/or Ti2C phases were preferentially formed in Ti-22.2at%Si-11.1at%B powders milled with PCA addition, and the Ti6Si2B formation was inhibited.

Synthesis of Precipitate Calcium Carbonate with Variation Morphology from Limestone by Using Solution Mixing Method

2019 ◽  
Vol 966 ◽  
pp. 200-203
Author(s):  
Zaenal Arifin ◽  
Triwikantoro ◽  
Bintoro Anang Subagyo ◽  
Mochamad Zainuri ◽  
Darminto
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Carbonate ◽  
Molar Ratio ◽  
Mixing Process ◽  
X Ray Diffraction ◽  
Precipitate Calcium Carbonate ◽  
X Ray ◽  
Mixing Method ◽  
Scanning Electron

Abstract. In this study, the CaCO3 powder has been successfully synthesized by mixing CaCl2 from natural limestone and Na2CO3 in the same molar ratio. The mixing process of solutions was carried out by employing the molar contents of 0.125, 0.25, 0.375 and 0.5M at varying temperatures of 30, 40, 60 and 80ᴼC. The produced CaCO3 microparticles were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The highest content of aragonite phase with morphology rod-like of the samples is around 29 wt%, resulting from the process using solution of 0.125 M at 80 ᴼC. While at 30 ᴼC and 40 ᴼC produced 100 wt% calcite phase.

scholarly journals Effect of LiNO3 on Expansion of Alkali–Silica Reaction in Rock Prisms and Concrete Microbars Prepared by Sandstone

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1150 ◽  
Author(s):  
Jinxin Liu ◽  
Lanqing Yu ◽  
Min Deng
Keyword(s):  
Electron Microscope ◽  
Critical Concentration ◽  
Stress Test ◽  
Molar Ratio ◽  
Alkali Silica Reaction ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Long Period ◽  
Scanning Electron

The aim of this research is to investigate the effect of LiNO3 on the alkali–silica reaction (ASR) expansion of reactive sandstone and the mechanism through which this occurs. This paper presents the results from tests carried out on rock prisms and concrete microbars prepared by sandstone and LiNO3. The findings show that LiNO3 does not decrease the expansion of these samples unless the molar ratio of [Li]/[Na + K] exceeds 1.66, and the expansion is greatly increased when its concentration is below this critical concentration. The expansion stress test proves that Li2SiO3 is obviously expansive. X-ray diffraction (XRD) and scanning electron microscope (SEM) results indicate that LiNO3 reacts with the microcrystalline quartz inside sandstone, inhibiting the formation of ASR gel, and the formation of Li2SiO3 causes larger expansion. A high concentration of LiNO3 might inhibit the ASR reaction in the early stages, and the formation of Li2SiO3 causes expansion and cracks in concrete after a long period of time.

Synthesis and Comparison of Boron Nitride Nanostructure Prepared on Silicon and Molybdenum Substrates by Laser Plasma Deposition Technique

2011 ◽  
Vol 1307 ◽  
Author(s):  
M. Sajjad ◽  
H. X. Zhang ◽  
P. X. Feng
Keyword(s):  
Electron Microscopy ◽  
Boron Nitride ◽  
Plasma Deposition ◽  
Nitrogen Concentration ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
X Ray ◽  
Si Substrates ◽  
Scanning Electron

ABSTRACTThe synthesis of boron nitride nanowires on silicon (Si) and nanorods on molybdenum (Mo) substrates at the same experimental conditions was composed. Fine tip nanowires with diameters around 50 nm were produced on Si substrates, whereas, nanorods with diameter around 100 nm were formed on Mo substrates. The change in length from 5 μm to 100 μm for nanowires and 0.2 μm to 0.8μm for nanorods following variation of substrate temperature were studied systematically.Scanning Electron Microscopy was used to analyze the surface images of BN nanowires and nanorods. Energy Dispersive X-Ray spectroscopy (EDS) was used to analyze boron and nitrogen concentration in the samples. The crystal structures of BN samples were investigated using Raman spectroscopy and x-ray diffraction. The experimental results showed that the nanorods are hexagonal mixed with cubic, whereas the nanowires are hexagonal.

Study of an Energetic-oxidant Co-crystal: Preparation, Characterisation, and Crystallisation Mechanism

2017 ◽  
Vol 67 (5) ◽  
pp. 510 ◽  
Author(s):  
Han Gao ◽  
Wei Jiang ◽  
Jie Liu ◽  
Gazi Hao ◽  
Lei Xiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Diffraction Spectrum ◽  
Solvent Evaporation Method ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

<p>An energetic co-crystal consisting of the most promising military explosive 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and the most well-known oxidant applied in propellants ammonium perchlorate has been prepared with a simple solvent evaporation method. Scanning electron microscopy revealed that the morphology of co-crystal differs greatly from each component. The X-ray diffraction spectrum, FTIR, Raman spectra, and differential scanning calorimetry characterisation further prove the formation of the co-crystal. The result of determination of hygroscopic rate indicated the hygroscopicity was effectively reduced. At last, the crystallisation mechanism has been discussed.</p>

Morphology and Phase Composition of Sol-Gel Derived Aluminum Borate Nanowhiskers

2015 ◽  
Vol 659 ◽  
pp. 121-126 ◽  
Author(s):  
Pat Sooksaen
Keyword(s):  
Fourier Transform ◽  
Phase Composition ◽  
Sol Gel ◽  
Molar Ratio ◽  
Aluminum Borate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Higher Temperature ◽  
Sol Gel Synthesis ◽  
Scanning Electron

Aluminium borate nanowhiskers with varying aspect ratio were synthesized via sol–gel synthesis. The morphology of aluminum borate (Al4B2O9 and Al18B4O33) nanowhiskers could be controlled by varying the aluminum to boron (Al:B) molar ratio in the sol–gel derived precursors. Sintering temperatures (850 and 1100°C) and sintering times (4 and 32 hours) also affected the phase composition and size of the nanowhiskers. Citric acid was also added in the sol–gel derived precursors as a surface stabilizer for obtaining uniform finely dispersed nanostructures. Fine nanowhiskers were obtained by the calcination at 850°C, whereas higher temperature of 1100°C led to thicker and longer nanowhiskers and became rod-like crystals. The morphology and phase composition were investigated by field emission scanning electron microscope and X-ray diffraction. Chemical bond vibrations in the synthesized nanowhiskers were investigated by Fourier-transform infrared spectroscopy.

Sign in / Sign up

Export Citation Format

Share Document