scholarly journals Effects of heat sink compounds on contact resistance of porous media

2007 ◽  
Vol 11 (4) ◽  
pp. 113-124 ◽  
Author(s):  
Olukayode Akinyemi ◽  
Thomas Sauer
Keyword(s):  
Thermal Conductivity ◽  
Porous Media ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Contact Resistance ◽  
Heat Sink ◽  
Thermal Probe ◽  
Dry Conditions ◽  
Thermal Grease ◽  
Water Contents

High and low-conductivity heat sink compounds were applied in succession on a thermal probe, which was then used to determine the thermal conductivity and thermal diffusivity of some porous media at room temperature. The experiment was conducted separately under different packing densities and water contents to see the effects of the heat sink compounds on the thermal properties at such conditions. High conductivity grease increased the values of thermal conductivity considerably and thus reduces the contact resistance, with increase in bulk density at air-dry conditions, but had virtually no effects on its thermal diffusivity. It however decreased both the thermal conductivity and thermal diffusivity with water content increment. The thermal properties obtained without thermal grease vary considerably from those with the heat sink compounds as water was being applied. The variation however reduced also considerably towards saturation.

Thermal Characterization of Carbon-Carbon Composites

2011 ◽  
Author(s):  
Messiha Saad ◽  
Darryl Baker ◽  
Rhys Reaves
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Critical Role ◽  
Carbon Composite ◽  
Flash Method ◽  
Carbon Composites ◽  
Energy Storage Devices ◽  
Graphitized Carbon

Thermal properties of materials such as specific heat, thermal diffusivity, and thermal conductivity are very important in the engineering design process and analysis of aerospace vehicles as well as space systems. These properties are also important in power generation, transportation, and energy storage devices including fuel cells and solar cells. Thermal conductivity plays a critical role in the performance of materials in high temperature applications. Thermal conductivity is the property that determines the working temperature levels of the material, and it is an important parameter in problems involving heat transfer and thermal structures. The objective of this research is to develop thermal properties data base for carbon-carbon and graphitized carbon-carbon composite materials. The carbon-carbon composites tested were produced by the Resin Transfer Molding (RTM) process using T300 2-D carbon fabric and Primaset PT-30 cyanate ester. The graphitized carbon-carbon composite was heat treated to 2500°C. The flash method was used to measure the thermal diffusivity of the materials; this method is based on America Society for Testing and Materials, ASTM E1461 standard. In addition, the differential scanning calorimeter was used in accordance with the ASTM E1269 standard to determine the specific heat. The thermal conductivity was determined using the measured values of their thermal diffusivity, specific heat, and the density of the materials.

Adhesive penetration of wood cell walls investigated by scanning thermal microscopy (SThM)

Holzforschung ◽  
2008 ◽  
Vol 62 (1) ◽  
pp. 91-98 ◽  
Author(s):  
Johannes Konnerth ◽  
David Harper ◽  
Seung-Hwan Lee ◽  
Timothy G. Rials ◽  
Wolfgang Gindl
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Surface Temperature ◽  
Cell Walls ◽  
Adhesive Contact ◽  
Wood Adhesive ◽  
Bond Line ◽  
Scanning Thermal Microscopy ◽  
Thermal Probe ◽  
Thermal Microscopy

Abstract Cross sections of wood adhesive bonds were studied by scanning thermal microscopy (SThM) with the aim of scrutinizing the distribution of adhesive in the bond line region. The distribution of thermal conductivity, as well as temperature in the bond line area, was measured on the surface by means of a nanofabricated thermal probe offering high spatial and thermal resolution. Both the thermal conductivity and the surface temperature measurements were found suitable to differentiate between materials in the bond region, i.e., adhesive, cell walls and embedding epoxy. Of the two SThM modes available, the surface temperature mode provided images with superior optical contrast. The results clearly demonstrate that the polyurethane adhesive did not cause changes of thermal properties in wood cell walls with adhesive contact. By contrast, cell walls adjacent to a phenol-resorcinol-formaldehyde adhesive showed distinctly changed thermal properties, which is attributed to the presence of adhesive in the wood cell wall.

Experimental Study on Thermal Properties of Hollow Sphere Structures

2021 ◽  
Vol 407 ◽  
pp. 185-191
Author(s):  
Josef Tomas ◽  
Andreas Öchsner ◽  
Markus Merkel
Keyword(s):  
Thermal Conductivity ◽  
Experimental Study ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Hollow Sphere ◽  
Plane Source ◽  
Source Method ◽  
Transient Plane Source ◽  
Transient Plane Source Method

Experimental analyses are performed to determine thermal conductivity, thermal diffusivity and volumetric specific heat with transient plane source method on hollow sphere structures. Single-sided testing is used on different samples and different surfaces. Results dependency on the surface is observed.

scholarly journals Application of sonication and freezing as initial treatments before microwave-vacuum drying of cranberries

2019 ◽  
Vol 2 (22) ◽  
pp. 151-167 ◽  
Author(s):  
Izabela Staniszewska ◽  
Szymon Staszyński ◽  
Magdalena Zielińska
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Physical Properties ◽  
Color Change ◽  
Vacuum Drying ◽  
Drying Time ◽  
Dried Fruits ◽  
Microwave Vacuum Drying ◽  
Drying Kinetic

The aim of study was to determine the influence of sonication and freezing on the kinetic of the microwave-vacuum drying, energy consumption and physical properties of whole cranberries as well as evaluate the applicability of sonication instead of freezing in order to change their physical properties and the drying kinetic of whole cranberries. Microwave-vacuum drying of whole cranberries with/without initial treatments took from 12 ± 1 to 14.5 ± 0.5 minutes. All of treatments did not significantly shorten the drying time of cranberries. However, they increased SMER values even by 31%. Despite of cryogenic freezing, all of treatments significantly increased the values of Dew. Sonication combined with drying allowed to obtain dried berries characterized by the lowest cohesiveness (0.19±0.02), springiness (0.62±0.02) and chewiness (3.4±0.8 N), while cryogenic freezing combined with drying allowed to obtain dried fruits characterized by highest springiness (0.75±0.03) and low chewiness (3.3±0.5 N). The highest lightness (32.2±0.7), redness (32.6±0.8), and yellowness (11.1±0.7) were found for fruits subjected to initial convective freezing before drying. The efficiency of sonication in color change was comparable to cryogenic freezing and much lower than convective freezing. All of initial treatments increased such thermal properties of dried cranberries as thermal conductivity and thermal diffusivity.

Thermal Contact Resistance of Phase Change and Grease Type Polymeric Materials

2000 ◽  
Author(s):  
Ravi S. Prasher ◽  
Craig Simmons ◽  
Gary Solbrekken
Keyword(s):  
Thermal Conductivity ◽  
Contact Resistance ◽  
Phase Change ◽  
High Performance ◽  
Phase Change Materials ◽  
Thermal Contact ◽  
Polymeric Materials ◽  
Thermal Interface Material ◽  
Heat Spreader ◽  
Thermal Grease

Abstract Thermal interface material (TIM) between the die and the heat spreader or between the heat spreader and the heat sink in any electronic package plays a very important role in the thermal management of electronic cooling. Due to increased power and power density high-performance TIMs are sought every day. Phase change materials (PCM) seem to be very good alternative to traditionally used thermal greases because of various reasons. These phase change materials also have the advantage of being reworked easily without damaging the die. Typically these phase change materials are polymer based and are particle laden to enhance their thermal conductivity. The thermal conductivity of these materials is relatively well understood than their contact resistance. Current work focuses on explicitly measuring the contact resistance and the thermal conductivity of a particular phase change TIM and some silicon-based greases. Effect of various parameters, which can affect the contact resistance of theses TIMs and Greases, are also captured. The steady state measurements of the thermal conductivity and the contact resistance was done on an interface tester. In general the work on the contact resistance of fluid-like polymer based TIM, such as thermal grease or phase change polymer has been experimental in the past. A semi-analytical model, which captures the various parameters affecting the contact resistance of two class of materials; the phase change and the thermal grease is also developed in this paper. This model fits very well with the experimental data.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

Thermal Properties of Thin Metallic Layer Deposited on Insulators: Effect of the Interface on the Independent Determination of the Thermal Diffusivity and Conductivity of the Layer

2008 ◽  
Author(s):  
Danie`le Fournier ◽  
Jean Paul Roger ◽  
Christian Fretigny
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Thermal Resistance ◽  
Thermal Contact ◽  
Heat Diffusion ◽  
Metallic Layer ◽  
Good Thermal Contact ◽  
Lateral Heat

Lateral heat diffusion thermoreflectance is a very powerful tool for determining directly the thermal diffusivity of layered structures. To do that, experimental data are fitted with the help of a heat diffusion model in which the ratio between the thermal conductivity k and the thermal diffusivity D of each layer is fixed, and the thermal properties of the substrate are known. We have shown in a previous work that it is possible to determine independently the thermal diffusivity and the thermal conductivity of a metallic layer deposited on an insulator, by taking into consideration all the data obtained at different modulation frequencies. Moreover, it is well known that to prevent a lack of adhesion of a gold film deposited on substrates like silica, an intermediate very thin (Cr or Ti) layer is deposited to assure a good thermal contact. We extend our previous work: the asymptotic behaviour determination of the surface temperature wave at large distances from the modulated point heat source for one layer deposited on the substrate to the two layers model. In this case (very thin adhesion coating whose thermal properties and thickness are known), it can be establish that the thermal diffusivity and the thermal conductivity of the top layer can still be determined independently. It is interesting to underline that the calculus can also be extended to the case of a thermal contact resistance which has often to be taken into account between two solids. We call thermal resistance a very thin layer exhibiting a very low thermal conductivity. In this case, the three parameters we have to determine are the thermal conductivity and the thermal diffusivity of the layer and the thermal resistance. We will show that, in this case, the thermal conductivity of the layer is always obtained independently of a bound of the couple thermal resistance – thermal diffusivity, the thermal diffusivity being under bounded and the thermal resistance lower bounded. Experimental results on thin gold layers deposited on silica with and without adhesion layers are presented to illustrate the method. Discussions on the accuracy will also be presented.

Thermal Properties of Tungsten SRM’S 730 and 799

1978 ◽  
Vol 100 (2) ◽  
pp. 330-333 ◽  
Author(s):  
R. E. Taylor
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Thermal Properties ◽  
High Temperature ◽  
Thermal Diffusivity ◽  
Thermophysical Properties ◽  
Room Temperature ◽  
Standard Material ◽  
International Program ◽  
Sintered Tungsten

Samples of sintered and arc-cast tungsten are available from NBS as thermal conductivity (SRM 730) and electrical resistivity (SRM 799) standards for the temperature range from 4 to 3000K. NBS recommended values for these properties above room temperature are based on results of various researchers during a previous international program which included arc-cast and sintered tungsten. The sintered tungsten used in this program was found to be unsuited for use as a standard material due to inhomogeneity and high temperature instability. The present paper gives results at high temperatures for thermal conductivity, electrical resistivity, specific heat, thermal diffusivity and Wiedemann-Franz-Lorenz ratio for a sample of the NBS sintered tungsten using the Properties Research Laboratory’s multiproperty apparatus. These results are compared to values recommended by the Thermophysical Properties Research Center, NBS, and an international program.

Sign in / Sign up

Export Citation Format

Share Document