scholarly journals Evaluating the optimal sensor placement for smoke detection

2016 ◽  
Vol 26 (1) ◽  
pp. 33-50 ◽  
Author(s):  
Mirjana Maksimovic ◽  
Vladimir Milosevic
Keyword(s):  
Wireless Sensor Networks ◽  
Network Design ◽  
Network Lifetime ◽  
Fire Detection ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Smoke Detection ◽  
Wireless Sensor Nodes ◽  
Minimum Number ◽  
Fire Ignition

Wireless Sensor Networks (WSNs) consist of wireless sensor nodes, where the choice of their deployment scheme depends highly on the type of sensors, their application, and the environment they will operate in. The performance of WSNs can be affected if the network is deployed under different topologies. In this paper various strategies for positioning nodes in WSNs for fire detection (grid, triangular and strip) are discussed. We propose the proper placement of the smoke sensors to satisfy two important network design objectives: to maximize the network lifetime after fire ignition, and to achieve full coverage by using a minimum number of sensors (especially in a deterministic node deployment).

scholarly journals Calculating the Number of Cluster Heads Based on the Rate-Distortion Function in Wireless Sensor Networks

2014 ◽  
Vol 2014 ◽  
pp. 1-7
Author(s):  
Mingxin Yang ◽  
Jingsha He ◽  
Yuqiang Zhang
Keyword(s):  
Wireless Sensor Networks ◽  
Energy Consumption ◽  
Sensor Networks ◽  
Data Fusion ◽  
Rate Distortion ◽  
Distortion Function ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Wireless Sensor Nodes ◽  
Cluster Heads

Due to limited resources in wireless sensor nodes, energy efficiency is considered as one of the primary constraints in the design of the topology of wireless sensor networks (WSNs). Since data that are collected by wireless sensor nodes exhibit the characteristics of temporal association, data fusion has also become a very important means of reducing network traffic as well as eliminating data redundancy as far as data transmission is concerned. Another reason for data fusion is that, in many applications, only some of the data that are collected can meet the requirements of the sink node. In this paper, we propose a method to calculate the number of cluster heads or data aggregators during data fusion based on the rate-distortion function. In our discussion, we will first establish an energy consumption model and then describe a method for calculating the number of cluster heads from the point of view of reducing energy consumption. We will also show through theoretical analysis and experimentation that the network topology design based on the rate-distortion function is indeed more energy-efficient.

scholarly journals Wireless Sensor Networks for Indoor Environment Monitoring Using LabVIEW

2011 ◽  
pp. 87-90
Author(s):  
Mrutyunjay Rout ◽  
Dr. Harish Kumar Verma ◽  
Subhashree Das
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Indoor Environment ◽  
Environmental Parameters ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Environment Monitoring ◽  
Wireless Sensor Nodes ◽  
Local Decision ◽  
Mems Technology

Wireless sensor networks (WSNs) have gained worldwide attention in recent years, particularly with the rapid progress in Micro-Electro-Mechanical Systems (MEMS) technology which has facilitated the development of smart sensors. These sensors are small, with limited processing and computing resources, and they are inexpensive compared to traditional sensors. These sensor nodes can sense, measure, and gather information from the environment and, based on some local decision process, they can transmit the sensed data to the user. WSNs are large networks made of a numerous number of sensor nodes with sensing, computation, and wireless communication capabilities. In present work we provide a brief summary of the state-ofthe- art in wireless sensor networks, investigate the feasibility of indoor environment monitoring using crossbow wireless sensor nodes. Here we used nesC programming language and TinyOS operating system for programming Crossbow sensor nodes and LabVIEW GUI is used for displaying different indoor environmental parameters such as temperature, humidity and light acquired from different Wireless sensor nodes. These sensor readings can help building administrators to monitor the physical conditions of the environment in a building for creating optimized energy usage.

Cost Minimization of Sensor Placement and Routing in Wireless Sensor Networks

2020 ◽  
pp. 1286-1301
Author(s):  
Tata Jagannadha Swamy ◽  
Garimella Rama Murthy
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Cost Minimization ◽  
Real Life ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Wireless Sensor Nodes ◽  
Technological Advances ◽  
Strongly Connected ◽  
Placement And Routing

Wireless Sensor Nodes (WSNs) are small in size and have limited energy resources. Recent technological advances have facilitated widespread use of wireless sensor networks in many real world applications. In real life situations WSN has to cover an area or monitor a number of nodes on a plane. Sensor node's coverage range is proportional to their cost, as high cost sensor nodes have higher coverage ranges. The main goal of this paper is to minimize the node placement cost with the help of uniform and non-uniform 2D grid planes. Authors propose a new algorithm for data transformation between strongly connected sensor nodes, based on graph theory.

Event Based Data Gathering in Wireless Sensor Networks

2012 ◽  
pp. 445-462 ◽  
Author(s):  
Asfandyar Khan ◽  
Azween Abdullah ◽  
Nurul Hasan
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Network Lifetime ◽  
Energy Savings ◽  
Detection System ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Detection Model ◽  
Physical Environments ◽  
Event Based

Wireless sensor networks (WSANs) are increasingly being used and deployed to monitor the surrounding physical environments and detect events of interest. In wireless sensor networks, energy is one of the primary issues and requires the conservation of energy of the sensor nodes, so that network lifetime can be maximized. It is not recommended as a way to transmit or store all data of the sensor nodes for analysis to the end user. The purpose of this “Event Based Detection” Model is to simulate the results in terms of energy savings during field activities like a fire detection system in a remote area or habitat monitoring, and it is also used in security concerned issues. The model is designed to detect events (when occurring) of significant changes and save the data for further processing and transmission. In this way, the amount of transmitted data is reduced, and the network lifetime is increased. The main goal of this model is to meet the needs of critical condition monitoring applications and increase the network lifetime by saving more energy. This is useful where the size of the network increases. Matlab software is used for simulation.

scholarly journals Energy Efficient Trust Node Based Routing Protocol (EETRP) to Maximize the Lifetime of Wireless Sensor Networks in Plateaus

2019 ◽  
Vol 15 (06) ◽  
pp. 113 ◽  
Author(s):  
Nandoori Srikanth ◽  
Muktyala Sivaganga Prasad
Keyword(s):  
Energy Efficiency ◽  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Network Lifetime ◽  
Routing Protocol ◽  
Energy Efficient ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Mobile Nodes ◽  
Energy Limitation

<p>Wireless Sensor Networks (WSNs) can extant the individual profits and suppleness with regard to low-power and economical quick deployment for numerous applications. WSNs are widely utilized in medical health care, environmental monitoring, emergencies and remote control areas. Introducing of mobile nodes in clusters is a traditional approach, to assemble the data from sensor nodes and forward to the Base station. Energy efficiency and lifetime improvements are key research areas from past few decades. In this research, to solve the energy limitation to upsurge the network lifetime, Energy efficient trust node based routing protocol is proposed. An experimental validation of framework is focused on Packet Delivery Ratio, network lifetime, throughput, energy consumption and network loss among all other challenges. This protocol assigns some high energy nodes as trusted nodes, and it decides the mobility of data collector.  The energy of mobile nodes, and sensor nodes can save up to a great extent by collecting data from trusted nodes based on their trustworthiness and energy efficiency.  The simulation outcome of our evaluation shows an improvement in all these parameters than existing clustering and Routing algorithms.<strong></strong></p>

Salp

2020 ◽  
pp. 41-56 ◽  
Author(s):  
Vrajesh Kumar Chawra ◽  
Govind P. Gupta
Keyword(s):  
Wireless Sensor Networks ◽  
Network Lifetime ◽  
Cluster Head ◽  
Residual Energy ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Cluster Head Selection ◽  
Research Issue ◽  
Energy Hole ◽  
Node Clustering

The formation of the unequal clusters of the sensor nodes is a burning research issue in wireless sensor networks (WSN). Energy-hole and non-uniform load assignment are two major issues in most of the existing node clustering schemes. This affects the network lifetime of WSN. Salp optimization-based algorithm is used to solve these problems. The proposed algorithm is used for cluster head selection. The performance of the proposed scheme is compared with the two-node clustering scheme in the term of residual energy, energy consumption, and network lifetime. The results show the proposed scheme outperforms the existing protocols in term of network lifetime under different network configurations.

scholarly journals Energy-Efficient Unequal Chain Length Clustering for Wireless Sensor Networks in Smart Cities

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Mohammad Baniata ◽  
Jiman Hong
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Chain Length ◽  
Network Lifetime ◽  
Routing Protocol ◽  
Energy Efficient ◽  
Smart Cities ◽  
Cluster Head ◽  
Sensor Nodes ◽  
Wireless Sensor

The recent advances in sensing and communication technologies such as wireless sensor networks (WSN) have enabled low-priced distributed monitoring systems that are the foundation of smart cities. These advances are also helping to monitor smart cities and making our living environments workable. However, sensor nodes are constrained in energy supply if they have no constant power supply. Moreover, communication links can be easily failed because of unequal node energy depletion. The energy constraints and link failures affect the performance and quality of the sensor network. Therefore, designing a routing protocol that minimizes energy consumption and maximizes the network lifetime should be considered in the design of the routing protocol for WSN. In this paper, we propose an Energy-Efficient Unequal Chain Length Clustering (EEUCLC) protocol which has a suboptimal multihop routing algorithm to reduce the burden on the cluster head and a probability-based cluster head selection algorithm to prolong the network lifetime. Simulation results show that the EEUCLC mechanism enhanced the energy balance and prolonged the network lifetime compared to other related protocols.

An Energy Aware Routing Based on Swarm Intelligence for Wireless Sensor Networks

2013 ◽  
Vol 706-708 ◽  
pp. 635-638
Author(s):  
Yong Lv
Keyword(s):  
Wireless Sensor Networks ◽  
Energy Consumption ◽  
Sensor Networks ◽  
Swarm Intelligence ◽  
Network Lifetime ◽  
Average Energy ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Energy Aware ◽  
Energy Efficient Routing

Wireless Sensor Networks consisting of nodes with limited power are deployed to collect and distribute useful information from the field to the other sensor nodes. Energy consumption is a key issue in the sensor’s communications since many use battery power, which is limited. In this paper, we describe a novel energy efficient routing approach which combines swarm intelligence, especially the ant colony based meta-heuristic, with a novel variation of reinforcement learning for sensor networks (ARNet). The main goal of our study was to maintain network lifetime at a maximum, while discovering the shortest paths from the source nodes to the sink node using an improved swarm intelligence. ARNet balances the energy consumption of nodes in the network and extends the network lifetime. Simulation results show that compared with the traditional EEABR algorithm can obviously improve adaptability and reduce the average energy consumption effectively.

scholarly journals An Energy-Aware Method for Selecting Cluster Heads in Wireless Sensor Networks

2020 ◽  
Vol 10 (21) ◽  
pp. 7886
Author(s):  
Atefeh Rahiminasab ◽  
Peyman Tirandazi ◽  
M. J. Ebadi ◽  
Ali Ahmadian ◽  
Mehdi Salimi
Keyword(s):  
Wireless Sensor Networks ◽  
Sensor Networks ◽  
Network Lifetime ◽  
Cluster Head ◽  
Base Station ◽  
Energy Resources ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Dynamic Clustering ◽  
Clustering Protocol

Wireless sensor networks (WSNs) include several sensor nodes that have limited capabilities. The most critical restriction in WSNs is energy resources. Moreover, since each sensor node’s energy resources cannot be recharged or replaced, it is inevitable to propose various methods for managing the energy resources. Furthermore, this procedure increases the network lifetime. In wireless sensor networks, the cluster head has a significant impact on system global scalability, energy efficiency, and lifetime. Furthermore, the cluster head is most important in combining, aggregating, and transferring data that are received from other cluster nodes. One of the substantial challenges in a cluster-based network is to choose a suitable cluster head. In this paper, to select an appropriate cluster head, we first model this problem by using multi-factor decision-making according to the four factors, including energy, mobility, distance to centre, and the length of data queues. Then, we use the Cluster Splitting Process (CSP) algorithm and the Analytical Hierarchy Process (AHP) method in order to provide a new method to solve this problem. These four factors are examined in our proposed approach, and our method is compared with the Base station Controlled Dynamic Clustering Protocol (BCDCP) algorithm. The simulation results show the proposed method in improving the network lifetime has better performance than the base station controlled dynamic clustering protocol algorithm. In our proposed method, the energy reduction is almost 5% more than the BCDCP method, and the packet loss rate in our proposed method is almost 25% lower than in the BCDCP method.

Novel Steam Powered Gravity Assisted Standalone Power System (SP-GA-SP System) Design for Remote Wireless Sensor Networks

2013 ◽  
Vol 440 ◽  
pp. 248-253
Author(s):  
P. Shunmuga Perumal ◽  
V. Rhymend Uthariaraj ◽  
V.R. Elgin Christo
Keyword(s):  
Wireless Sensor Networks ◽  
Power Supply ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Wireless Sensor Nodes ◽  
Electrical Grid ◽  
Remote Areas ◽  
Dense Forest ◽  
Battery Systems ◽  
Remote Sites

Uninterrupted power supply through electrical grid is not possible for many remote areas like dense forest, hill areas, and deserts. The objective of the proposed work is to generate stand alone electricity using steam powered gravity assisted SP system for remote WSN applications. The proposed design drives the generator by triggering gravity force using steam powered cylinders with high thermal efficiency. The proposed SP system is used to recharge the battery systems of UAVs in remote sites thereby the UAVs are further used to recharge the remote wireless sensor nodes using laser beam transmissions.

Sign in / Sign up

Export Citation Format

Share Document