scholarly journals Sifat Fisis dan Mekanis Papan Semen dari Serat Tandan Kosong Kelapa Sawit (The Physical and Mechanical Properties of Cement Board Made from Oil Palm Empty Fruit Bunches Fibers)

2016 ◽  
Vol 8 (2) ◽  
pp. 43-52 ◽  
Author(s):  
Djoko Purwanto
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Oil Palm ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Empty Fruit Bunches ◽  
Screw Withdrawal ◽  
Cement Board

Oil palm empty fruit bunches (OPEFB) fiber were industrial waste that has not been widely used by the community, only stacked and cause odors that interfere with the surrounding environment. This research studied the utilization of OPEFB fiber for cement board products using cement as resin and CaCl2 as accelerator. Laboratory scale cement board made from OPEFB fiber were mixed with cement, and CaCl2. The composition of fiber and cement were 1:1, 1:1.5, 1:2, and CaCl2 variations were 0%, 1% and 3%. A mixture of fibers, cement and CaCl2 was compressed at the pressure of 4 ton for 24 hours. The cement boards were tested for physical and mechanical properties according to JIS A 5417-1992, and the results were compared to the requirements of the cement board JIS A 5417-1992. Cement board made from fiber and cement composition 1:1.5 and CaCl2 content 3% produced moisture content, thickness swelling, water absorption, density, modulus of rupture/MOR, modulus of elasticity/MOE and screw withdrawal strength that met the requirement of JIS A 5417-1992. The composition of fiber and cement and the variations of CaCl2 content produced significant effect on water content, water absorption, thickness swelling, modulus of rupture/MOR, modulus of elasticity/MOE and screw withdrawal strength on cement boards.Keywords : oil palm empty fruit bunches fiber, cement boards, physical and mechanical properties

SIFAT FISIK MEKANIK PAPAN PARTIKEL TANPA PEREKAT DARI TANDAN KOSONG KELAPA SAWIT (Elaeis Guineensis acq)

2014 ◽  
Vol 6 (1) ◽  
pp. 15 ◽  
Author(s):  
Budi Tri Cahyana
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Content ◽  
Oil Palm ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Particle Board ◽  
Thickness Swelling ◽  
Empty Fruit Bunches

This research aimed to get the physical and mechanical properties of non adhesive-particle board from oil palm empty fruit bunches. The oil palm empty fruit bunches were degradated to fibre and boiled in boiling water during 60 minute then dried in ± 2 weeks. The dried raw material was chopped to be fibre in 5 mesh, 10 mesh, and 16 mesh. It were complied into a mold and then hot pressed in 35 kgf/cm2 pressure during 10 minute with 3 of temperature variety, 160°C, 180°C and 200°C. The result showed that the average of particle board water content was 7,11 -  9,85 % and the density was 0,63 – 0,76 gr/cm3. The highest thickness swelling was 22,59 % in 10 mesh and 160 0C (a2b1) temperature of oil palm empty fruit bunches. The modulus of rupture was 211,67 kg/cm2  in 10 mesh and 180 0C (a2b2) temperature. The modulus of elasticity was 490,85 kg/cm2 in 10 mesh and 160 0C (a2b1) temperature. The tensile strength was 7,49 kg/cm2 in 5 mesh and 200 0C (a1b3) temperature. The average of physical and mechanical properties such as water content, density, modulus of rupture, tensile strength were fulfill the SNI requirement, while the average of thickness swelling and modulus of elasticity were not fulfill the SNI requirement.Keywords: oil palm empty fruit bunches, particle board

scholarly journals INFLUENCE OF THERMAL MODIFICATION ON THE PHYSICAL AND MECHANICAL PROPERTIES OF Eucalyptus badjensis MIXED PARTICLEBOARD / OSB PANELS

FLORESTA ◽  
2021 ◽  
Vol 51 (2) ◽  
pp. 419
Author(s):  
Giuliano Ferreira Pereira ◽  
Setsuo Iwakiri ◽  
Rosilani Trianoski ◽  
Polliana D'angelo Rios ◽  
Renan Zunta Raia
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Phenol Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Dry Mass ◽  
Thermal Modification ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Swelling Properties ◽  
Different Temperatures

The objective of this research was to evaluate the effects of thermal modifications, at different temperatures and exposure times, on the technological properties of mixed particleboard / OSB panels made out of Eucalyptus badjensis. Using the wood of Eucalyptus badjensis, Particleboard, OSB and mixed Particleboard/OSB panels (control and thermally modified) were manufactured. The mixed panels’ thermal modification was carried out under three temperatures (180ºC, 200ºC and 220ºC) and two exposure times (10 minutes and 12 minutes). For the panels’ manufacturing, 6% of phenol-formaldehyde adhesive and 1% of paraffin were employed, which was calculated based on the particles’ dry mass. The water absorption and thickness swelling properties were evaluated after 2 and 24 hours of immersion, in addition to the panels’ modulus of elasticity, modulus of rupture and internal bond. Based on the results, we were able to conclude that the thermal modification affected most of the physical properties positively. From the different exposure times studied, the most effective one was the period of 12 minutes, especially for water absorption after 2 hours, which caused a reduction of 11.27%. In turn, the most effective temperature was of 220ºC, highlighting the thickness swelling after 24 hours, which caused a swelling decrease of 23.76% in comparison with the control panels. Regarding the mechanical properties, the thermal modification, in terms of the studied exposure times and temperatures, did not affect the results of the mixed particleboard /OSB panels. 

scholarly journals Effects of thermo-hydro-mechanical treatments on various physical and mechanical properties of poplar (Populus) wood

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 9596-9610
Author(s):  
Yali Shao ◽  
Lili Li ◽  
Zhangjing Chen ◽  
Sunguo Wang ◽  
Ximing Wang
Keyword(s):  
Mechanical Properties ◽  
Thermal Treatment ◽  
Modulus Of Elasticity ◽  
Mechanical Treatment ◽  
Elasticity Modulus ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Compression Rate ◽  
Thickness Swelling ◽  
Maximum Thickness

Poplar (Populus) wood was subjected in this work to thermo-hydro-mechanical treatment. The influence of the treatment parameters on the physical and mechanical properties were investigated. The wood samples were densified under three compression ratios (0%, 30%, and 50%), and thermally treated at three temperatures (180 °C, 200 °C, and 220 °C), at three thermal treatment durations (3 h, 4 h, and 5 h). The density, modulus of elasticity, modulus of rupture, radial hardness, and thickness swelling were measured. The results showed that the densities of the samples increased by 36.6% to 49.7%. As the compression rate increased, the temperature, duration, modulus of elasticity, modulus of rupture, and hardness increased. However, the dimensions of the densified samples were less stable. Compared to the densified samples, the maximum thickness swelling could be reduced by 74% (from 29.7% to 7.8%) when subjected to a thermal treatment at 220 °C for 3 h.

scholarly journals Physical and Mechanical Properties Evaluation of Corncob and Sawdust Cement Bonded Ceiling Boards

2019 ◽  
Vol 42 ◽  
pp. 65-75 ◽  
Author(s):  
Atoyebi Olumoyewa Dotun ◽  
Odeyemi Samson Olalekan ◽  
Azeez Lateef Olugbenga ◽  
Modupe Abayomi Emmanuel
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Cement Content ◽  
Physical And Mechanical Properties ◽  
American National Standard Institute ◽  
Mechanical Tests ◽  
Industrial Wastes ◽  
Modulus Of Rupture ◽  
National Standard ◽  
Thickness Swelling

This study considered the production of composite ceiling boards from both agricultural and industrial wastes. Boards with different blending proportions by weight of cement, corncob and sawdust (Cem:Ccb:Swd) were produced and tested. Physical and mechanical tests such as Water Absorption (WA), Thickness Swelling (TS), Modulus of Elasticity (MOE) and Modulus of Rupture (MOR) were carried out on the products. The findings revealed that the board with Cem:Ccb:Swd blending proportion 50:10:40 gave the highest values of MOE and MOR and also had the lowest values of WA and TS. The MOE and MOR values of 3.432 are both higher than the minimum values of 550 N/mm2 and 3 N/mm2 specified for MOE and MOR respectively by the American National Standard Institute, for general-use particle boards. The cement content is inversely proportional to the physical properties and directly proportional to the mechanical properties.

scholarly journals PENGARUH PERENDAMAN PARTIKEL TERHADAP SIFAT FISIS DAN MEKANIS PAPAN PARTIKEL DARI AMPAS TEBU (Saccharum officinarum)

PERENNIAL ◽  
2008 ◽  
Vol 4 (1) ◽  
pp. 6
Author(s):  
Apri Heri Iswanto ◽  
Zahrial Coto ◽  
Kurniawansyah Effendy
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Modulus Of Elasticity ◽  
Internal Bond ◽  
Physical And Mechanical Properties ◽  
Saccharum Officinarum ◽  
Hot Water ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Holding Power

The objective of this research is to research the effect of particle soaking to physical and mechanical properties particleboard that resulted. The best result of particleboard is particleboard with treatment of hot water soaking. From this result obtained average of physical properties of particleboard (i.e. density, moisture content, water absorption, and thickness swelling) are 0.7 g/cm3; 9.58%; 52.27%; 10.05%. While the result average of mechanical properties of particleboard (i.e. Modulus of Rupture, Modulus of Elasticity, Internal Bond and Screw Holding Power) are 118.79 kg/cm2; 8.909 kg/cm2; 1.85 kg/cm2; 28.40 kg. Key words: Soaking, bagasse, particleboard, physical and mechanical properties References

Effect of Ozone Treatment on Properties of Screw Pressed and Non-Screw Pressed Empty Fruit Bunch Medium Density Particleboard

2015 ◽  
Vol 1134 ◽  
pp. 116-122
Author(s):  
Roslan Ali ◽  
Mohamad Nurul Azman Mohammad Taib ◽  
Kamal Wok ◽  
Shawaluddin Tahiruddin ◽  
Mohd Amrin Abdullah
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Modulus Of Rupture ◽  
Ozone Treatment ◽  
Medium Density ◽  
Internal Bonding ◽  
Empty Fruit Bunch ◽  
Thickness Swelling

This study was done to investigate the effects of ozone treatment as a method to improve the properties of empty fruit bunch (EFB) medium density particleboard. Two types of EFB were used in this study i.e. screw pressed and non-screw pressed empty fruit bunch. These EFB were treated in an ozone chamber for 8 hours prior to particleboard manufacturing. The mechanical properties, Modulus of Elasticity (MOE), Modulus of Rupture (MOR) and Internal Bonding (IB) and physical properties, water Absorption (WA) and Thickness Swelling (TS) of EFB particleboard were determined. The results showed that the ozone treatment could increase the MOR and IB values of EFB particleboard, but had no significant effect on MOE values. For physical properties, the values showed no improvement for TS and WA. The panels manufactured using ozone treatment was found suitable for applications for furniture products.

scholarly journals The classical mechanics engineered of Bambusa vulgaris and Schizostachyum brachycladum

2021 ◽  
Vol 6 (2) ◽  
pp. 57-61
Author(s):  
Mohamad Saiful Sulaiman ◽  
Sitti Fatimah Mhd. Ramle ◽  
Rokiah Hashim ◽  
Othman Sulaiman ◽  
Mohd Hazim Mohamad Amini ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Water Absorption ◽  
Classical Mechanics ◽  
Basic Density ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Flexural Test ◽  
Thickness Swelling ◽  
Bambusa Vulgaris

Physical and mechanical properties of Bambusa vulgaris and Schizostachyum brachycladum wereinvestigated. The sample were classified into two different ages which are young and mature foreach culm of bamboo. The aim of this study to investigate the physical properties such as density,basic density, moisture content, water absorption and thickness swelling. Other than that, themechanical properties also help to determine their flexural test for modulus of rupture (MOR) andmodulus of elasticity (MOE). The method used to analyse physical and mechanical properties werefollowing the ISO standard. From this study, young Bambusa vulgaris has indicated the highercontent of moisture content, water absorption and thickness swelling with 67.66%, 2.69% and34.03%, respectively while mature Schizostachyum brachycladum has shown the higher value inbasic density, density, and flexural test for MOR and MOE with 876.33 kg/m3, 1084.49 kg/m3, 317.01 N/mm2 and 122986.18 N/mm2, respectively.

Effect of Density on Physical and Mechanical Properties of Reconstituted Small-Sized Bamboo Fibrous Sheet Composite

2010 ◽  
Vol 150-151 ◽  
pp. 634-639 ◽  
Author(s):  
Rong Xian Zhu ◽  
Wen Ji Yu
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Cold Pressing ◽  
Shearing Strength

The effect of density on physical and mechanical properties of phenolic-impregnated cold-pressing reconstituted small-sized bamboo fibrous sheet composite was evaluated. The results indicated that with the density increased from 0.85g/cm3 to 1.20 g/cm3: water absorption decreased, thickness swelling increased first and then decreased; the value of modulus of rupture(MOR) increased from 120MPa to 230MPa, R2 was 0.885; the value of modulus elasticity(MOE) increased from 1.8×104MPa to 2.8×104MPa, R2 was 0.978; the shearing strength (perpendicular loading) increased from 6.5MPa to 18MPa, R2 was 0.978;the shearing strength( parallel loading) increased from 6.3MPa to 26MPa, R2 was 0.973;the compression parallel to grain values increased from 80MPa to 120MPa.

scholarly journals SIFAT FISIKA DAN MEKANIKA PAPAN SEMEN DARI SERAT KULIT BATANG SAGU (Metroxylon Sp)

2019 ◽  
Vol 7 (3) ◽  
Author(s):  
Peterson Peterson ◽  
M Dirhamsyah ◽  
Nurhaida Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Water Absorption ◽  
Fiber Length ◽  
Physical Property ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Average Value ◽  
Wood Processing ◽  
Cement Board

The research aims to examine the physical and mechanical properties of cement board from sago fiber waste (Metroxylon Sp) based on cement size and composition and determine the best ratio of cement and sago fiber (Metroxylon sp) and meet the standards of JIS A 5417: 1992. The study was conducted at the Laboratorium WoodWorkshop, Wood Processing, Wood Technology and PT. Duta Pertiwi Nusantara Pontianak. The method used was an experimental method in a factorial Randomized Complete Design factorial experiment of 2 x 3 with 3 replications and a total of 18 experiments. The factors used in sago fiber length (Factor A) and fiber (Factor B).  The tests include physical properties and mechanical properties with a target density of 1 gr / cm³. The results showed that the average value of the physical properties of the cement board included density 0.9713 gr / cm³ - 1.2246 gr / cm³, moisture content 3.5054% - 3.9448%, water absorption 0.9746 % - 1.1318% and thick Development 0.8649% - 0.9892%. The mean mechanical properties of cement board include MOE 10,564,6646 kg / cm² - 35,475,7865 kg / cm² and MOR 7,5797 kg / cm² - 25,8554 kg / cm². The best research is in treatment (a1b2) with a ratio of cement and fiber (80:20) with a length of sago fiber 2 cm and meets the standards of JIS A 5417: 1992 with the of 23, with a physical property density value of 1.2198 gr / cm³, water content is 3.7401%, water absorption is 0.9944%, and thickness development is 0.9048%. The mechanical properties value of Modulus of Elasticity is 28439.1825 kg / cm² and Modulus of Rupture is 25.8554 kg / cm².Keyword:   Cement Comparison,  Fiber Length, Sago Fiber, Physical and Mechanical Propertie

scholarly journals The effect of oil palm trunk particles and composite density on the physical and mechanical properties of rigid polyurethane foam composite

2021 ◽  
Vol 891 (1) ◽  
pp. 012003
Author(s):  
S S Munawar ◽  
C D Widyanto ◽  
L S Hutahean ◽  
D Purnomo ◽  
B Subiyanto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polyurethane Foam ◽  
Oil Palm ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Rigid Polyurethane Foam ◽  
Oil Palm Trunk ◽  
Foam Composite ◽  
Screw Withdrawal ◽  
Closed Mold

Abstract The oil palm trunk (OPT) particle was used as a filler for the manufacture of rigid polyurethane foam composites (RPUFC). The purpose of this research is to investigate the effect of OPT particle content and variation of composite density on the physical and mechanical properties of RPUFC. The RPUFC was created with five different volume fractions of OPT particles (0, 2.5, 5, 7.5, 10 wt%) and three different composite densities (40, 50, 60 kg/m3). The OPT particles, polyols, and isocyanate were mixed, poured and formed in a closed mold. The moisture content (MC), water absorption (WA), compressive strength (CS), screw withdrawal (SW), and internal bonding strength (IB) properties were determined according to JIS A 5908-2003. The flexural strength (FS) properties were determined according to ASTM D790. The physical properties (MC, WA) were increased with increasing OPT particles in the RPUFC. The RPUFC with 2.5% OPT particle was higher in modulus of rupture, modulus of young and CS values compared to RPUFC control. The IB and SW values were increased when 2.5% OPT particles were added to RPUFC. The best PURFCs were produced with the addition of 2.5% particles at a density of 50 and 60 kg/m3.

Sign in / Sign up

Export Citation Format

Share Document