Effect of Zn Content on Structure, Roughness and Corrosion Behavior of Zn-Ni Alloys

2019 ◽  
Vol 17 (17) ◽  
pp. 17-22
Author(s):  
Hayette Faid
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Stripping Voltammetry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Alloys ◽  
Sulfate Bath ◽  
Zn Content ◽  
Polarization Test ◽  
Δ Phase

AbstractIn this work, Zn-Ni alloys have been deposited on steel from sulfate bath, by electrodeposition method. The effect of Zn content on deposits properties was studied by cyclic voltammetry (CV), chronoaperometry (CA), linear stripping voltammetry (ALSV) and diffraction (XRD) and scanning electronic microscopy (SEM). The corrosion behavior in 3.5 wt. NaCl solution was examined using anodic polarization test and electrochemical impedance spectroscopy. X-ray diffraction of show that Zn-Ni alloys structure is composed of δ phase and γ phase, which increase with the decrease of Zn content in deposits. Results show that deposits obtained from bath less Zn2+ concentration exhibited better corrosion resistance.

scholarly journals Effect of Graphene Oxide Concentration in Electrolyte on Corrosion Behavior of Electrodeposited Zn–Electrochemical Reduction Graphene Composite Coatings

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 758 ◽  
Author(s):  
Yang ◽  
Zhang ◽  
Wang ◽  
Wang ◽  
Chen ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Laser Raman Spectroscopy ◽  
304 Stainless Steel ◽  
Sulfate Electrolyte ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tafel Polarization ◽  
Laser Raman

Pure Zn and Zn–ERGO composite coatings were prepared by direct current electrodeposition on 304 stainless steel. Samples were characterized by X-ray diffraction (XRD), scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM/EDS), and laser Raman spectroscopy (Raman). Results obtained have shown that the concentration of GO sheets in zinc sulfate electrolyte has an important effect on the preferred crystal orientation and the surface morphology of Zn–ERGO composite coatings. A study of the corrosion behavior of the coatings by Tafel polarization and electrochemical impedance spectroscopic (EIS) methods leads to the conclusion that the Zn-1.0 g/L ERGO composite coating possesses the best corrosion resistance compared to the pure Zn coating and other composite coatings in this study.

scholarly journals Effect of Rare Earth Oxides on Microstructure and Corrosion Behavior of Laser-Cladding Coating on 316L Stainless Steel

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 636 ◽  
Author(s):  
Xu ◽  
Wang ◽  
Chen ◽  
Qiao ◽  
Zhang ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Rare Earth ◽  
Corrosion Behavior ◽  
Laser Cladding ◽  
316L Stainless Steel ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Rare Earth Oxides ◽  
X Ray Diffraction ◽  
X Ray

The effect of rare earth oxides on the microstructure and corrosion behavior of laser-cladding coating on 316L stainless steel was investigated using hardness measurements, a polarization curve, electrochemical impedance spectroscopy (EIS), a salt spray test, X-ray diffraction, optical microscopy, and scanning electron microscopy (SEM). The results showed that the modification of rare earth oxides on the laser-cladding layer caused minor changes to its composition but refined the grains, leading to an increase in hardness. Electrochemical and salt spray studies indicated that the corrosion resistance of the 316L stainless steel could be improved by laser cladding, especially when rare earth oxides (i.e., CeO2 and La2O3) were added as a modifier.

The Effect of Zn Concentration on the Corrosion Behavior of the Composite Magnesium-10wt.% Bio-Glass

2015 ◽  
Vol 819 ◽  
pp. 314-318
Author(s):  
Siti Aishah Buyong ◽  
Shamsul Baharin Jamaludin ◽  
Rohaya Abdul Malik
Keyword(s):  
Hydrogen Evolution ◽  
Corrosion Behavior ◽  
Xrd Analysis ◽  
Immersion Test ◽  
Optical Microscope ◽  
Argon Atmosphere ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zn Concentration ◽  
Zn Content

This paper presents the corrosion behavior of the composite Mg-10wt.% bio-glass (45S5) with different concentration of Zn. Bio-glass (BG) was added to the composite in order to improve bioactivity behavior of magnesium. The composite was fabricated by mixing, compacting followed by sintering. Composites was compacted at 550 MPa and sintered at 450°C under an argon atmosphere. Corrosion behavior was investigated by the immersion test. Sintered samples were immersed in 0.9 % NaCI solution and monitored by hydrogen evolution and XRD analysis. The results showed that hydrogen evolution rate decreased with addition of Zn content. The microstructure and phase analysis were observed by optical microscope, scanning electron microscope and x-ray diffraction.

Study on Microstructure and Corrosion Behavior of Ag-Cu-Zn-Ni Alloys

2011 ◽  
Vol 311-313 ◽  
pp. 2132-2137 ◽  
Author(s):  
Fu Xiang Huang ◽  
Ping Yin ◽  
Yong Hong Xu ◽  
Ying Zhang
Keyword(s):  
Corrosion Behavior ◽  
Energy Dispersive Spectrum ◽  
Second Phase ◽  
X Ray Diffraction ◽  
Silver Alloys ◽  
X Ray ◽  
Electrochemical Tests ◽  
Ni Alloys ◽  
Second Phases ◽  
Electronic Microscope

Potentiodynamic electrochemical tests and surface analysis technics, such as scanning electronic microscope (SEM), energy dispersive spectrum (EDS) and X-ray diffraction analysis (XRD), were applied to investigate the microstructure and corrosion behavior of Ag-Cu-Zn-Ni alloys in Na2S solution. The results reveal that the α-Ag phase is the main matrix of the studied silver alloys. The second phase of Ag-4Cu-0.3Ni and Ag-3Cu-Zn-0.3Ni/Ag-6Cu-Zn-0.3Ni are respectively CuNi and CuNi(Zn) phases. The second phases of Ag-6Cu-Zn-0.3Ni are well-distributed, which leads to an improvement in the corrosion resistance in Na2S solution.

scholarly journals Manufacturing of Ti-6%Al and Ti-6%Al-4%V Alloys and Their Corrosion in Sodium Chloride Solutions

Crystals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 181 ◽  
Author(s):  
Hany S. Abdo ◽  
El-Sayed M. Sherif ◽  
Hamed A. El-Serehy
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Al Alloy ◽  
Spectroscopic Techniques ◽  
Uniform Corrosion ◽  
X Ray Diffraction ◽  
Current Time ◽  
X Ray ◽  
Sodium Chloride Solutions

The current research aims at the manufacturing of Ti-6%Al alloy and Ti-6%Al-4%V alloy using the mechanical alloying method and studying their corrosion behavior after various periods of immersions in 3.5% NaCl solutions. The fabricated alloys were also evaluated using spectroscopic techniques such as X-ray diffraction, scanning electron microscopy, and energy dispersive X-ray spectroscopy analyses. The corrosion behavior was studied using potentiodynamic polarization, electrochemical impedance spectroscopy, and chronoamperometric current-time electrochemical methods. It is confirmed that the presence of 4% V greatly decreases the uniform corrosion of the Ti-6%Al alloy as a result of the role of V in decreasing the cathodic, anodic, and corrosion current, and the rate of corrosion along with increasing the corrosion resistance. Increasing the time of immersion to 24 h and further to 48 h highly decreased the corrosion of the alloys. The presence of 4% V and extending the time of exposure thus increase the resistance against corrosion via decreasing the corrosion of Ti-6%Al alloy in the chloride test solution.

Observation of pseudo 10-fold symmetry in the ordered iron-zinc delta phase

1992 ◽  
Vol 50 (1) ◽  
pp. 36-37
Author(s):  
L. A. Giannuzzi ◽  
A. S. Ramani ◽  
P. R. Howell ◽  
H. W. Pickering ◽  
W. R. Bitler
Keyword(s):  
Single Phase ◽  
X Ray Diffraction ◽  
Rich Region ◽  
Average Cell ◽  
X Ray ◽  
Delta Phase ◽  
Cell Dimensions ◽  
Δ Phase ◽  
Morphological Differences ◽  
Concentration Discontinuity

The δ phase is a Zn-rich intermetallic, having a composition range of ∼ 86.5 - 92.0 atomic percent Zn, and is stable up to 665°C. The stoichiometry of the δ phase has been reported as FeZn7 and FeZn10 The deviation in stoichiometry can be attributed to variations in alloy composition used by each investigator. The structure of the δ phase, as determined by powder x-ray diffraction, is hexagonal (P63mc or P63/mmc) with cell dimensions a = 1.28 nm, c = 5.76 nm, and 555±8 atoms per unit cell. Later work suggested that the layer produced by hot-dip galvanizing should be considered as two distinct phases which are characterized by their morphological differences, namely: the iron-rich region with a compact appearance (δk) and the zinc-rich region with a columnar or palisade microstructure (δp). The sub-division of the δ phase was also based on differences in diffusion behavior, and a concentration discontinuity across the δp/δk boundary. However, work utilizing Weisenberg photographs on δ single crystals reported that the variation in lattice parameters with composition was small and hence, structurally, the δk phase and the δp phase were the same and should be thought of as a single phase, δ. Bastin et al. determined the average cell dimensions to be a = 1.28 nm and c = 5.71 nm, and suggested that perhaps some kind of ordering process, which would not be observed by x-ray diffraction, may be responsible for the morphological differences within the δ phase.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

scholarly journals Effect of Molybdenum Content on the Corrosion and Microstructure of Low-Ni, Co-Free Maraging Steels

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 852
Author(s):  
Asiful H. Seikh ◽  
Hossam Halfa ◽  
Mahmoud S. Soliman
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Microstructural Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Alloying Element ◽  
X Ray ◽  
Maraging Steels ◽  
Eds Analysis ◽  
Electroslag Refining

Molybdenum (Mo) is an important alloying element in maraging steels. In this study, we altered the Mo concentration during the production of four cobalt-free maraging steels using an electroslag refining process. The microstructure of the four forged maraging steels was evaluated to examine phase contents by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. Additionally, we assessed the corrosion resistance of the newly developed alloys in 3.5% NaCl solution and 1 M H2SO4 solution through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Furthermore, we performed SEM and energy-dispersive spectroscopy (EDS) analysis after corrosion to assess changes in microstructure and Raman spectroscopy to identify the presence of phases on the electrode surface. The microstructural analysis shows that the formation of retained austenite increases with increasing Mo concentrations. It is found from corrosion study that increasing Mo concentration up to 4.6% increased the corrosion resistance of the steel. However, further increase in Mo concentration reduces the corrosion resistance.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Structure and Electrochemical Behavior of Plasma-Sprayed LSGM Electrolyte Films

2002 ◽  
Vol 756 ◽  
Author(s):  
H. Zhang ◽  
X. Ma ◽  
J. Dai ◽  
S. Hui ◽  
J. Roth ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Amorphous Structure ◽  
Solid Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
Electrolyte Film ◽  
Plasma Sprayed

ABSTRACTAn intermediate temperature solid oxide fuel cell (SOFC) electrolyte film of La0.8Sr 0.2Ga0.8Mg0.2O2.8 (LSGM) was fabricated using a plasma spray process. The microstructure and phase were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical behavior of the thermal sprayed LSGM film was investigated using electrochemical impedance spectroscopy (EIS). The study indicates that thermal spray can deposit a dense LSGM layer. It was found that the rapid cooling in the thermal process led to an amorphous or poor crystalline LSGM deposited layer. This amorphous structure has a significant effect on the performance of the cell. Crystallization of the deposited LSGM layer was observed during annealing between 500–600 °C. After annealing at 800 °C, the ionic conductivity of the sprayed LSGM layer can reach the same level as that of the sintered LSGM.

Sign in / Sign up

Export Citation Format

Share Document