Structure and Electrochemical Behavior of Plasma-Sprayed LSGM Electrolyte Films

2002 ◽  
Vol 756 ◽  
Author(s):  
H. Zhang ◽  
X. Ma ◽  
J. Dai ◽  
S. Hui ◽  
J. Roth ◽  
...  
Keyword(s):  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Amorphous Structure ◽  
Solid Oxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
Electrolyte Film ◽  
Plasma Sprayed

ABSTRACTAn intermediate temperature solid oxide fuel cell (SOFC) electrolyte film of La0.8Sr 0.2Ga0.8Mg0.2O2.8 (LSGM) was fabricated using a plasma spray process. The microstructure and phase were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical behavior of the thermal sprayed LSGM film was investigated using electrochemical impedance spectroscopy (EIS). The study indicates that thermal spray can deposit a dense LSGM layer. It was found that the rapid cooling in the thermal process led to an amorphous or poor crystalline LSGM deposited layer. This amorphous structure has a significant effect on the performance of the cell. Crystallization of the deposited LSGM layer was observed during annealing between 500–600 °C. After annealing at 800 °C, the ionic conductivity of the sprayed LSGM layer can reach the same level as that of the sintered LSGM.

Microstructure Characteristics, Tribology and Nano-Hardness of Plasma Sprayed NiCrRe Coating

2020 ◽  
Vol 405 ◽  
pp. 430-434
Author(s):  
Dávid Medved ◽  
Michal Ivor ◽  
Tomasz Chmielewski ◽  
Dariusz Golański ◽  
Katarzyna Pietrzak ◽  
...  
Keyword(s):  
Atmospheric Pressure ◽  
Steel Substrate ◽  
Indentation Modulus ◽  
Boiler Steel ◽  
X Ray ◽  
Spray Process ◽  
Plasma Spray Process ◽  
The Coefficient Of Friction ◽  
Continuous Stiffness Measurement ◽  
Plasma Sprayed

This paper presents the results of the investigation of NiCrRe coating deposited by plasma spray process at the atmospheric pressure on boiler steel substrate. These coatings were characterized by means of a scanning electron microscopy, and Energy-dispersive X-ray spectroscopy. The wear resistance of plasma sprayed NiCrRe coatings has been investigated under dry sliding conditions at applied load of 10 N in air. The continuous stiffness measurement (CSM) method was used for the investigation of nanohardness using Agilent G200 Nano-indenter in order to determine the mechanical properties of the coatings. Microstructural observations pointed out that the NiCr layer with white isles of rhenium possessed porosity, oxidized, un-melted and semi-melted particles, and inclusions. According to the results the thickness of the layer is 450 µm, the indentation modulus 158 ± 24.4 GPa, hardness 3.74 ± 0.76 GPa and the coefficient of friction is 0.45.

Preparation and properties of solid electrolyte CaxBi1.7−xW0.3O3.45−0.5x electrolyte material by sol–gel combution method

2019 ◽  
Vol 12 (05) ◽  
pp. 1951001
Author(s):  
Jie Yang ◽  
Changan Tian ◽  
Yu Wang ◽  
Junjie Meng ◽  
Dongdong Ji ◽  
...  
Keyword(s):  
Solid Oxide Fuel Cells ◽  
Electrochemical Impedance ◽  
Sol Gel ◽  
Combustion Method ◽  
Solid Oxide ◽  
Electrochemical Studies ◽  
Oxide Fuel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Differential Thermogravimetric Analysis

CaxBi[Formula: see text]W[Formula: see text]O[Formula: see text] (CBW) ([Formula: see text], 0.05, 0.10, 0.15, 0.20, 0.30) electrolyte material were synthesized by sol–gel self-combustion method. The samples were characterized by thermogravimetric-differential thermogravimetric analysis(TG-DSC), X-ray diffraction, scanning electron microscopy (SEM), porosity and electrochemical impedance spectroscopy (EIS). The results show the powders CaxBi[Formula: see text]W[Formula: see text]O[Formula: see text] (CBW) with fluorite crystal structure can be obtained after the precursor was calcined at 760∘C. When sintered at 780∘C for 2[Formula: see text]h, the compact ceramic sintered with relative density higher than 97% can be obtained. The electrochemical studies showed that CaxBi[Formula: see text]W[Formula: see text]O[Formula: see text] (CBW) have high ionic conductivity after 780∘C sintering. The sample Ca[Formula: see text]Bi[Formula: see text]W[Formula: see text]O[Formula: see text] exhibits a conductivity of 0.07978 S[Formula: see text][Formula: see text][Formula: see text]cm[Formula: see text] at 750∘C, and the activation energy is 0.845[Formula: see text]eV, which is expected to be applied to the electrolyte materials for intermediate temperature solid oxide fuel cells (SOFC).

Preparation and Performance of Co3O4/Polyaniline Nano-Composite for Supercapacitor

2011 ◽  
Vol 239-242 ◽  
pp. 2042-2045 ◽  
Author(s):  
Shu Ping Yu ◽  
Xiao Cong Chang ◽  
Zhong Ming Wang ◽  
Ke Fei Han ◽  
Hong Zhu
Keyword(s):  
Cyclic Voltammetry ◽  
Emulsion Polymerization ◽  
Cobalt Oxide ◽  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Nano Composite ◽  
X Ray ◽  
Scan Rate ◽  
And Performance

Cobalt oxide-Polyaniline (Co3O4/PANI) nanocomposites were prepared via inverted emulsion polymerization. The structure of the obtained composites were characterized by X-ray diffraction (XRD). The electrochemical behavior was studied by cyclic voltammetry(CV) and electrochemical impedance spectrometry(EIS) experiments. The Co3O4/PANI(1:2) composite calcined at 400°C exhibits the highest capacitance value of 357 F/g at the scan rate of 5mV/s.

Effect of Zn Content on Structure, Roughness and Corrosion Behavior of Zn-Ni Alloys

2019 ◽  
Vol 17 (17) ◽  
pp. 17-22
Author(s):  
Hayette Faid
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Stripping Voltammetry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Alloys ◽  
Sulfate Bath ◽  
Zn Content ◽  
Polarization Test ◽  
Δ Phase

AbstractIn this work, Zn-Ni alloys have been deposited on steel from sulfate bath, by electrodeposition method. The effect of Zn content on deposits properties was studied by cyclic voltammetry (CV), chronoaperometry (CA), linear stripping voltammetry (ALSV) and diffraction (XRD) and scanning electronic microscopy (SEM). The corrosion behavior in 3.5 wt. NaCl solution was examined using anodic polarization test and electrochemical impedance spectroscopy. X-ray diffraction of show that Zn-Ni alloys structure is composed of δ phase and γ phase, which increase with the decrease of Zn content in deposits. Results show that deposits obtained from bath less Zn2+ concentration exhibited better corrosion resistance.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

scholarly journals A Study of Thin Film Resistors Prepared Using Ni-Cr-Si-Al-Ta High Entropy Alloy

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Ruei-Cheng Lin ◽  
Tai-Kuang Lee ◽  
Der-Ho Wu ◽  
Ying-Chieh Lee
Keyword(s):  
Annealing Temperature ◽  
Phase Evolution ◽  
Amorphous Structure ◽  
High Entropy Alloy ◽  
X Ray Diffraction ◽  
Temperature Coefficient Of Resistance ◽  
X Ray ◽  
High Entropy ◽  
Transmission Electron ◽  
Thin Film Resistors

Ni-Cr-Si-Al-Ta resistive thin films were prepared on glass and Al2O3substrates by DC magnetron cosputtering from targets of Ni0.35-Cr0.25-Si0.2-Al0.2casting alloy and Ta metal. Electrical properties and microstructures of Ni-Cr-Si-Al-Ta films under different sputtering powers and annealing temperatures were investigated. The phase evolution, microstructure, and composition of Ni-Cr-Si-Al-Ta films were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and Auger electron spectroscopy (AES). When the annealing temperature was set to 300°C, the Ni-Cr-Si-Al-Ta films with an amorphous structure were observed. When the annealing temperature was at 500°C, the Ni-Cr-Si-Al-Ta films crystallized into Al0.9Ni4.22, Cr2Ta, and Ta5Si3phases. The Ni-Cr-Si-Al-Ta films deposited at 100 W and annealed at 300°C which exhibited the higher resistivity 2215 μΩ-cm with −10 ppm/°C of temperature coefficient of resistance (TCR).

scholarly journals Effect of Molybdenum Content on the Corrosion and Microstructure of Low-Ni, Co-Free Maraging Steels

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 852
Author(s):  
Asiful H. Seikh ◽  
Hossam Halfa ◽  
Mahmoud S. Soliman
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Microstructural Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Alloying Element ◽  
X Ray ◽  
Maraging Steels ◽  
Eds Analysis ◽  
Electroslag Refining

Molybdenum (Mo) is an important alloying element in maraging steels. In this study, we altered the Mo concentration during the production of four cobalt-free maraging steels using an electroslag refining process. The microstructure of the four forged maraging steels was evaluated to examine phase contents by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. Additionally, we assessed the corrosion resistance of the newly developed alloys in 3.5% NaCl solution and 1 M H2SO4 solution through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Furthermore, we performed SEM and energy-dispersive spectroscopy (EDS) analysis after corrosion to assess changes in microstructure and Raman spectroscopy to identify the presence of phases on the electrode surface. The microstructural analysis shows that the formation of retained austenite increases with increasing Mo concentrations. It is found from corrosion study that increasing Mo concentration up to 4.6% increased the corrosion resistance of the steel. However, further increase in Mo concentration reduces the corrosion resistance.

Few-Layered MoS2 Nanostructures for Highly Efficient Visible Light Photocatalysis

NANO ◽  
2016 ◽  
Vol 11 (10) ◽  
pp. 1650114 ◽  
Author(s):  
Dan Li ◽  
Jianwei Li ◽  
Caiqin Han ◽  
Xinsheng Zhao ◽  
Haipeng Chu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Electrochemical Impedance ◽  
X Ray Diffraction ◽  
Electron Hole ◽  
Electrochemical Impedance Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Hole Pair

Few-layered MoS2 nanostructures were successfully synthesized by a simple hydrothermal method without the addition of any catalysts or surfactants. Their morphology, structure and photocatalytic activity were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, electrochemical impedance spectra and UV-Vis absorption spectroscopy, respectively. These results show that the MoS2 nanostructures synthesized at 180[Formula: see text]C exhibit an optimal visible light photocatalytic activity (99%) in the degradation of Rhodamine B owing to the relatively easier adsorption of pollutants, higher visible light absorption and lower electron–hole pair recombination.

Substrate Temperature and La0.9Sr0.1Ga0.8Mg0.2O3-δ Electrolyte Film Growth by Radio Frequency Magnetron Sputtering

2015 ◽  
Vol 833 ◽  
pp. 127-133
Author(s):  
Jie Yu ◽  
Jie Xing ◽  
Xiu Hua Chen ◽  
Wen Hui Ma ◽  
Rui Li ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Radio Frequency ◽  
Film Growth ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrolyte Film ◽  
Porous Anode

La0.9Sr0.1Ga0.8Mg0.2O3-δ (LSGM) electrolyte thin films were fabricated on La0.7Sr0.3Cr0.5Mn0.5O2.75 (LSCM) porous anode substrates by Radio Frequency (RF) magnetron sputtering method. The compatibility between LSGM and LSCM was examined. Microstructures of LSGM thin films fabricated were observed by scanning electron microscope (SEM). The effect of substrate temperature on LSGM thin films was clarified by X-ray Diffraction (XRD). Deposition rate increases firstly at the range of 50°C~150°C, and then decreases at the range of 150°C ~300°C. After annealing, perovskite structure with the same growth orientation forms at different substrate temperature. Crystallite size decreases at first, to the minimum point at 150°C, then increases as substrate temperature rises.

Material Characteristics and Electrical Modeling of Ultra Thin Copper Oxides in ULSI Application

2007 ◽  
Vol 561-565 ◽  
pp. 1225-1228
Author(s):  
Takayuki Ohba
Keyword(s):  
Diffraction Pattern ◽  
Barrier Height ◽  
Oxide Thickness ◽  
Amorphous Structure ◽  
Emission Model ◽  
X Ray Diffraction ◽  
Edge Structure ◽  
X Ray ◽  
Current Emission ◽  
X Ray Absorption

With the highest brilliance synchrotron radiation X-ray (SPring-8) and TEM observations, Cu oxides ranged 2-nm to 10-nm in thickness formed on sputtered Cu has been evaluated. For the plasma-assisted Cu oxide, weak Cu2O and/or CuO X-ray diffraction pattern is observed, while no diffraction pattern in native and thermally (170°C) grown oxides. Those native and thermal oxides show Cu2O coordination observed by XANES (X-ray Absorption Near Edge Structure) method. This suggests that Cu oxide formed at low temperatures consists of stoichiometric Cu2O in an amorphous structure. According to the Fowler-Nordheim (F-N) current emission model, the current emission taking place at Cu2O decreases with increasing of the oxide thickness and its mean barrier height (φB) in the MIM band structure. In case of current density at 106A/cm2 of 1V, it is estimated that the allowable thickness of Cu oxides is approximately 1.5-nm at 1 eV of barrier height.

Sign in / Sign up

Export Citation Format

Share Document