scholarly journals The Effects of Natural Paint on the Moisture Buffering Ability of Paper Plaster

2020 ◽  
Vol 57 (5) ◽  
pp. 51-60
Author(s):  
N. Nutt ◽  
A. Kubjas ◽  
L. Nei ◽  
A. Ruus
Keyword(s):  
Relative Humidity ◽  
Indoor Air ◽  
Waste Paper ◽  
Moisture Permeability ◽  
Daily Variations ◽  
Number Of Layers ◽  
Buffer Value ◽  
Moisture Buffering ◽  
Moisture Buffer Value

AbstractThe scope of the Nordtest method is to evaluate the moisture buffer value (MBV) of materials exposed to indoor air. The test is intended to simulate daily variations with relative humidity (RH) between 75 % during 8 hours and 33 % during 16 hours.The specimens follow a recipe that consists of waste paper, glue and water. Specimens made of paper plaster were covered with different colours.The results of the experiment showed that the type of paint used and the number of layers applied affected the MBV. Natural colours have a better moisture permeability than chemical paints, but the number of natural colour layers affects the MBV. The higher the number of layers, the lower the MBV.

scholarly journals Moisture Buffer Value of Composite Material Made of Clay- Sand Plaster and Wastepaper

2020 ◽  
Vol 27 (2) ◽  
pp. 108-115
Author(s):  
Nele Nutt ◽  
Ardo Kubjas
Keyword(s):  
Composite Material ◽  
Relative Humidity ◽  
Indoor Air ◽  
Large Percentage ◽  
Waste Paper ◽  
Daily Variations ◽  
Impressive Result ◽  
Buffer Value ◽  
Moisture Buffer Value

The scope of the Nordtest method is to evaluate the moisture buffer value (MBV) for materials exposed to indoor air. The test is intended to simulate daily variations with relative humidity (RH) of 75% during 8 hours and 33% during 16 hours.Many authors have noted that clay plaster has a very good MBV (Altmäe et al. 2019). Our previous tests have shown that the MBV of clay plaster can be increased by adding paper plaster mixture (Nutt et al. 2020a). The specimen made according to a recipe contains the following: waste paper, glue, clay plaster mixture and water. Eleven paper plaster mixtures with different percentages were used.Test results showed that a large percentage of paper in the plaster increases the MBV. An impressive result, which needs to be studied further, was that the MBV was the highest in the mixture that consisted of 80% paper.

scholarly journals A mathematical model for predicting the indoor moisture variation by using moisture buffering theory

2021 ◽  
Vol 2069 (1) ◽  
pp. 012036
Author(s):  
Kan Zu ◽  
Menghao Qin
Keyword(s):  
Mathematical Model ◽  
Energy Consumption ◽  
Indoor Air ◽  
Building Materials ◽  
Air Humidity ◽  
Acceptable Solution ◽  
Moisture Variation ◽  
Buffer Value ◽  
Moisture Buffering ◽  
Moisture Buffer Value

Abstract Indoor air humidity evaluation plays an of great importance role on the thermal comfort and building energy consumption. The utilization of hygroscopic materials as building materials acts on the indoor air humidity by regulating its humidity fluctuations, and then reduces a certain fraction of energy consumption on the air conditioning systems. Based on the Fick’s law, the physical process inside these hygroscopic materials requires the determinations of hygrothermal properties, which signify the extensive and reiterative experiments. While in many building simulation toolboxes, moisture buffering behavior has been evaluated by either simple approximations or complicated heat and mass model. In this case, we developed a mathematical model about the moisture transport with acceptable solution time and accuracy in terms of the moisture buffer value (MBV) theory. Considering that MBV originally represents the moisture buffering capacity of those hygroscopic materials, we did some mathematical deduction about MBVs under different boundary conditions. Then the definition of time-average MBV has been used, and all the required parameters was obtained from the practical MBV test. By comparing the new moisture buffer value model (MBM) with HAMT model, the results indicated that MBM could provide reasonably accurate prediction for indoor moisture variation.

scholarly journals Moisture Buffering of Multilayer Internal Wall Assemblies at the Micro Scale: Experimental Study and Numerical Modelling

2019 ◽  
Vol 9 (16) ◽  
pp. 3438 ◽  
Author(s):  
Dobrosława Kaczorek
Keyword(s):  
Penetration Depth ◽  
Buffering Capacity ◽  
Internal Wall ◽  
Simplified Method ◽  
Buffer Value ◽  
Series Of Experiments ◽  
Overall Performance ◽  
Wall Assembly ◽  
Moisture Buffering ◽  
Moisture Buffer Value

In this paper, a series of experiments assessing the moisture buffer value (MBV) of four internal wall assembly samples made from hygroscopic materials was performed. A modified Nordtest protocol was used. Moisture buffer values of all the investigated wall assemblies, with varying moisture loads in the range of 50% to 80%, showed a moderate moisture buffer value (MBV: 0.5–1.0 (g·m−2·%RH−1)). The results showed that in a wall assembly where the MBV of the whole assembly is lower than the MBV of the outer layers, the moisture-buffering capacity of the inner layer is untapped. Outer layers affect inner layers by changing their moisture-buffering capacity, which in turn changes the overall performance of the whole assembly. In addition, it was observed that if the penetration depth value of the outer layer is greater than its thickness, vapour reaches into the deeper layer and wall assemblies made of layers with materials characterized by a lower value of penetration depth reach steady state more slowly. The WUFI Pro tool was used to compare the simulated and experimental results. Despite the discrepancies between these results, it offers a simplified method, helping designers make decisions about which materials to choose to improve the moisture-buffering effect.

Study of Moisture Buffering in Building Materials with Application of Sorption Kinetics Models

2010 ◽  
Vol 297-301 ◽  
pp. 1232-1237 ◽  
Author(s):  
N.M.M. Ramos ◽  
João M.P.Q. Delgado ◽  
V.P. de Freitas
Keyword(s):  
Building Materials ◽  
Moisture Absorption ◽  
Stationary Process ◽  
Sorption Kinetics ◽  
Temperature Level ◽  
Kinetics Models ◽  
Buffer Value ◽  
Experimental Values ◽  
Moisture Buffering ◽  
Moisture Buffer Value

This work presents experimental values of Moisture Buffer Value (MBV) obtained with three different samples of building materials, using a non-stationary process of moisture absorption. The tests carried out at the laboratory tried to explore the importance of some of the variables that can interfere in the final results, such as materials themselves, temperature level and the use of finishing coatings. The experimental data obtained at 15°C and 23°C were then analyzed using the second order sorption kinetic model. The application of kinetics models to the experimental results was explored and several parameters were retrieved. A proposal for the use of these parameters is presented and its practical use is discussed.

scholarly journals Indoor Air Quality (IAQ): Accuracy of Natural Ventilation for Temperature, Air Flow Rate and Relative Humidity (RH) in School Building Classrooms

2018 ◽  
Vol 7 (3.9) ◽  
pp. 42
Author(s):  
Norsafiah Norazman ◽  
Adi Irfan Che Ani ◽  
Nor Haslina Ja’afar ◽  
Muhamad Azry Khoiry
Keyword(s):  
Air Quality ◽  
Relative Humidity ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Air Flow ◽  
Weather Conditions ◽  
Potential Health ◽  
The Hours ◽  
Hot Weather

Indoor Air Quality (IAQ) is an essential matter in achieving students’ satisfaction for the learning process. Building’s orientation is a factor that may encourage sufficient natural ventilation for the classroom occupants. Inadequate ventilation is an issue for most existing classrooms. The purpose of this paper is to analyze the accuracy of natural ventilation in classrooms. Therefore, experimental on 20 classrooms has been conducted by using Multipurpose Meter at secondary school buildings in Malaysia. The findings indicated that the accuracy of natural ventilation testing was below the permissible limits throughout the hours monitored, thus this may cause potential health hazards to the students. Temperature and air flow rates were lower than 23 °C and 0.15 m/s respectively, it fulfilled the basic requirements as a standard learning environment. However, measurements taken showed the overall relative humidity (RH) in the classrooms can be categorized as acceptable with 40% to 70% range. On the basis of these findings, it is evident that naturally ventilated classrooms are important especially due to energy efficiency, whereas mechanical ventilation should only be installed as an alternative under extremely hot weather conditions.   

scholarly journals Indoor Particulate Matter (PM2.5) and Comfort Parameters in a University Building

2020 ◽  
Vol 8 (2) ◽  
pp. 61-67
Author(s):  
Nurul Bahiyah Abd Wahid ◽  
Intan Idura Mohamad Isa ◽  
Ahmad Khairuddin Hassan ◽  
Muhammad Izzat Iman Razali ◽  
Ahmad Haziq Hasrizal ◽  
...  
Keyword(s):  
Particulate Matter ◽  
Relative Humidity ◽  
Indoor Air ◽  
National Policy ◽  
Lecture Hall ◽  
Airborne Microorganisms ◽  
Code Of Practice ◽  
The Mean ◽  
Indoor Particulate Matter ◽  
Comfort Parameters

This study aims to determine the particulate matter (PM2.5) mass concentrations and the comfort parameters (total bacterial counts (TBC), total fungal counts (TFC), relative humidity and temperature) in a university building. The samplings were carried out in three different indoor areas, including lecture hall, laboratory and lecturer office. PM2.5 samples were collected over a period of 8 h sampling using a low volume sampler (LVS). The anemometer Model Kestrel 0855YEL was used to measure relative humidity and temperature parameters. The sampling of airborne microorganisms was conducted by using microbial sampler at 350 L air sampled volume. The results showed that the highest average of PM2.5 was at lecture hall (88.54 ± 26.21 µgm-3) followed by lecturer office (69.79 ± 19.06 µgm-3) and laboratory (47.92 ± 24.88 µgm-3). The mean of TBC and TFC readings recorded as follow; 32.71 ± 5.91 cfu m-3 and 76.71 ± 21.5 cfu m-3 for laboratory, 112.1 ± 29.06 cfu m-3 and 124.67 ± 23.35 cfu m-3 for lecturer office, 121.74 ± 19.33 cfu m-3 and 115.33 ± 8.08 cfu m-3 for lecture hall. The average of all comfort parameter was within the prescribed standard by Industry Code of Practice on Indoor Air Quality 2010 for all sampling sites. Therefore, all occupants of the building can work in a conducive and comfortable environment. This study is in line with the objectives of National Policy on the Environment (DASN), which focusing on achieving a clean, safe, healthy and productive environment for present and future generations.

scholarly journals Microbiome in an Office Building Using a Cooling Trench as an Outdoor Air Duct

2019 ◽  
Vol 111 ◽  
pp. 06045
Author(s):  
Mizuki Niimura ◽  
U Yanagi
Keyword(s):  
Relative Humidity ◽  
Energy Saving ◽  
Air Temperature ◽  
Indoor Air ◽  
Principal Coordinate Analysis ◽  
Office Building ◽  
Metagenomic Analysis ◽  
Outdoor Air ◽  
Energy Saving Technique ◽  
Building Cooling

Subterranean temperature at a depth of 10 m is almost equal to the average outdoor air temperature of the same area. Therefore, if a building cooling trench is used as an outdoor air duct, outdoor air can be cooled in summer and warmed in winter. This energy-saving technique is often used in Japan. However, since the relative humidity in a cooling trench is high, microbe numbers tend to increase in summer. The present study sought to characterize the microbiome status in the cooling trench of such an office building in Japan. Specifically, we performed a metagenomic analysis in which we analyzed DNA directly upon collection from the environment, without intervening cultivation. The results showed the presence of bacteria of the genera Pseudomonas, Lactobacillus, Nesterenkonia, Staphylococcus, Deinococcus, Acinetobacter, Enhydorobacter, and Corynebacterium. Bacteria of the genera Nesterenkonia, Deinococcus, Enhydorobacter, and Corynebacterium predominated on the surface of the trench. Notably, bacteria of the genus Nesterenkonia constituted >50% of the organisms on the surface of the downstream end of the cooling trench. Principal coordinate analysis was used to compare bacterial inhabitants of outdoor air, indoor air from 2nd- and 3rdfloor offices, and the region downstream of the cooling trench. The results suggested that the microbiome of air in this cooling trench influenced indoor air within the building.

Study on the Liquid Refrigerant Defrosting System and the Defrosting Rule

2018 ◽  
Vol 10 (5) ◽  
Author(s):  
Meng Wang ◽  
Runqing Zang ◽  
Hai Feng ◽  
Chaoqun Yu ◽  
He Wang ◽  
...  
Keyword(s):  
Relative Humidity ◽  
Cold Storage ◽  
Indoor Air ◽  
Storage Temperature ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Theoretical Research ◽  
Compressor Power ◽  
The Relationship ◽  
Fin Spacing

The liquid refrigerant defrosting (LRD) is a defrosting method which leads the liquid refrigerant in the high-pressure reservoir to the frosting evaporator. The refrigeration process is continuous during the defrosting period, which increases the defrosting frequency. Compared with the traditional defrosting method, no large fin spacing should be left to reduce the defrosting frequency. The system can recover all the defrosting cooling capacity to improve the subcooling, so that the indoor air temperature fluctuations are avoided. In order to explore the effect and the rule of the LRD, the defrosting experiments were carried out in different frosting mass under the condition of the cold storage temperature of −20 °C. The defrosting time, temperature rise value, cooling capacity, and compressor power consumption value were calculated at the different frosting mass. Interpolation and applying the curve fitting equation helps to obtain remaining values. The relative humidity was calculated by the frosting mathematical model. Finally, the relationship between the coefficient of performance (COP) and the defrosting cycle (the sum of the defrosting time and the frosting time) was obtained. The experiments and theoretical research showed that the fluctuating value of cold storage temperature was about 5 °C and the defrosting time was about 30 min during the defrosting process. In the case of the relative humidity of 70%, 80%, 90%, the optimum defrosting cycle of the experiment was 16.4, 10.9, 7.5 h and the frosting mass was 2.66, 2.90, 3.22 kg, and the maximum COP was 1.51, 1.48, 1.45.

scholarly journals Probabilistic modeling of the indoor climates of residential buildings using EnergyPlus

2017 ◽  
Vol 41 (3) ◽  
pp. 225-246 ◽  
Author(s):  
Elizabeth Buechler ◽  
Simon Pallin ◽  
Philip Boudreaux ◽  
Michaela Stockdale
Keyword(s):  
Relative Humidity ◽  
Air Temperature ◽  
Indoor Air ◽  
Air Conditioning ◽  
Residential Buildings ◽  
The United States ◽  
Climate Data ◽  
Indoor Climate ◽  
Oak Ridge ◽  
Simulation Engine

The indoor air temperature and relative humidity in residential buildings significantly affect material moisture durability, heating, ventilation, and air-conditioning system performance, and occupant comfort. Therefore, indoor climate data are generally required to define boundary conditions in numerical models that evaluate envelope durability and equipment performance. However, indoor climate data obtained from field studies are influenced by weather, occupant behavior, and internal loads and are generally unrepresentative of the residential building stock. Likewise, whole-building simulation models typically neglect stochastic variables and yield deterministic results that are applicable to only a single home in a specific climate. The purpose of this study was to probabilistically model homes with the simulation engine EnergyPlus to generate indoor climate data that are widely applicable to residential buildings. Monte Carlo methods were used to perform 840,000 simulations on the Oak Ridge National Laboratory supercomputer (Titan) that accounted for stochastic variation in internal loads, air tightness, home size, and thermostat set points. The Effective Moisture Penetration Depth model was used to consider the effects of moisture buffering. The effects of location and building type on indoor climate were analyzed by evaluating six building types and 14 locations across the United States. The average monthly net indoor moisture supply values were calculated for each climate zone, and the distributions of indoor air temperature and relative humidity conditions were compared with ASHRAE 160 and EN 15026 design conditions. The indoor climate data will be incorporated into an online database tool to aid the building community in designing effective heating, ventilation, and air-conditioning systems and moisture durable building envelopes.

Sign in / Sign up

Export Citation Format

Share Document