scholarly journals Experimental Assessment if Changes in Structural Steel Composition by Progressive Technology Cutting

2021 ◽  
Vol 29 (4) ◽  
pp. 266-273
Author(s):  
Jozef Mascenik
Keyword(s):  
Sample Preparation ◽  
Structural Steel ◽  
Hardness Measurement ◽  
Experimental Sample ◽  
Plasma Technology ◽  
Steel Composition ◽  
Experimental Assessment ◽  
Experimental Part ◽  
Photo Documentation ◽  
Progressive Technology

Abstract The submitted paper deals with the issue of change in structure, hardness and thermally affected zone of the samples of a toothed wheel part produced by technology of cutting by plasma, laser and water jet. The cutting process by laser and plasma technology causes intensive thermal affection of material and change in structure and microhardness in the cutting area referred to as thermally affected zone. The paper describes three material cutting technologies of the toothed wheel part. The experimental part contains description of experimental sample preparation, its hardness measurement and examination of structure along with further evaluation through graphs and photo documentation of structures.

scholarly journals Ultrasonic Inspection Techniques Possibilities for Centrifugal Cast Copper Alloy

2017 ◽  
Vol 17 (2) ◽  
pp. 35-38 ◽  
Author(s):  
R. Konar ◽  
M. Mician
Keyword(s):  
Ultrasonic Testing ◽  
Copper Alloy ◽  
Ultrasonic Attenuation ◽  
Ultrasonic Inspection ◽  
Single Element ◽  
Experimental Sample ◽  
Centrifugally Cast ◽  
Experimental Part ◽  
Conventional Ultrasound ◽  
Inspection Techniques

Abstract The article deals with ultrasonic testing possibilities of the copper alloy centrifugal casts. It focused on the problems that arise when testing of castings is made of non-ferrous materials. Most common types of casting defects is dedicated in theoretical introduction of article. Ultrasonic testing technique by conventional ultrasound system is described in the theoretical part too. Practical ultrasonic testing of centrifugal copper alloy cast - brass is in experimental part. The experimental sample was part of centrifugally cast brass ring with dimensions of Ø1200x34 mm. The influence of microstructure on ultrasonic attenuation and limitations in testing due to attenuation is describes in experimental part. Conventional direct single element contact ultrasound probe with frequencies of 5 MHz, 3.5 MHz and 2 MHz were used for all experimental measurements. The results of experimental part of article are recommendations for selecting equipment and accessories for casting testing made of non-ferrous metals.

Pollutant Identification by Selected Area Electron Diffraction

1974 ◽  
Vol 32 ◽  
pp. 532-533
Author(s):  
R. E. Ferrell ◽  
G. G. Paulson ◽  
C. W. Walker
Keyword(s):  
Thermal Treatment ◽  
Electron Diffraction ◽  
Sample Preparation ◽  
Crystal Structures ◽  
Water Samples ◽  
Environmental Samples ◽  
Short Review ◽  
Selected Area Electron Diffraction ◽  
Multiple Component

Selected area electron diffraction (SAD) has been used successfully to determine crystal structures, identify traces of minerals in rocks, and characterize the phases formed during thermal treatment of micron-sized particles. There is an increased interest in the method because it has the potential capability of identifying micron-sized pollutants in air and water samples. This paper is a short review of the theory behind SAD and a discussion of the sample preparation employed for the analysis of multiple component environmental samples.

Preparation of Thin Cadmium Telluride Samples for Electron Microscope Studies

1974 ◽  
Vol 32 ◽  
pp. 548-549
Author(s):  
T. J. Magee ◽  
J. Peng ◽  
J. Bean
Keyword(s):  
Electron Microscope ◽  
Sulfuric Acid ◽  
Solid State ◽  
Sample Preparation ◽  
Cadmium Telluride ◽  
Potassium Dichromate ◽  
Optical Components ◽  
The Past ◽  
Solid State Devices

Cadmium telluride has become increasingly important in a number of technological applications, particularly in the area of laser-optical components and solid state devices, Microstructural characterizations of the material have in the past been somewhat limited because of the lack of suitable sample preparation and thinning techniques. Utilizing a modified jet thinning apparatus and a potassium dichromate-sulfuric acid thinning solution, a procedure has now been developed for obtaining thin contamination-free samples for TEM examination.

A Freeze Shadow Technique for the Preparation of Soft Paint Latexes for Electron Microscopy

1977 ◽  
Vol 35 ◽  
pp. 314-315
Author(s):  
Earl R. Walter ◽  
Glen H. Bryant
Keyword(s):  
Sample Preparation ◽  
High Vacuum ◽  
Vacuum System ◽  
Latex Particles ◽  
New Methods ◽  
Diffusion Pump ◽  
Film Forming ◽  
Routine Basis ◽  
Distribution Studies ◽  
Preparation Techniques

With the development of soft, film forming latexes for use in paints and other coatings applications, it became desirable to develop new methods of sample preparation for latex particle size distribution studies with the electron microscope. Conventional latex sample preparation techniques were inadequate due to the pronounced tendency of these new soft latex particles to distort, flatten and fuse on the substrate when they dried. In order to avoid these complications and obtain electron micrographs of undistorted latex particles of soft resins, a freeze-dry, cold shadowing technique was developed. The method has now been used in our laboratory on a routine basis for several years.The cold shadowing is done in a specially constructed vacuum system, having a conventional mechanical fore pump and oil diffusion pump supplying vacuum. The system incorporates bellows type high vacuum valves to permit a prepump cycle and opening of the shadowing chamber without shutting down the oil diffusion pump. A baffeled sorption trap isolates the shadowing chamber from the pumps.

SEM evaluation of the TEM cold-stage double-film specimen

1984 ◽  
Vol 42 ◽  
pp. 272-273
Author(s):  
Jayesh Bellare
Keyword(s):  
Spatial Distribution ◽  
Sample Preparation ◽  
Sample Thickness ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Liquid Sample ◽  
Thin Specimen ◽  
Sample Preparation Technique ◽  
Cold Stage ◽  
Film Specimen

Seeing is believing, but only after the sample preparation technique has received a systematic study and a full record is made of the treatment the sample gets.For microstructured liquids and suspensions, fast-freeze thermal fixation and cold-stage microscopy is perhaps the least artifact-laden technique. In the double-film specimen preparation technique, a layer of liquid sample is trapped between 100- and 400-mesh polymer (polyimide, PI) coated grids. Blotting against filter paper drains excess liquid and provides a thin specimen, which is fast-frozen by plunging into liquid nitrogen. This frozen sandwich (Fig. 1) is mounted in a cooling holder and viewed in TEM.Though extremely promising for visualization of liquid microstructures, this double-film technique suffers from a) ireproducibility and nonuniformity of sample thickness, b) low yield of imageable grid squares and c) nonuniform spatial distribution of particulates, which results in fewer being imaged.

Advanced TEM sample preparation techniques for submicron Si devices

1995 ◽  
Vol 53 ◽  
pp. 516-517 ◽  
Author(s):  
P. B. Basham ◽  
H. L. Tsai
Keyword(s):  
Sample Preparation ◽  
Process Development ◽  
Light Transmission ◽  
Specific Area ◽  
Turnaround Time ◽  
Small Hole ◽  
Area Of Interest ◽  
Transmission Electron ◽  
Polished Side ◽  
Preparation Techniques

The use of transmission electron microscopy (TEM) to support process development of advanced microelectronic devices is often challenged by a large amount of samples submitted from wafer fabrication areas and specific-spot analysis. Improving the TEM sample preparation techniques for a fast turnaround time is critical in order to provide a timely support for customers and improve the utilization of TEM. For the specific-area sample preparation, a technique which can be easily prepared with the least amount of effort is preferred. For these reasons, we have developed several techniques which have greatly facilitated the TEM sample preparation.For specific-area analysis, the use of a copper grid with a small hole is found to be very useful. With this small-hole grid technique, TEM sample preparation can be proceeded by well-established conventional methods. The sample is first polished to the area of interest, which is then carefully positioned inside the hole. This polished side is placed against the grid by epoxy Fig. 1 is an optical image of a TEM cross-section after dimpling to light transmission.

Quantitative defect studies in semiconductor TEM samples prepared by low angle ion milling

1995 ◽  
Vol 53 ◽  
pp. 512-513
Author(s):  
L. Mulestagno ◽  
J.C. Holzer ◽  
P. Fraundorf
Keyword(s):  
Sample Preparation ◽  
Milling Time ◽  
High Density ◽  
Low Density ◽  
Ion Milling ◽  
High Quality ◽  
Variable Angle ◽  
Major Disadvantage ◽  
Induced Defects

Due to the wealth of information, both analytical and structural that can be obtained from it TEM always has been a favorite tool for the analysis of process-induced defects in semiconductor wafers. The only major disadvantage has always been, that the volume under study in the TEM is relatively small, making it difficult to locate low density defects, and sample preparation is a somewhat lengthy procedure. This problem has been somewhat alleviated by the availability of efficient low angle milling.Using a PIPS® variable angle ion -mill, manufactured by Gatan, we have been consistently obtaining planar specimens with a high quality thin area in excess of 5 × 104 μm2 in about half an hour (milling time), which has made it possible to locate defects at lower densities, or, for defects of relatively high density, obtain information which is statistically more significant (table 1).

Sign in / Sign up

Export Citation Format

Share Document