STUDY ON ADHESION AND BONDING PERFORMANCE BETWEEN BAMBOO AND CONCRETE

2017 ◽  
Vol 6 (3) ◽  
pp. 1
Author(s):  
KAUSHAL LOKENDRA ◽  
MAURYA MADAN CHANDRA ◽  
◽  
Keyword(s):  
Bonding Performance

Bonding performance of a self-adhering flowable composite resin to different deciduous surfaces

2019 ◽  
Vol 65 (2) ◽  
pp. 1949-2261
Author(s):  
Fatma Abdelgawad ◽  
Rasha Abdelraouf ◽  
Manar Mohammed
Keyword(s):  
Composite Resin ◽  
Flowable Composite ◽  
Bonding Performance

scholarly journals Bonding and Thermal Cycling Performances of Two (Poly)Aryl–Ether–Ketone (PAEKs) Materials to an Acrylic Denture Base Resin

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 543 ◽  
Author(s):  
Tzu-Yu Peng ◽  
Saiji Shimoe ◽  
Lih-Jyh Fuh ◽  
Chung-Kwei Lin ◽  
Dan-Jae Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Thermal Cycling ◽  
Fatigue Testing ◽  
Lower Surface ◽  
Aryl Ether ◽  
Bonding Performance ◽  
Significant Difference ◽  
Aryl Ether Ketone ◽  
Ether Ketone ◽  
Thermal Cycling Fatigue

Poly(aryl–ether–ketone) materials (PAEKs) are gaining interest in everyday dental practices because of their natural properties. This study aims to analyze the bonding performance of PAEKs to a denture acrylic. Testing materials were pretreated by grinding, sandblasting, and priming prior to polymerization with the denture acrylic. The surface morphologies were observed using a scanning electron microscope and the surface roughness was measured using atomic force microscopy. The shear bond strength (SBS) values were determined after 0 and 2500 thermal cycles. The obtained data were analyzed using a paired samples t-test and Tukey’s honestly significant difference (HSD) test (α = 0.05). The surface characteristics of testing materials after different surface pretreatments showed obvious differences. PAEKs showed lower surface roughness values (0.02–0.03 MPa) than Co-Cr (0.16 MPa) and zirconia (0.22 MPa) after priming and sandblasting treatments (p < 0.05). The SBS values of PAEKs (7.60–8.38 MPa) met the clinical requirements suggested by ISO 10477 (5 MPa). Moreover, PAEKs showed significantly lower SBS reductions (p < 0.05) after thermal cycling fatigue testing compared to Co-Cr and zirconia. Bonding performance is essential for denture materials, and our results demonstrated that PAEKs possess good resistance to thermal cycling fatigue, which is an advantage in clinical applications. The results imply that PAEKs are potential alternative materials for the removable of prosthetic frameworks.

scholarly journals Effect of rare earth oxide CeO2 on the anodic bonding performance of PEG-based MEMS encapsulation materials

2021 ◽  
Vol 13 (3) ◽  
pp. 168781402110077
Author(s):  
Chao Du ◽  
Cuirong Liu ◽  
Xu Yin ◽  
Haocheng Zhao
Keyword(s):  
Tensile Strength ◽  
Rare Earth ◽  
Rare Earth Oxide ◽  
Solid Polymer Electrolytes ◽  
Anodic Bonding ◽  
Solid Polymer ◽  
Bonding Layer ◽  
Scanning Calorimetry ◽  
Ion Migration ◽  
Bonding Performance

Herein, we synthesized a new polyethylene glycol (PEG)-based solid polymer electrolyte containing a rare earth oxide, CeO2, using mechanical metallurgy to prepare an encapsulation bonding material for MEMS. The effects of CeO2 content (0–15 wt.%) on the anodic bonding properties of the composites were investigated. Samples were analyzed and characterized by alternating current impedance spectroscopy, X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, tensile strength tests, and anodic bonding experiments. CeO2 reduced the crystallinity of the material, promoted ion migration, increased the conductivity, increased the peak current of the bonding process, and increased the tensile strength. The maximum bonding efficiency and optimal bonding layer were obtained at 8 wt% CeO2. This study expands the applications of solid polymer electrolytes as encapsulation bonding materials.

Adhesive properties of bio-based epoxy resin reinforced by cellulose nanocrystal additives

2020 ◽  
Vol 40 (4) ◽  
pp. 314-320 ◽  
Author(s):  
Tariq Aziz ◽  
Hong Fan ◽  
Xiangwei Zhang ◽  
Farman Ullah Khan ◽  
Shah Fahad ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Tensile Modulus ◽  
The Self ◽  
Environmental Engineering ◽  
Interface Area ◽  
Adhesive Properties ◽  
Composite Matrix ◽  
Bonding Performance ◽  
Good Expansion ◽  
Application Prospects

AbstractThe adhesive properties of a self-prepared bio-based epoxy resin with native cellulose nanocrystals (CNCs) are evaluated in this article. The porosity of actual CNCs is high. The most promising finding is the acquisition of high tensile modulus. The addition of CNC composites significantly increased the tensile modulus at lower wt.%, and the maximum crystallinity of CNCs was obtained. Bearing in mind the advantages of CNCs, scanning electron microscopy (SEM) showed a uniform distribution of concentrated CNCs. Clusters were formed at higher CNCs ratios, and the composite matrix content with high CNCs produced good expansion, low crystallinity, and increased elongation. Our analysis showed that the original CNCs were more evenly distributed in the self-prepared bio-based epoxy resin, which enhanced transformation, supported by improved dispersion of native CNCs. The presence of native CNCs greatly improved and enhanced the bonding performance of the bio-based epoxy resin in the interface area. Enhancing the mechanical properties of native CNCs has broad application prospects in environmental areas. This suggests that the widespread use of native CNCs in environmental engineering applications is feasible, especially in terms of adhesives properties.

Bonding performance of heat treated wood with structural adhesives

2007 ◽  
Vol 66 (3) ◽  
pp. 173-180 ◽  
Author(s):  
Milan Sernek ◽  
Michiel Boonstra ◽  
Antonio Pizzi ◽  
Aurelien Despres ◽  
Philippe Gérardin
Keyword(s):  
Treated Wood ◽  
Structural Adhesives ◽  
Bonding Performance ◽  
Heat Treated

Development of Durable Softening and Water-Repellent PP/HDPE Heat-Bondable Composite Fiber

2009 ◽  
Vol 87-88 ◽  
pp. 265-270
Author(s):  
Shi Yuan Sun ◽  
Qing Fu Zhao ◽  
Yuan Xue
Keyword(s):  
Composite Fiber ◽  
Water Repellent ◽  
Fiber Structure ◽  
Materials Properties ◽  
The Core ◽  
Bonding Performance ◽  
Finishing Process ◽  
Good Heat ◽  
Sheath Structure

Spinning and finishing techniques of a durable softening and water-repellent PP/HDPE heat-bondable fiber were introduced. The fiber has a core-sheath structure. PP is the core and HDPE is the sheath. The core-sheath fiber structure and spinning materials properties make the fiber have a good heat-bonding performance. During the finishing process the fiber got a durable softening and water-repellent quality by the durable waterproofing agent—a mixture of PMHS and PDMS. Experiments show that the fibers begin to melt and bond each other at 127.5°C and could keep a good water-repellent performance after being washed five circles.

Sign in / Sign up

Export Citation Format

Share Document