scholarly journals Thermal Performance Analysis of Parabolic Trough Solar Concentrator with Helical Tube Receiver

2018 ◽  
Vol 21 (3) ◽  
pp. 374-383 ◽  
Author(s):  
Saad Tami Hamidi ◽  
Jamal Abdul-Kareem Mohammed ◽  
Laith Mohsen Reda
Keyword(s):  
Thermal Performance ◽  
Thermal Efficiency ◽  
Water Mass ◽  
Solar Concentrator ◽  
Parabolic Trough ◽  
Heat Gain ◽  
Flow Rates ◽  
Helical Tube ◽  
Useful Heat Gain ◽  
Useful Heat

In this paper, the experimental thermal performance for a parabolic trough solar concentrator (PTSC) combined with helical tube receiver and directed by two axes solar tracking system at different amount of water flow rates has been analyzed. The experimental test results of thermal performance with regard to temperature rise of water, useful heat gain and collector thermal efficiency for the PTSC prototype at controlled water flow rates (2.3, 22.5 and 29.4 L/h) are collected. The results show that the increase of water mass flow rates causes decrease in the average water output temperature as (120.8, 63.82 and 46.08oC), respectively, the maximum outlet temperature becomes (160.5, 76, 47) oC, respectively, and thus, the average useful heat gain will be (1249.4, 732, 732.5W), respectively and the average thermal efficiency decreases as (73.021, 49.51 and 44.31 %), respectively. The experimental results show that decrease the water mass flow rate by 74.4%, causes an increase in the thermal efficiency of the PTSC by 64.7%.

The hybrid (PVT) double-pass system with a mixed-mode solar dryer for drying banana

2020 ◽  
Vol 38 (8A) ◽  
pp. 1214-1225
Author(s):  
Abdullateef A. Jadallah ◽  
Mohammed K. Alsaadi ◽  
Saeef A. Hussien
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Mixed Mode ◽  
Double Pass ◽  
Heat Gain ◽  
Pass System ◽  
Useful Heat Gain ◽  
Useful Heat

In this paper, the hybrid PVT double pass system with a mixed-mode solar dryer type under forced convection has been designed, fabricated and installed for drying crops. The dryer was tried by drying 300 grams of banana slices in the air temperature of dryer range from 43.2 to 60.2°C. The initial moisture rate of banana was about 78% and the most dropped in moisture content was from 78% to 33% after 8 hours of the drying process. The banana slices are distributed in two identical trays and it was noticed that the most and least decreasing in weight of banana samples was from 150 to 48 gram and from 150 to 55 gram in lower and upper tray respectively, when the mass flow rate as 0.031 and 0.017 kg/s, which means that the high reduction was 68% of weight banana at a high mass flow rate of airflow. The critical parameter such as temperature distribution of the PVT with dryer room, useful heat gain, and thermal efficiency are computed by using the MATLAB 2015b program built for this purpose. The optimum useful heat gain and thermal efficiency were reached 423.7  and 52.98% respectively when the solar radiation 1190  and the mass flow rate of 0.031 kg/s.

scholarly journals EXPERIMENTAL INVESTIGATION ON PARABOLIC TROUGH SOLAR COLLECTOR HOT WATER GENERATION SYSTEM

2017 ◽  
Vol 13 ◽  
pp. 09-16
Author(s):  
Vijayan Gopalsmy ◽  
R. Karunakaran
Keyword(s):  
Solar Collector ◽  
Hot Water ◽  
Generation System ◽  
Parabolic Trough ◽  
Beam Radiation ◽  
Heat Gain ◽  
Testing Period ◽  
Useful Heat Gain ◽  
Useful Heat ◽  
Parabolic Trough Solar Collector

In this work, we investigated the performance of parabolic trough solar collector with hot water generation system for 3 days day time. We observed the differences in temperature in the range of 6.7°C to 24°C.  The average beam radiation during the testing period is 658W/m2. The temperature difference, useful heat gain, wind velocity, direct beam radiation, absorber temperature and solar flux are found in the test period from 9.00 a.m to 16.00 p.m. 

Thermal Performance of a Receiver Tube for a High Concentration Ratio Parabolic Trough System and Potential for Improved Performance With Syltherm800-CuO Nanofluid

2015 ◽  
Author(s):  
Aggrey Mwesigye ◽  
Zhongjie Huan ◽  
Josua P. Meyer
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Concentration Ratio ◽  
Low Flow ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
High Concentration ◽  
Flow Rates

In this paper, the thermal performance of a high concentration ratio parabolic trough system and the potential for improved thermal performance using Syltherm800-CuO nanofluid were investigated and presented. The parabolic trough system considered in this study has a concentration ratio of 113 compared with 82 in current commercial systems. The heat transfer fluid temperature was varied between 350 K and 650 K and volume fractions of nanoparticle were in the range 1–6%. Monte-Carlo ray tracing was used to obtain the actual heat flux on the receiver’s absorber tube. The obtained heat flux profiles were subsequently coupled with a computational fluid dynamics tool to investigate the thermal performance of the receiver. From the study, the results show that with increased concentration ratios, receiver thermal performance degrades, with both the receiver heat loss and the absorber tube circumferential temperature differences increasing, especially at low flow rates. The results further show that the use of nanofluids significantly improves receiver thermal performance. The heat transfer performance increases up to 38% while the thermal efficiency increases up to 15%. Significant improvements in receiver thermal efficiency exist at high inlet temperatures and low flow rates.

Heat Transfer Performance of a Parabolic Trough Receiver Using SWCNTs-Therminol®VP-1 Nanofluids

2017 ◽  
Author(s):  
Aggrey Mwesigye ◽  
Josua P. Meyer
Keyword(s):  
Heat Transfer ◽  
Solar Energy ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Concentration Ratio ◽  
Heat Transfer Performance ◽  
Energy System ◽  
Transfer Performance ◽  
Parabolic Trough ◽  
Flow Rates

In this paper, the potential for improved thermal performance of a high concentration ratio parabolic trough solar energy system working with high thermal conductivity single-walled carbon nanotubes (SWCNTs) and Therminol®VP-1 nanofluid is numerically investigated. In the numerical analysis, the practical heat flux profiles expected for parabolic trough receivers were obtained using Monte-Carlo ray tracing and coupled with a computational fluid dynamics tool using user defined functions to investigate the thermal performance of the parabolic trough solar energy system. A parabolic trough system with a concentration ratio of 113 was considered in this study and heat transfer fluid inlet temperatures between 400 K and 650 K were used. The volume fraction of SWCNTs in the base fluid was in the range 0% to 2.5% and the flow rates used were in the range 0.82 to 69.41 m3/h. Results show improvements in the convective heat transfer performance and receiver thermal efficiency as well as a considerable reduction of the receiver thermal losses with increasing volume fractions. The heat transfer performance increases up to 64% while the thermal efficiency increases by about 4.4%. Higher increments are observed at low flow rates and inlet temperatures. The receiver thermodynamic performance also increases significantly with the use of nanofluids. Entropy generation rates reduce by about 30% for the range of parameters considered.

scholarly journals The Effect of Different Absorber Configurations On The Exergy and The Energy of Parabolic Solar Dish

2020 ◽  
Vol 7 (3) ◽  
pp. 1-13
Author(s):  
A'laa Taghi Al-Azawi ◽  
Ali A. F. Al Hamadani
Keyword(s):  
Heat Transfer ◽  
Heat Loss ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Tracking System ◽  
Open Cavity ◽  
Solar Concentrator ◽  
International Conference ◽  
National University ◽  
Parabolic Dish

Abstract— The solar energy is the most important type of energy. The parabolic dish solar collector (PDSC) is the best type among other solar collectors because it is always tracking the sun movement. The exergy and the energy performances of a PDS were analyzed experimentally and numerically. The effect of different coil geometries and different mass flow rates of heat transfer fluid (HTF) were investigated. The PDS has parabolic dish and receiver with diameter (1.5) m and (0.2) m respectively. Concentration ratio is 56.25. The parabolic polar dish was supported by a tracking system with two axes. The types of the copper absorber were used which are: (spiral –helical) coil (SHC) and spiral-conical coil (SCC). The results showed that the useful energy and thermal efficiency are varying with solar radiation variation. The useful energy varying between (480-765) W for (SHC), the thermal efficiency varying between (35.2-39.8) % for (SHC). Exergy efficiency varying between (6.9 –8.6) %. It was shown that the higher values of useful energy for (spiral – helical) absorber was 0.1L/min flow rate. REFERENCES  1. T. Taumoefolau , K. Lovegrove ," An Experimental Study of Natural Convection Heat Loss from a Solar Concentrator Cavity Receiver at Varying Orientation. ", Australian National University,, Canberra ACT 0200 AUSTRALIA.2002  2. S. PAITOONSURIKARN and K. LOVEGROVE," On the Study of Convection Loss from Open Cavity Receivers in Solar Paraboloidal Dish Applications ", Australian National University Canberra ACT 0200, AUSTRALIA, pp 154,155,2003  3. Soteris A. Kalogirou*,"Solar thermal collectors and applications", Higher Technical Institute, Progress in Energy and Combustion Science 30 (2004) 231–295, pp237, 240, 241, 2004  4. M. Prakash, S.B. Kedare, J.K. Nayak," Investigations on heat losses from a solar cavity receiver", Department of Energy Science and Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India,2008.  5. Shiva Gorjian1, Barat Ghobadian1, Teymour Tavakkoli Hashjin1, and Ahmad Banak ,"Thermal performance of a Point-focus Solar Steam Generating System ", 21st Annual International Conference on Mechanical Engineering-ISME201 7-9 May, 2013, School of Mechanical Eng., K.N.Toosi University, Tehran, Iran ,1ISME2013-1195,2013  6. Kailash Karunakaran1 Hyacinth J Kennady2 ,"Thermal Analysis of Parabolic Dish Snow Melting Device " ,International Journal for Research in Technological Studies| Vol. 1, Issue 3, February 2014 | ISSN (online): 2348-1439,2014  7. Charles-Alexis Asselineau, Ehsan Abbasi, John Pye "Open cavity receiver geometry influence on radiative losses" Australian National University (ANU), Canberra, ACT 0200 Australia. Solar2014: The 52nd Annual Conference of the Australian Solar Council 2014  8. Vahid Madadi, Touraj Tavakoli and Amir Rahimi First and second thermodynamic law analyses applied to a solar dish collector" DOI 10.1515/jnet-2014-0023 | J. Non-Equilib. Thermodyn. 2014; 39 (4):183–197  9. Yaseen. H. Mahmood , Mayadah K h. Ghaffar " Design of Solar dish concentration by using MATLAB program and Calculation of geometrical concentration parameters and heat transfer" , University of Tikrit , Tikrit , Iraq, Tikrit Journal of Pure Science 20 (4) ISSN: 1813 – 1662, 2015.  10. Vanita Thakkar, Ankush Doshi, Akshaykumar Rana "Performance Analysis Methodology for Parabolic Dish Solar Concentrators for Process Heating Using Thermic Fluid IOSR", Journal of Mechanical and Civil Engineering (IOSR-JMCE) eISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 1 Ver. II (Jan- Feb. 2015), PP 101-114  11. Saša R. pavlovi, Evangelos A. bellos, Velimir P. Stefanovi, Christos Tzivanidis and Zoran M. Stamenkovi "Design, Simulation ,and Optimiztion Of A Solar Dish Collector with spiral coil absorber ", , Nis, Serbia, thermal SCIENCE, Vol. 20, No. 4, pp. 1387-1397 1387,2016  12. Flávia V. Barbosa, João L. Afonso, Filipe B. Rodrigues, and José C. F. Teixeir," Development of a solar concentrator with tracking system", University of Minho,Guimarães, 4800-058, Portugal2016  13. O. López, A. Arenas, and A. Baños"Convective Heat Loss Analysis of a Cavity Receiver for a Solar Concentrator" International Conference on Renewable Energies and Power Quality (ICREPQ’17)Malaga (Spain), 4th to 6th April, 2017 ,ISSN 2172-038 X, No.15 April 2017 RE&PQJ, Vol.1, No.15, April 2017  14. D.R.Rajendran,E.GanapathySundaram,P.Jawahar "Experimental Studies on the Thermal Performance of a Parabolic Dish Solar Receiver with the Heat Transfer Fluids Sic water Nano Fluid and Water", Journal of Thermal Science Vol.26,  15. Muhammad Shoaib, Muhammad , Jameel Kabbir Ali ,Muhammad Usman1, Abdul Hannan " Analysis of thermal performance of parabolic dish collectors having different reflective" ,NFC institute of engineering &fertilizer research ,2018 .  16. Sasa PAVLOVIC, Evangelos BELLOS, Velimir STEFANOVIC ,Christos TZIVANIDIS " EXPERIMENTAL AND NUMERICAL INVESTIGATION OF A SOLAR DISH COLLECTOR WITH SPIRAL ABSORBER" A CTA TECHNICA CORVINIENSIS – Bulletin of Engineering Tome XI [2018] .   

A Simulation Model for Predicting the Performance of Solar Domestic Hot Water System

2012 ◽  
Vol 512-515 ◽  
pp. 230-233
Author(s):  
Le Minh Nhut ◽  
Youn Cheol Park
Keyword(s):  
Solar Collector ◽  
Storage Tank ◽  
Water System ◽  
Electricity Consumption ◽  
Hot Water ◽  
Initial Water ◽  
Heat Gain ◽  
Domestic Hot Water ◽  
Useful Heat Gain ◽  
Useful Heat

The article deals with the modeling and simulation aspects of the performance improvement of a solar domestic hot water system. A mathematical model of this system is carried out to predict its operating performance under specified weather conditions of Jeju Island, Korea. The optimum mass flow rate through collector based on the relationship between the useful heat gain of solar collector and the electricity consumption of solar pump is investigated. Besides, the effect of various parameters such as solar collector area, initial water temperature and volume of storage tank is analyzed. The result of the simulation shows that the optimum mass flow rate was determined at kg/s with the new coefficient . At this value, the amount of useful heat gain slightly decreased about 84.3 (Wh) corresponds to 0.16% but the amount of electricity consumption strongly decreased about 227.8 (Wh) corresponds to 48.8% compares with kg/s ( ) was proposed by . Furthermore, the system performance is affected strongly by the change of collector area, initial water temperature and volume of storage tank.

scholarly journals An Experimental Performance on Solar Photovoltaic Thermal Collector with Nanofluids for Sustainable Development

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Srinivasulu Gundala ◽  
M. Mahaboob Basha ◽  
V. Madhurima ◽  
N. Praveena ◽  
S. Venkatesh Kumar
Keyword(s):  
Sustainable Development ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Graphene Nanoplatelets ◽  
Solar Photovoltaic ◽  
Peak Period ◽  
Flow Rates ◽  
Experimental Performance ◽  
Electrical Efficiency ◽  
Water Based

In this article, the photovoltaic thermal collector (PVT) have designed and fabricated using nanoparticle nanofluid. The cause of this is to check out the effect of using water and water-based totally graphene nanoplatelets at an awareness of 0.05 wt% on the performance of PVT structures. Outdoor assessments have been performed at quantity along with the float prices of 0.5 L/min and 1.0 L/min for the aforementioned nanofluids, respectively, using water as a reference fluid. The results that have been analyzed from an active angle confirmed and determined that, graphene water nanofluid achieved higher in phrases of photovoltaic active conversion, than water that might generate the first-class thermal performance sooner or later of the peak period of sun radiation and high mobile temperature. The inclusion of water in the PVT collector increases average daily electrical efficiency by 7.8%, and 8.5%at flow rates of 0.5 LPM and 1.0 LPM, respectively. Furthermore, using water in the PVT collector increases average daily thermal efficiency by 24.9%, and 26.3%at flow rates of 0.5 LPM and 1.0 LPM, respectively.

Experimental Study on Thermal Efficiency of Parabolic Trough Collector (PTC) Using Al2O3/H2O Nanofluid

2015 ◽  
Vol 787 ◽  
pp. 192-196
Author(s):  
E. Siva Reddy ◽  
R. Meenakshi Reddy ◽  
K. Krishna Reddy
Keyword(s):  
Experimental Study ◽  
Solar Energy ◽  
Thermal Efficiency ◽  
Base Fluid ◽  
Concentration Ratio ◽  
Volume Fraction ◽  
Nano Particles ◽  
Parabolic Trough ◽  
Flow Rates ◽  
Parabolic Trough Collector

Dispersing small amounts of solid nano particles into base-fluid has a significant impact on the thermo-physical properties of the base-fluid. These properties are utilized for effective capture and transportation of solar energy. This paper attempts key idea for harvesting solar energy by using alumina nanofluid in concentrating parabolic trough collectors. An experimental study is carried out to investigate the performance of a parabolic trough collector using Al2O3-H2O based nanofluid. Results clearly indicate that at same ambient, inlet temperatures, flow rate, concentration ratio etc. hike in thermal efficiency is around 5-10 % compared to the conventional Parabolic Trough Collector (PTC). Further, the effect of various parameters such as concentration ratio, receiver length, fluid velocity, volume fraction of nano particles has been studied. The different flow rates employed in the experiment are 2 ml/s, 4 ml/s and 6 ml/s. Volumetric concentration of 0.02%, 0.04% and 0.06% has been studied in the experiment. Surfactants are not introduced to avoid bubble formation. Tracking mode of parabolic trough collector is manual. Results also reveal that Al2O3-H2O based nanofluid has higher efficiency at higher flow rates.

Sign in / Sign up

Export Citation Format

Share Document