scholarly journals Dual-mode multifunction filter realized with a single voltage differencing gain amplifier (VDGA)

2021 ◽  
Vol 41 (2) ◽  
Author(s):  
Worapong Tangsrirat ◽  
Tattaya Pukkalanun ◽  
Orapin Channumsin
Keyword(s):  
Current Mode ◽  
Angular Frequency ◽  
Cmos Process ◽  
Dual Mode ◽  
Biquad Filter ◽  
Multifunction Filter ◽  
Circuit Component ◽  
Simulation Results ◽  
Quality Factor Q ◽  
Circuit Configuration

This article presents the dual-mode multifunction biquad filter realized employing only a single voltage differencing gain amplifier (VDGA), one resistor and three capacitors. The proposed filterwith one input and three outputs can configure as voltage-mode or current-mode filter circuit with the appropriate input injection choice. It can also synthesis the three standard filter functions, which are highpass, bandpass, and lowpass responses without modifying the circuit configuration. Orthogonal adjustment between the natural angular frequency (o) and the quality factor (Q) of the filter is achieved. Detail analysis of non-ideal VDGA effects and circuit component sensitivity are included. The circuit principle is verified by means of simulation results with TSMC 0.35-m CMOS process parameters.

scholarly journals Single VDTA Based Dual Mode Single Input Multioutput Biquad Filter

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Rajeshwari Pandey ◽  
Neeta Pandey ◽  
Navin Singhal
Keyword(s):  
Current Mode ◽  
Angular Frequency ◽  
Cmos Process ◽  
Dual Mode ◽  
Biquad Filter ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
High Pass

This paper presents a dual mode, single input multioutput (SIMO) biquad filter configuration using single voltage differencing transconductance amplifier (VDTA), three capacitors, and a grounded resistor. The proposed topology can be used to synthesize low pass (LP), high pass (HP), and band pass (BP) filter functions. It can be configured as voltage mode (VM) or current mode (CM) structure with appropriate input excitation choice. The angular frequency (ω0) of the proposed structure can be controlled independently of quality factor (Q0). Workability of the proposed biquad configuration is demonstrated through PSPICE simulations using 0.18 μm TSMC CMOS process parameters.

scholarly journals Gm-Realization of Controlled-Gain Current Follower Transconductance Amplifier

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Worapong Tangsrirat
Keyword(s):  
Current Mode ◽  
Cmos Technology ◽  
Current Transfer ◽  
Biquad Filter ◽  
Transconductance Amplifier ◽  
Current Follower ◽  
Dc Bias ◽  
Simulation Results ◽  
Supply Voltages ◽  
A Current

This paper describes the conception of the current follower transconductance amplifier (CFTA) with electronically and linearly current tunable. The newly modified element is realized based on the use of transconductance cells (Gms) as core circuits. The advantage of this element is that the current transfer ratios (iz/ipandix/iz) can be tuned electronically and linearly by adjusting external DC bias currents. The circuit is designed and analyzed in 0.35 μm TSMC CMOS technology. Simulation results for the circuit with ±1.25 V supply voltages show that it consumes only 0.43 mw quiescent power with 70 MHz bandwidth. As an application example, a current-mode KHN biquad filter is designed and simulated.

Improved Electronically-Tunable Current-Mode Square-Root-Domain First-Order Multifunction Filter

2021 ◽  
pp. 2150190
Author(s):  
Manoj Kumar Jain
Keyword(s):  
Transient Response ◽  
Current Mode ◽  
Square Root ◽  
Spice Simulation ◽  
First Order ◽  
Low Pass ◽  
Multifunction Filter ◽  
Simulation Results ◽  
Electronically Tunable ◽  
High Pass

Some time back, Kircay reported an electronically-tunable current-mode square-root-domain first-order filter capable of realizing low-pass (LP), high-pass (HP) and all-pass (AP) filter functions. When simulated in SPICE, Kircay’s circuit has been found to exhibit DC offsets in case of LP and AP responses and incorrect transient response in case of HP response. In this paper, an improved circuit overcoming these difficulties/deficiencies has been suggested and its workability of the improved circuit as well as its capability in meeting the intended objectives has been demonstrated by SPICE simulation results.

scholarly journals Transadmittance Type Universal Current-Mode Biquad Filter Using VDTAs

2014 ◽  
Vol 2014 ◽  
pp. 1-4 ◽  
Author(s):  
Dinesh Prasad ◽  
Mayank Srivastava ◽  
D. R. Bhaskar
Keyword(s):  
Process Parameters ◽  
Current Mode ◽  
Angular Frequency ◽  
Pspice Simulations ◽  
Biquad Filter ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
Transconductance Amplifiers ◽  
High Pass

A new resistorless single-input-multi-output (SIMO) universal transadmittance (TA) type filter employing two voltage differencing transconductance amplifiers (VDTA) and two grounded capacitors is proposed. The proposed topology realizes simultaneously low pass (LP), high pass (HP), and band pass (BP) filter functions. Band rejects (BR) and all pass (AP) filters are also realizable through appropriate connections of currents. The proposed configuration also offers independent control of natural angular frequency (ω0) and bandwidth (BW) and low active and passive sensitivities. The workability of proposed configuration has been demonstrated through PSPICE simulations with TSMC CMOS 0.18 μm process parameters.

Single Inductor Bipolar Outputs DC-DC Converter with Current Mode Control Circuit

2013 ◽  
Vol 534 ◽  
pp. 220-226 ◽  
Author(s):  
Nobukazu Takai ◽  
Takashi Okada ◽  
Kenji Takahashi ◽  
Hajime Yokoo ◽  
Shunsuke Miwa ◽  
...  
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Process ◽  
Power Supply Voltage ◽  
Negative Power ◽  
Current Mode Control ◽  
Mode Control ◽  
Digital Still Camera ◽  
Simulation Results

Mobile equipment such as organic-EL display, digital still camera and so on re-quire both positive and negative power supply voltage to obtain high quality. Single InductorMultiple-Output (SIMO) DC-DC converter can provide a pair of positive and negative outputvoltages with only one external inductor. This paper describes SIMO DC-DC Converter usingproposed current-mode control (CMC) circuit. The proposed CMC circuit realizes high responsespeed for the change of load current. Spectre simulations with 0.18m CMOS process parameterare performed to verify the validity of the proposed converter. The simulation results indicatethat the proposed converter has higher response time compared with conventional converter.

scholarly journals High-Input Impedance Voltage-Mode Multifunction Filter

2021 ◽  
Vol 11 (1) ◽  
pp. 387
Author(s):  
San-Fu Wang ◽  
Hua-Pin Chen ◽  
Yitsen Ku ◽  
Yi-Fang Li
Keyword(s):  
Input Impedance ◽  
Angular Frequency ◽  
High Input ◽  
High Input Impedance ◽  
Current Feedback ◽  
Circuit Performance ◽  
Voltage Mode ◽  
Biquad Filter ◽  
Low Pass ◽  
Multifunction Filter

This paper proposes a high-input impedance voltage-mode (VM) multifunction biquad filter which employs three current-feedback amplifiers (CFAs), three resistors, and two grounded capacitors. The proposed VM multifunction biquad filter has single-input and triple-output and can realize non-inverting low-pass (NLP), inverting band-pass (IBP), and non-inverting band-stop (NBS) voltage responses at the same time without increasing component selection. The proposed VM multifunction biquad filter enjoys the orthogonal tunability of angular frequency and quality factor and also provides the advantage of using only two grounded capacitors, high-input impedance and low active/passive sensitivity. The performance of the proposed VM multifunction biquad filter is verified through its hardware implementation and OrCAD PSpice simulation based on AD844-type CFAs. The circuit analysis, sensitivity analysis, and NLP, IBP, and NBS voltage responses are also shown in this paper. The paper presents a method to effectively reduce the active and passive components, maintain good circuit performance, and reduce circuit costs.

scholarly journals Three-Input Single-Output Electronically Controllable Dual-Mode Universal Biquad Filter Using DO-CCCIIs

2007 ◽  
Vol 2007 ◽  
pp. 1-6 ◽  
Author(s):  
M. Siripruchyanun ◽  
W. Jaikla
Keyword(s):  
Integrated Circuit ◽  
Current Mode ◽  
Dual Mode ◽  
Voltage Mode ◽  
Single Output ◽  
Biquad Filter ◽  
Biquadratic Filter ◽  
Circuit Description ◽  
Electronically Controllable ◽  
The Given

This article presents a dual-mode (voltage-mode and current-mode) universal biquadratic filter performing completely standard functions: lowpass, highpass, bandpass, band-reject, and allpass functions, based on plus-type dual-output second-generation, current controlled, current conveyor (DO-CCCII+). The features of the circuit are that the bandwidth and natural frequency can be tuned electronically via the input bias currents: the circuit description is very simple, consisting of merely 2 DO-CCCIIs and 2 capacitors: the circuit can provide either the voltage-mode or current-mode filter without changing circuit topology. Additionally, each function response can be selected by suitably selecting input signals with digital method. Without any external resistors, the proposed circuit is very suitable to further develop into an integrated circuit. The PSPICE simulation results are depicted. The given results agree well with the theoretical anticipation. The maximum power consumption is approximately 1.81 mW at±1.5 V supply voltages.

Mixed-Mode Universal Biquad Filter Using OTAs

2019 ◽  
Vol 29 (10) ◽  
pp. 2050162 ◽  
Author(s):  
Data R. Bhaskar ◽  
Ajishek Raj ◽  
Pragati Kumar
Keyword(s):  
Integrated Circuit ◽  
Mixed Mode ◽  
Current Mode ◽  
Cmos Process ◽  
Design Environment ◽  
Single Output ◽  
Biquad Filter ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable

This paper introduces an electronically tunable mixed-mode universal biquad filter configuration employing four single output operational transconductance amplifiers (OTAs), one dual output OTA and two grounded capacitors (GCs) (ideal for integrated circuit implementation and absorbing shunt parasitic capacitances). The presented structure can realize all second-order filter functions, namely, low pass (LP), high pass (HP), band pass (BP), band reject (BR) and all pass (AP) responses in voltage mode (VM), current mode (CM), transresistance mode (TRM) and transconductance mode (TCM) using appropriate selection(s) of input signals. The cut-off frequency ([Formula: see text] and bandwidth (BW) of the realized filters can be tuned orthogonally through the transconductance (by varying the bias currents) of the OTAs. The proposed biquad configuration enjoys low active and passive sensitivities. The workability of this multifunctional biquad filter topology has been confirmed through simulations using MATLAB and Analog Design Environment (ADE) spectre tool provided by Cadence Virtuoso, using 0.18[Formula: see text][Formula: see text]m CMOS process parameter. The post-layout simulations have also been carried out to validate the theory.

scholarly journals Cascadable Current-Mode First-Order and Second-Order Multifunction Filters Employing Grounded Capacitors

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Jiun-Wei Horng ◽  
Chun-Li Hou ◽  
Ching-Yao Tseng ◽  
Ryan Chang ◽  
Dun-Yih Yang
Keyword(s):  
Theoretical Analysis ◽  
Second Generation ◽  
Current Mode ◽  
Bandpass Filters ◽  
Second Order ◽  
Current Conveyors ◽  
First Order ◽  
Simulation Results ◽  
Circuit Configuration ◽  
High Output

A configuration for realizing low input and high output impedances current-mode multifunction filters using multiple output second-generation current conveyors (MOCCIIs) is presented. From the proposed circuit configuration, first-order allpass, highpass, lowpass and second-order allpass, notch, bandpass filters can be obtained. The simulation results confirm the theoretical analysis.

scholarly journals A Novel Cross-Latch Shift Register Scheme for Low Power Applications

2020 ◽  
Vol 11 (1) ◽  
pp. 129
Author(s):  
Po-Yu Kuo ◽  
Ming-Hwa Sheu ◽  
Chang-Ming Tsai ◽  
Ming-Yan Tsai ◽  
Jin-Fa Lin
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Electrical Power ◽  
Average Power ◽  
Leakage Power ◽  
Shift Register ◽  
Cmos Process ◽  
Average Power Consumption ◽  
Simulation Results ◽  
Layout Area

The conventional shift register consists of master and slave (MS) latches with each latch receiving the data from the previous stage. Therefore, the same data are stored in two latches separately. It leads to consuming more electrical power and occupying more layout area, which is not satisfactory to most circuit designers. To solve this issue, a novel cross-latch shift register (CLSR) scheme is proposed. It significantly reduced the number of transistors needed for a 256-bit shifter register by 48.33% as compared with the conventional MS latch design. To further verify its functions, this CLSR was implemented by using TSMC 40 nm CMOS process standard technology. The simulation results reveal that the proposed CLSR reduced the average power consumption by 36%, cut the leakage power by 60.53%, and eliminated layout area by 34.76% at a supply voltage of 0.9 V with an operating frequency of 250 MHz, as compared with the MS latch.

Sign in / Sign up

Export Citation Format

Share Document