scholarly journals Use of alternative fuels obtained from renewable sources in Brayton cycles

2013 ◽  
Vol 14 (2) ◽  
pp. 157-165
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Alcoholic Fermentation ◽  
Combined Cycle ◽  
Brayton Cycle ◽  
Renewable Sources ◽  
Turbine Performance ◽  
Total Variability ◽  
Points Of View

Analysis and simulation of the behaviour of gas turbines for power generation using different nonconventional fuels obtained from different renewable sources are presented. Three biomass-tobiofuel processes are considered: anaerobic digestion of biomass (biogas), biomass gasification (synthesis gas) and alcoholic fermentation of biomass and dehydration (bioethanol), each of them with two different biomass substrates (energy crops and municipal solid waste) as input. The gas turbine behaviour in a Brayton cycle is simulated both in an isolated operation and in combined cycle. The differences in gas turbine performance when fired with the considered biofuels compared to natural gas are studied from different points of view related with the current complex energetic context: energetic and exergetic efficiency of the simple/combined cycle and CO2 emissions. Two different tools have been used for the simulations, each one with a different approach: while PATITUG (own software) analyses the behaviour of a generic gas turbine allowing a total variability of parameters, GT-PRO (commercial software) is more rigid, albeit more precise in the prediction of real gas turbine behaviour. Different potentially interesting configurations and its thermodynamic parameters have been simulated in order to obtain the optimal range for all of them and its variation for each fuel.

Numerical and Experimental Investigation of Secondary Flows and Influence of Air System Design on Heavy-Duty Gas Turbine Performance

2012 ◽  
Author(s):  
Luca Bozzi ◽  
Enrico D’angelo
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Combined Cycle ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Heavy Duty ◽  
Turbine Performance ◽  
Air System ◽  
Secondary Air

High turn-down operating of heavy-duty gas turbines in modern Combined Cycle Plants requires a highly efficient secondary air system to ensure the proper supply of cooling and sealing air. Thus, accurate performance prediction of secondary flows in the complete range of operating conditions is crucial. The paper gives an overview of the secondary air system of Ansaldo F-class AEx4.3A gas turbines. Focus of the work is a procedure to calculate the cooling flows, which allows investigating both the interaction between cooled rows and additional secondary flows (sealing and leakage air) and the influence on gas turbine performance. The procedure is based on a fluid-network solver modelling the engine secondary air system. Parametric curves implemented into the network model give the consumption of cooling air of blades and vanes. Performances of blade cooling systems based on different cooling technology are presented. Variations of secondary air flows in function of load and/or ambient conditions are discussed and justified. The effect of secondary air reduction is investigated in details showing the relationship between the position, along the gas path, of the upgrade and the increasing of engine performance. In particular, a section of the paper describes the application of a consistent and straightforward technique, based on an exergy analysis, to estimate the effect of major modifications to the air system on overall engine performance. A set of models for the different factors of cooling loss is presented and sample calculations are used to illustrate the splitting and magnitude of losses. Field data, referred to AE64.3A gas turbine, are used to calibrate the correlation method and to enhance the structure of the lumped-parameters network models.

Conceptual Recovery of Exhaust Heat From a Conventional Gas Turbine by an Inter-Cooled Inverted Brayton Cycle

1999 ◽  
Author(s):  
Y. Tsujikawa ◽  
K. Ohtani ◽  
K. Kaneko ◽  
T. Watanabe ◽  
S. Fujii
Keyword(s):  
Gas Turbine ◽  
Heat Recovery ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Brayton Cycle ◽  
Turbine Performance ◽  
Exhaust Heat ◽  
Manufacturing Techniques ◽  
Industrial Gas Turbine ◽  
Made In

Improvements in industrial gas turbine performance have been made in last decade. Advances in the gas turbine technologies such as higher turbine inlet temperature, materials, and manufacturing techniques justify the development of new combined or cogeneration cycle schemes, with more advance heat recovery capabilities. This paper describes the performance analysis of an Inverted Brayton Heat Recovery (IBHR) cycle, which is combined with conventional gas turbine and worked as a bottoming cycle. The optimum characteristics have been calculated and it is shown that this cycle is superior to the conventional combined cycle and cogeneration systems in terms of thermal efficiency and specific output. The main feature of this new concept is that the inverted Brayton cycle with inter-cooling is introduced. Further, a new estimating function, “the emission coefficient of carbon-dioxide” has been successfully introduced to assess the environmental compatibility.

Part-Load Performance of Gas Turbines: Part II — Multi-Point Adaptation With Compressor Map Generation and GA Optimization

2012 ◽  
Author(s):  
E. Tsoutsanis ◽  
Y. G. Li ◽  
P. Pilidis ◽  
M. Newby
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Performance Model ◽  
Part Load ◽  
Design Performance ◽  
Turbine Performance ◽  
Map Generation ◽  
Compressor Map ◽  
Performance Adaptation

Accurate gas turbine performance simulation is a vital aid to the operational and maintenance strategy of thermal plants having gas turbines as their prime mover. Prediction of the part load performance of a gas turbine depends on the quality of the engine’s component maps. Taking into consideration that compressor maps are proprietary information of the manufacturers, several methods have been developed to encounter the above limitation by scaling and adapting component maps. This part of the paper presents a new off-design performance adaptation approach with the use of a novel compressor map generation method and Genetic Algorithms (GA) optimization. A set of coefficients controlling a generic compressor performance map analytically is used in the optimization process for the adaptation of the gas turbine performance model to match available engine test data. The developed method has been tested with off-design performance simulations and applied to a GE LM2500+ aeroderivative gas turbine operating in Manx Electricity Authority’s combined cycle power plant in the Isle of Man. It has been also compared with an earlier off-design performance adaptation approach, and shown some advantages in the performance adaptation.

Effects of Inlet Fogging and Wet Compression on Gas Turbine Performance

2006 ◽  
Author(s):  
Sepehr Sanaye ◽  
Hossein Rezazadeh ◽  
Mehrdad Aghazeynali ◽  
Mehrdad Samadi ◽  
Daryoush Mehranian ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Water Droplets ◽  
Turbine Performance ◽  
Compressor Inlet ◽  
Wet Compression ◽  
Inlet Duct

Inlet fogging has been noticed widely in recent years as a method of gas turbine air inlet cooling for increasing the power output of gas turbines and combined cycle power plants. To study the effects of inlet fogging on gas turbine performance, in the first step, the evaporation of water droplets in the compressor inlet duct was modeled, and at the end of the inlet duct, the diameter of water droplets were estimated. The results of this process were compared with the results of FLUENT software. In the second step, the droplets which were not evaporated in compressor inlet duct were studied during wet compression in the compressor and the reduction in compressor discharge air temperature was predicted. Finally, the effects of both evaporative cooling in inlet duct, and wet compression in compressor, on the power output, and turbine exhaust temperature of a gas turbine with turbine blade cooling were investigated. These results for various amounts of air bleeding, without and with inlet fogging in the range of (0–2%) overspray are reported.

Modern opportunities for preparation of ultra-pure water for feeding high-performance boiler plants

2020 ◽  
pp. 74-84
Author(s):  
A.A. Filimonova ◽  
◽  
N.D. Chichirova ◽  
A.A. Chichirov ◽  
A.A. Batalova ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Pure Water ◽  
Combined Cycle ◽  
Feed Water ◽  
Operational Characteristics ◽  
Treatment Equipment

The article provides an overview of modern high-performance combined-cycle plants and gas turbine plants with waste heat boilers. The forecast for the introduction of gas turbine equipment at TPPs in the world and in Russia is presented. The classification of gas turbines according to the degree of energy efficiency and operational characteristics is given. Waste heat boilers are characterized in terms of design and associated performance and efficiency. To achieve high operating parameters of gas turbine and boiler equipment, it is necessary to use, among other things, modern water treatment equipment. The article discusses modern effective technologies, the leading place among which is occupied by membrane, and especially baromembrane methods of preparing feed water-waste heat boilers. At the same time, the ion exchange technology remains one of the most demanded at TPPs in the Russian Federation.

Evolution of Gas Turbine Intake Air Filtration in a 420 MW Cogeneration Plant

2014 ◽  
Author(s):  
Steve Ingistov ◽  
Michael Milos ◽  
Rakesh K. Bhargava
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Economic Benefits ◽  
Cogeneration Plant ◽  
Air Filtration ◽  
Air Filter ◽  
Filter System ◽  
Turbine Performance ◽  
Filtration System ◽  
Operational Data

A suitable inlet air filter system is required for a gas turbine, depending on installation site and its environmental conditions, to minimize contaminants entering the compressor section in order to maintain gas turbine performance. This paper describes evolution of inlet air filter systems utilized at the 420 MW Watson Cogeneration Plant consisting of four GE 7EA gas turbines since commissioning of the plant in November 1987. Changes to the inlet air filtration system became necessary due to system limitations, a desire to reduce operational and maintenance costs, and enhance overall plant performance. Based on approximately 2 years of operational data with the latest filtration system combined with other operational experiences of more than 25 years, it is shown that implementation of the high efficiency particulate air filter system provides reduced number of crank washes, gas turbine performance improvement and significant economic benefits compared to the traditional synthetic media type filters. Reasons for improved gas turbine performance and associated economic benefits, observed via actual operational data, with use of the latest filter system are discussed in this paper.

scholarly journals Powering Ahead

2011 ◽  
Vol 133 (05) ◽  
pp. 30-33 ◽  
Author(s):  
Lee S. Langston
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Nuclear Power ◽  
Electrical Power ◽  
The United States ◽  
Combined Cycle ◽  
Electrical Power System ◽  
Efficient Technology ◽  
The Military

This article explores the increasing use of natural gas in different turbine industries and in turn creating an efficient electrical system. All indications are that the aviation market will be good for gas turbine production as airlines and the military replace old equipment and expanding economies such as China and India increase their air travel. Gas turbines now account for some 22% of the electricity produced in the United States and 46% of the electricity generated in the United Kingdom. In spite of this market share, electrical power gas turbines have kept a much lower profile than competing technologies, such as coal-fired thermal plants and nuclear power. Gas turbines are also the primary device behind the modern combined power plant, about the most fuel-efficient technology we have. Mitsubishi Heavy Industries is developing a new J series gas turbine for the combined cycle power plant market that could achieve thermal efficiencies of 61%. The researchers believe that if wind turbines and gas turbines team up, they can create a cleaner, more efficient electrical power system.

Performance Analysis of a Combined Cycle Power Plant Through Exergetic and Environmental Indices

2017 ◽  
Author(s):  
Edgar Vicente Torres González ◽  
Raúl Lugo Leyte ◽  
Martín Salazar Pereyra ◽  
Helen Denise Lugo Méndez ◽  
Miguel Toledo Velázquez ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Environmental Indices ◽  
Combined Cycle Power Plant ◽  
Combustion Gases ◽  
Combined Cycle Plant ◽  
Exergetic Analysis ◽  
Gas Turbine Power Plant

In this paper is carried out a comparison between a gas turbine power plant and a combined cycle power plant through exergetic and environmental indices in order to determine performance and sustainability aspects of a gas turbine and combined cycle plant. First of all, an exergetic analysis of the gas turbine and the combined is carried out then the exergetic and environmental indices are calculated for the gas turbine (case A) and the combined cycle (case B). The exergetic indices are exergetic efficiency, waste exergy ratio, exergy destruction factor, recoverable exergy ratio, environmental effect factor and exergetic sustainability. Besides, the environmental indices are global warming, smog formation and acid rain indices. In the case A, the two gas turbines generate 278.4 MW; whereas 415.19 MW of electricity power is generated by the combined cycle (case B). The results show that exergetic sustainability index for cases A and B are 0.02888 and 0.1058 respectively. The steam turbine cycle improves the overall efficiency, as well as, the reviewed exergetic indexes. Besides, the environmental indices of the gas turbines (case A) are lower than the combined cycle environmental indices (case B), since the combustion gases are only generated in the combustion chamber.

Performance Improvement Program for Kawasaki Gas Turbine

2017 ◽  
Author(s):  
Tomoki Taniguchi ◽  
Ryoji Tamai ◽  
Yoshihiko Muto ◽  
Satoshi Takami ◽  
Ryozo Tanaka ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermal Performance ◽  
Film Cooling ◽  
Gas Turbines ◽  
Large Scale ◽  
New Technologies ◽  
Design Procedure ◽  
Product Line ◽  
Combined Cycle ◽  
Improvement Program

Kawasaki Heavy Industries, Ltd (KHI) has started a comprehensive program to further improve performance and availability of existing Kawasaki gas turbines. In the program, one of the Kawasaki’s existing gas turbine was selected from the broad product line and various kinds of technology were investigated and adopted to further improve its thermal performance and availability. The new technologies involve novel film cooling of turbine nozzles, advanced and large-scale numerical simulations, new thermal barrier coating. The thermal performance target is combined cycle efficiency of 51.6% and the target ramp rate is 20% load per minute. The program started in 2015 and engine testing has just started. In this paper, details of the program are described, focusing on design procedure.

Marine Gas Turbine Performance Model for More Electric Ships

2011 ◽  
Author(s):  
George M. Koutsothanasis ◽  
Anestis I. Kalfas ◽  
Georgios Doulgeris
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Diesel Engines ◽  
Gas Turbines ◽  
Electric Propulsion ◽  
Operating Conditions ◽  
Prime Mover ◽  
Creep Life ◽  
Hull Fouling ◽  
Turbine Performance

This paper presents the benefits of the more electric vessels powered by hybrid engines and investigates the suitability of a particular prime-mover for a specific ship type using a simulation environment which can approach the actual operating conditions. The performance of a mega yacht (70m), powered by two 4.5MW recuperated gas turbines is examined in different voyage scenarios. The analysis is accomplished for a variety of weather and hull fouling conditions using a marine gas turbine performance software which is constituted by six modules based on analytical methods. In the present study, the marine simulation model is used to predict the fuel consumption and emission levels for various conditions of sea state, ambient and sea temperatures and hull fouling profiles. In addition, using the aforementioned parameters, the variation of engine and propeller efficiency can be estimated. Finally, the software is coupled to a creep life prediction tool, able to calculate the consumption of creep life of the high pressure turbine blading for the predefined missions. The results of the performance analysis show that a mega yacht powered by gas turbines can have comparable fuel consumption with the same vessel powered by high speed Diesel engines in the range of 10MW. In such Integrated Full Electric Propulsion (IFEP) environment the gas turbine provides a comprehensive candidate as a prime mover, mainly due to its compactness being highly valued in such application and its eco-friendly operation. The simulation of different voyage cases shows that cleaning the hull of the vessel, the fuel consumption reduces up to 16%. The benefit of the clean hull becomes even greater when adverse weather condition is considered. Additionally, the specific mega yacht when powered by two 4.2MW Diesel engines has a cruising speed of 15 knots with an average fuel consumption of 10.5 [tonne/day]. The same ship powered by two 4.5MW gas turbines has a cruising speed of 22 knots which means that a journey can be completed 31.8% faster, which reduces impressively the total steaming time. However the gas turbine powered yacht consumes 9 [tonne/day] more fuel. Considering the above, Gas Turbine looks to be the only solution which fulfills the next generation sophisticated high powered ship engine requirements.

Sign in / Sign up

Export Citation Format

Share Document