scholarly journals Critical Evaluation for Grading and Fineness Modulus of Concrete Sands used in Sulaymaniyah City-Iraq

2021 ◽  
Vol 27 (10) ◽  
pp. 34-49
Author(s):  
Muhammad Arf Muhammad ◽  
Bilal K. Mohammed ◽  
Faris R. Ahmed ◽  
Bayan S. Al Numan
Keyword(s):  
Critical Evaluation ◽  
Sieve Analysis ◽  
Fine Aggregate ◽  
Size Distributions ◽  
Test Results ◽  
Particle Size Distributions ◽  
Fine Aggregates ◽  
Blending Method ◽  
Field Samples ◽  
Fineness Modulus

Fine aggregates used for concrete works in Sulaymaniyah city frequently fail to meet the standard requirements for gradation and fineness modulus in cement concrete. This paper aims to critically evaluate gradation, fineness modulus, and clay contents of various natural sands produced and used for concrete work in the region.  Sixteen field sand samples were collected from various sites in Darbandikhan (5 samples), Qalat Dizah (5 samples), Koysinjaq (5 samples), and Piramagroon (1 sample) confirming to ASTM D75. The field samples were parted into test specimens based on ASTM C702. Then, sieve analysis was carried out on the oven-dry test specimens in compliance with ASTM C136. The test results of fine aggregates were compared with American, British, and Iraqi specification standards using ASTM C33, BS 882, and IQS No. 45. It was revealed that only three sands satisfy the ASTM gradation limits while others do not comply and are on the coarser side. Also, eight samples meet the requirements recommended by BS 882, whereas five samples meet limits by IQS No. 45. It was found that only three sands have the fineness modulus within the ranges recommended by ACI 211.1 and ACI 211.4, while the others have high values. Furthermore, it was found that all sands include an allowable amount of finer particles passing sieve size 0.075 mm. In order to improve particle size distributions, it is recommended to use the blending method to obtain a suitable fine aggregate from two or more failed sands.

scholarly journals Ultrafine portland cement performance

2018 ◽  
Vol 68 (330) ◽  
pp. 157 ◽  
Author(s):  
C. Argiz ◽  
E. Reyes ◽  
A. Moragues
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Portland Cement ◽  
Silica Fume ◽  
Structure Refinement ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Blending Method ◽  
Cement Based Materials ◽  
Ultrafine Cement

By mixing several binder materials and additions with different degrees of fineness, the packing density of the final product may be improved. In this work, ultrafine cement and silica fume mixes were studied to optimize the properties of cement-based materials. This research was performed in mortars made of two types of cement (ultrafine Portland cement and common Portland cement) and two types of silica fume with different particle-size distributions. Two Portland cement replacement ratios of 4% and 10% of silica fume were selected and added by means of a mechanical blending method. The results revealed that the effect of the finer silica fume mixed with the coarse cement enhances the mechanical properties and pore structure refinement at a later age. This improvement is somewhat lower in the case of ultrafine cement with silica fume.

scholarly journals The Use of Sheet Glass Powder as Fine Aggregate Replacement in Concrete

2010 ◽  
Vol 4 (1) ◽  
pp. 65-71 ◽  
Author(s):  
M. Mageswari ◽  
Dr. B. Vidivelli
Keyword(s):  
Sheet Glass ◽  
Glass Powder ◽  
Fine Aggregate ◽  
Test Results ◽  
Natural Sand ◽  
Aggregate Concrete ◽  
Fine Aggregates ◽  
Interesting Possibility ◽  
Compact State ◽  
Conservation Of Natural Resources

Sheet glass powder (SGP) used in concrete making leads to greener environment. In shops, near by Chidambaram many sheet glass cuttings go to waste, which are not recycled at present and usually delivered to landfills for disposal. Using SGP in concrete is an interesting possibility for economy on waste disposal sites and conservation of natural resources. This paper examines the possibility of using SGP as a replacement in fine aggregate for a new concrete. Natural sand was partially replaced (10%, 20%, 30%, 40% and 50%) with SGP. Compressive strength, Tensile strength (cubes and cylinders) and Flexural strength up to 180 days of age were compared with those of concrete made with natural fine aggregates. Fineness modulus, specific gravity, moisture content, water absorption, bulk density, %voids, % porosity (loose and compact) state for sand (S) and SDA were also studied. The test results indicate that it is possible to manufacture concrete containing Sheet glass powder (SGP) with characteristics similar to those of natural sand aggregate concrete provided that the percentage of SGP as fine aggregate is limited to 10-20%, respectively.

Measuring Bulk-Specific Gravity of Fine Aggregates: Development of New Test Method

2000 ◽  
Vol 1721 (1) ◽  
pp. 81-90 ◽  
Author(s):  
Prithvi S. Kandhal ◽  
Rajib B. Mallick ◽  
Mike Huner
Keyword(s):  
Specific Gravity ◽  
Asphalt Binder ◽  
Test Method ◽  
Fine Aggregate ◽  
Test Results ◽  
Rotating Drum ◽  
Current Test ◽  
Fine Aggregates ◽  
Repeatability And Reproducibility ◽  
Prototype Device

Bulk specific gravity of the fine aggregate is used in hot-mix asphalt volumetric-mix design (including Superpave) to determine the amount of asphalt binder absorbed by the aggregate and the percentage of voids in the mineral aggregate. The current test method (AASHTO T84) uses a cone method to establish the saturated surface dry (SSD) condition of the sample, which is necessary to conduct the test. This method does not work satisfactorily for fine aggregates that are very angular and have rough surface texture and, therefore, do not slump readily when in SSD condition. A research project was undertaken to develop automated equipment and a method of establishing the SSD condition of the fine aggregate. The wet sample of the fine aggregate is placed in a rotating drum and subjected to a steady flow of warm air. The temperature gradient of the incoming and outgoing air and the relative humidity of the outgoing air are monitored to establish the SSD condition. Two prototype devices were constructed. The test results obtained with the second prototype device are encouraging and are reported. Further improvements to be made to the second prototype device to improve the repeatability and reproducibility of the test have been identified.

Laboratory Investigate of the Effect of Fine Aggregates on Asphalt Mixture Materials

2011 ◽  
Vol 225-226 ◽  
pp. 577-580
Author(s):  
Yong Ye ◽  
Yi Zhou Cai
Keyword(s):  
Compressive Strength ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Fine Aggregate ◽  
Test Results ◽  
Creep Tests ◽  
Aggregate Gradation ◽  
Static Creep ◽  
Fine Aggregates

The objective of this study is to investigate and evaluate the effect of fine aggregates (aggregate size smaller than or equal to 2.36 mm) on the compressive strength and creep behavior of asphalt mixtures. The variables that are considered in the study include the sizes and gradations of fine aggregate. A kind of standant aggregate gradation and four kinds of reduced aggregate gradation mixture specimens are used. Uniaxial compression and static creep tests were realized at different loading conditions. The test results showed that the different fine aggregate sizes do not result in significant differences in compressive strength and creep values using the same percentage of fine aggregates (38.4%). Only the different gradations showed a little differences for mixtures made with different gradations but same aggregate size (between 2.36 and 1.18 mm).

scholarly journals Limbah Beton Sebagai Material Agregat Halus Terhadap Kuat Tekan Karakteristik

2019 ◽  
Vol 6 (2) ◽  
pp. 145
Author(s):  
Budiman Budiman
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Building Construction ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Fine Aggregates ◽  
Fineness Modulus

Concrete waste from building construction can cause problems for the environment [1]. The use of fine aggregates from concrete waste can be a solution. The purpose of this study is to determine the value of aggregate characteristics and the value of concrete compressive strength from the utilization of concrete waste as substitution fine aggregate use the DOE (department of environment) method and referring to standards SNI. This study used 50% and 60% waste mortal substitution on sand. The results showed that the characteristics of fine aggregate and coarse aggregate met the characteristic requirements for fineness modulus sand of 2.65 (Zone 2) while the aggregate was roughly 6.44 (Zone 3). The value of compressive strength with 50% and 60% concrete waste substitution each obtained the value of characteristic compressive strength of 57.24 kg / cm² and 101.03 kg / cm². The value of using mortar waste as fine aggregate substitution gives a positive value to the quality of concrete. This is evidenced increase in the value of 14.89% in concrete waste substitution 60%.

scholarly journals Kajian Pengaruh Variasi Material Terhadap Kuat Tekan Beton

2018 ◽  
Vol 3 (1) ◽  
pp. 55
Author(s):  
Suhendra Suhendra
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Coarse Aggregates ◽  
Fine Aggregates ◽  
Laboratory Test Results

Aggregate quality is very influential on the strength of the resulting concrete. Both coarse and fine aggregates have various characteristics identified from laboratory test results. This study aims to examine the use of various aggregates for a quality of concrete. The coarse aggregate and the fine aggregate used are obtained from the nearest location to the work to be performed. The quality of the concrete reviewed is K-125, K-175 and K-225. The coarse aggregates used are 1-2 size (in cm), 2-3 size (in cm) crushed aggregate and coral. The fine aggregates used for each of the coarse aggregates are also different. The results showed that the coral aggregate did not meet the gradations of concrete aggregate. While the fine aggregate does not meet the gradation of concrete aggregate for the three types used. The concrete compressive strength test results show the use of coarse aggregates of 2-3 size of crushed and coarse aggregate of corals giving the average compressive strength value required for all planned concrete strength. While concrete using coarse aggregates of rocks of size 1-2 only meet the specified compressive strength, but does not meet the required compressive strength.Key words: Aggregates, concrete, compressive strength

scholarly journals The influence of fine aggregate combinations on particle size distribution, grading parameters, and compressive strength of sandcrete blocks

2006 ◽  
Vol 33 (10) ◽  
pp. 1271-1278 ◽  
Author(s):  
A Omoregie ◽  
O E Alutu
Keyword(s):  
Compressive Strength ◽  
Fine Aggregate ◽  
Uniformity Coefficient ◽  
Benin City ◽  
Fine Aggregates ◽  
Curvature Coefficient ◽  
Coefficient Of Uniformity ◽  
Combination Approach ◽  
Strength And Durability ◽  
Fineness Modulus

The current extensive use of low priced fine aggregate (sand) deposits in sandcrete block making in Nigeria is of concern because there appears to be a level of ignorance surrounding their existing properties and implications. To this end, silt contents and some grading parameters of the most commonly used fine aggregate deposits in parts of midwestern Nigeria (Benin City), the coefficient of uniformity (Cu), curvature coefficient (Cc), and the fineness modulus (Fm) were derived by laboratory experiments to ascertain these basic properties. In addition, the strength and durability properties of sandcrete blocks made from these sands were also established. It revealed that the low priced sands exhibited worse properties in comparison to the more expensive sand. As a way of improving the properties of these frequently used low priced sands, a combination approach was adopted that used the weaker and commonly used sands with those that are more expensive and less frequently used. Findings revealed that combining the two created significant improvement in compressive strength, durability, and grading parameters of low priced sands with only marginal impact on cost.Key words: fine aggregates, uniformity coefficient, curvature coefficient, fineness modulus, compressive strength, durability, silt contents, Nigeria.

scholarly journals Effect of Fine Aggregate Particle Characteristics on Mechanical Properties of Fly Ash-Based Geopolymer Mortar

Minerals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 897
Author(s):  
Heng Li ◽  
Pengpeng Gao ◽  
Fang Xu ◽  
Tao Sun ◽  
Yu Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Pass Rate ◽  
Fine Aggregate ◽  
X Ray Diffraction ◽  
River Sand ◽  
Fine Aggregates ◽  
Compressive And Flexural Strengths ◽  
Filling Coefficient ◽  
Fineness Modulus

This research aimed to investigate the effect of fine aggregate particles on mechanical properties of fly ash-based geopolymer mortar. In this work, seven kinds of river sand particles were designed based on different fine aggregate characteristics. The fineness modulus was adopted to quantitatively describe the gradation of sands. The fluidity, compressive, flexural, and tensile strengths of geopolymer mortar with different sand gradations were analyzed by laboratory tests. Furthermore, the composition and morphology of fly ash-based geopolymer mortar was analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The reasonable gradation range and filling effect of sand were obtained. The results show that fluidity and compressive and flexural strengths of geopolymer mortar both improve with the increase of the fineness modulus, while specific surface area and voidage are opposite. The tensile strength of mortar largely lies on the interface properties between the geopolymer binder and fine aggregates. When the pass rate of the key sieving size 1.18 mm is 75–95%, the pass rate of the key sieving size 0.15 mm is 15–25%, the fineness modulus is 2.2–2.6 and the appropriate filling coefficient of geopolymer paste is around 1.0–1.15, the comprehensive performance of geopolymer mortar is the best. This research paper could provide a basis for the design of geopolymer mortar based on fly ash, and it is of great significance for its popularization and application.

scholarly journals Comparison on the Properties of Various Alternative Materials for Replacing River Sand in Structural Elements

2018 ◽  
Vol 7 (1) ◽  
pp. 48-51
Author(s):  
Theivabharathi .
Keyword(s):  
Construction Industry ◽  
Large Scale ◽  
Copper Slag ◽  
Sieve Analysis ◽  
Fine Aggregate ◽  
Test Results ◽  
Structural Elements ◽  
River Sand ◽  
Alternative Materials ◽  
Different Sources

River sand is a non-renewable source of material which we have been utilizing it in construction for years. In this paper replacement of natural river sand by various by-products and waste materials obtained from different sources have been taken for the study to compare their properties with that of the river sand. The alternative materials considered for the study were M-sand, Eco sand, Copper slag, crushed glass, quarry dust, foundry sand, biomedical waste ash. Some of the materials have been already tested and the optimum percentage of usage in concrete has been determined. But the comparison of their properties with that of the river sand with 100% replacement have been carried out for the study in order to check their potential to act as fine aggregate in concrete or construction industry. The tests performed were sieve analysis, specific gravity, moisture contentand compressive strength of cement mortar cubes.The test results obtained would help us in projecting a newer dimension in use of these materials in structural elements too. If it’s proven successful, thenwe would be able to implement it in large scale which would help us to revolutionize the construction industry by economizing the construction cost and enabling us to conserve the natural resources.

Sign in / Sign up

Export Citation Format

Share Document