The impact of distortions of phase-shift keyed signals with gradual phase change in the receiver input circuits on the signal detection characteristics during the signal reception against the background of noise

2012 ◽  
Vol 55 (8) ◽  
pp. 360-367
Author(s):  
G. S. Nakhmanson ◽  
A. V. Suslin
Keyword(s):  
Phase Shift ◽  
Signal Detection ◽  
Phase Change ◽  
Gradual Phase ◽  
Detection Characteristics ◽  
The Impact ◽  
Receiver Input

scholarly journals Numerical Simulation of the Impact of the Heat Source Position on Melting of a Nano-Enhanced Phase Change Material

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1425
Author(s):  
Tarek Bouzennada ◽  
Farid Mechighel ◽  
Kaouther Ghachem ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Melting Rate ◽  
Heat Transfer Fluid ◽  
Commercial Code ◽  
Tube Position ◽  
The Impact ◽  
Change Material

A 2D-symmetric numerical study of a new design of Nano-Enhanced Phase change material (NEPCM)-filled enclosure is presented in this paper. The enclosure is equipped with an inner tube allowing the circulation of the heat transfer fluid (HTF); n-Octadecane is chosen as phase change material (PCM). Comsol-Multiphysics commercial code was used to solve the governing equations. This study has been performed to examine the heat distribution and melting rate under the influence of the inner-tube position and the concentration of the nanoparticles dispersed in the PCM. The inner tube was located at three different vertical positions and the nanoparticle concentration was varied from 0 to 0.06. The results revealed that both heat transfer/melting rates are improved when the inner tube is located at the bottom region of the enclosure and by increasing the concentration of the nanoparticles. The addition of the nanoparticles enhances the heat transfer due to the considerable increase in conductivity. On the other hand, by placing the tube in the bottom area of the enclosure, the liquid PCM gets a wider space, allowing the intensification of the natural convection.

Evaluation the effect of the ambient temperature on the liquid petroleum gas transportation pipeline

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Ammar Ali Abd ◽  
Samah Zaki Naji ◽  
Ching Thian Tye ◽  
Mohd Roslee Othman
Keyword(s):  
Energy Consumption ◽  
Greenhouse Gases ◽  
Ambient Temperature ◽  
Phase Change ◽  
Liquid State ◽  
Pump Energy ◽  
Compressible Liquid ◽  
Liquefied Petroleum Gas ◽  
Efficient Design ◽  
The Impact

Abstract Liquefied petroleum gas (LPG) plays a major role in worldwide energy consumption as a clean source of energy with low greenhouse gases emission. LPG transportation is exhibited through networks of pipelines, maritime, and tracks. LPG transmission using pipeline is environmentally friendly owing to the low greenhouse gases emission and low energy requirements. This work is a comprehensive evaluation of transportation petroleum gas in liquid state and compressible liquid state concerning LPG density, temperature and pressure, flow velocity, and pump energy consumption under the impact of different ambient temperatures. Inevitably, the pipeline surface exchanges heat between LPG and surrounding soil owing to the temperature difference and change in elevation. To prevent phase change, it is important to pay attention for several parameters such as ambient temperature, thermal conductivity of pipeline materials, soil type, and change in elevation for safe, reliable, and economic transportation. Transporting LPG at high pressure requests smaller pipeline size and consumes less energy for pumps due to its higher density. Also, LPG transportation under moderate or low pressure is more likely exposed to phase change, thus more thermal insulation and pressure boosting stations required to maintain the phase envelope. The models developed in this work aim to advance the existing knowledge and serve as a guide for efficient design by underling the importance of the mentioned parameters.

scholarly journals Latent Heat Thermal Storage of Nano-Enhanced Phase Change Material Filled by Copper Foam with Linear Porosity Variation in Vertical Direction

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1508
Author(s):  
Mohammad Ghalambaz ◽  
Mohammad Shahabadi ◽  
S. A. M Mehryan ◽  
Mikhail Sheremet ◽  
Obai Younis ◽  
...  
Keyword(s):  
Natural Convection ◽  
Phase Change ◽  
Phase Change Material ◽  
Metal Foam ◽  
Vertical Direction ◽  
Melting Time ◽  
Copper Foam ◽  
Average Porosity ◽  
The Impact ◽  
Change Material

The melting flow and heat transfer of copper-oxide coconut oil in thermal energy storage filled with a nonlinear copper metal foam are addressed. The porosity of the copper foam changes linearly from bottom to top. The phase change material (PCM) is filled into the metal foam pores, which form a composite PCM. The natural convection effect is also taken into account. The effect of average porosity; porosity distribution; pore size density; the inclination angle of enclosure; and nanoparticles’ concentration on the isotherms, melting maps, and the melting rate are investigated. The results show that the average porosity is the most important parameter on the melting behavior. The variation in porosity from 0.825 to 0.9 changes the melting time by about 116%. The natural convection flows are weak in the metal foam, and hence, the impact of each of the other parameters on the melting time is insignificant (less than 5%).

scholarly journals Speeding Up the Write Operation for Multi-Level Cell Phase Change Memory with Programmable Ramp-Down Current Pulses

Micromachines ◽  
2019 ◽  
Vol 10 (7) ◽  
pp. 461 ◽  
Author(s):  
Chenchen Xie ◽  
Xi Li ◽  
Houpeng Chen ◽  
Yang Li ◽  
Yuanguang Liu ◽  
...  
Keyword(s):  
Phase Change ◽  
Current Source ◽  
Phase Change Memory ◽  
Operation Time ◽  
Access Time ◽  
Fully Differential ◽  
Current Pulses ◽  
Multi Level ◽  
The Impact ◽  
Change Memory

Multi-level cell (MLC) phase change memory (PCM) can not only effectively multiply the memory capacity while maintaining the cell area, but also has infinite potential in the application of the artificial neural network. The write and verify scheme is usually adopted to reduce the impact of device-to-device variability at the expense of a greater operation time and more power consumption. This paper proposes a novel write operation for multi-level cell phase change memory: Programmable ramp-down current pulses are utilized to program the RESET initialized memory cells to the expected resistance levels. In addition, a fully differential read circuit with an optional reference current source is employed to complete the readout operation. Eventually, a 2-bit/cell phase change memory chip is presented with a more efficient write operation of a single current pulse and a read access time of 65 ns. Some experiments are implemented to demonstrate the resistance distribution and the drift.

scholarly journals Thermo-physical characteristics of building integrated phase change materials (PCM) and their applicability to energy efficient homes

2021 ◽  
Author(s):  
Omar Siddiqui
Keyword(s):  
Compressive Strength ◽  
Phase Change ◽  
Phase Change Materials ◽  
Energy Savings ◽  
Physical Characteristics ◽  
Comfort Level ◽  
Thermal Mass ◽  
Lower Phase ◽  
Physical Test ◽  
The Impact

The applicability of utilizing a variety of thermal mass including phase change materials with commonly used building materials is investigated through the use of simulations and physical testing. The thermal performance and occupant comfort potential of a novel solid-solid phase change material, known as Dal HSM, is compared and contrasted to commonly available forms of thermal mass. Detailed experimentation is conducted to successfully integrate Dal HSM with gypsum and concrete. The measurement of physical characteristics such as compressive strength and modulus of rupture is conducted to ensure that the PCM-composite compound retains the structural integrity to be utilized in a typical building. The use of thermal mass in the Toronto Net Zero house was found to contribute to energy savings of 10-15% when different types of thermal mass were used. The comfort level of the indoor occupants was also found to increase. The performance of Dal HSM was found to be comparable to a commercially available PCM known as Micronal in the heating mode. The cooling mode revealed that Dal HSM provided slightly lower energy savings when compared to Micronal due to a lower phase transition temperature and latent heat. The performance of physical test revealed a decrease in the compressive strength as the concentration of Dal HSM was increased in the PCM-gypsum specimens. Tests were also performed to analyze the impact of increasing the PCM concentration on the flexural strength of PCM-gypsum composite.

scholarly journals Impact of Crystalline Orientation on the Switching Field in Barium Titanate Using Piezoresponse Force Spectroscopy

2014 ◽  
Vol 1652 ◽  
Author(s):  
Nikhil K. Ponon ◽  
Daniel J. R. Appleby ◽  
Erhan Arac ◽  
Kelvin S. K. Kwa ◽  
Jonathan P. Goss ◽  
...  
Keyword(s):  
Electric Field ◽  
Phase Change ◽  
Crystal Orientation ◽  
Force Spectroscopy ◽  
Ferroelectric Domain ◽  
Switching Field ◽  
The Impact ◽  
Non Destructive ◽  
Domain Level

ABSTRACTUnderstanding crystal orientation at the ferroelectric domain level, using a non destructive technique, is crucial for the design and characterization of nano-scale devices. In this study, piezoresponse force spectroscopy (PFS) is used to identify ferroelectric domain orientation. The impact of crystal orientation on the switching field of ferroelectric BaTiO3 is also investigated at the domain level. The preferential domain orientations for BaTiO3 thin films prepared by pulsed laser deposition (PLD) in this study are [001], [101] and [111]. They have been mapped onto PFS spectra to show three corresponding switching fields of 460, 330 and 120 kV/cm respectively. In addition, the electric field at which the enhanced piezoresponse occurs was found to vary, due to a phase change. The polarization reversal occurs via a 2-step process (rotation and switching) for [101] and [111] orientations. The piezoresponse enhancement is absent for the [001] (pure switching) domains. The results demonstrate that an electric field induced phase change causes the [101] and [111] domains to reverse polarization at a lower field than the [001] domain.

Sign in / Sign up

Export Citation Format

Share Document