scholarly journals Comparative Study of Cleansing Action of Some Detergents Available in Nepalese Market

2021 ◽  
Vol 19 (2) ◽  
pp. 83-89
Author(s):  
Arvind Pathak ◽  
Pratima Khadka ◽  
Prabin Karki
Keyword(s):  
Surface Tension ◽  
Critical Micelle Concentration ◽  
Ground Water ◽  
Emulsion Stability ◽  
Tap Water ◽  
Hard Water ◽  
Stability Test ◽  
Distilled Water ◽  
Water Test ◽  
Emulsions Stability

Detergents commercially available in the Nepalese market were studied and several parameters such as surface tension, pH, critical micelle concentration, foaming stability test, hard water test, emulsions stability test were performed. Different medium such as ground water (G.W.), tap water (T.W.), distilled water (D.W.) and 5% ethanol in distilled water were selected for this study. The decrease in surface tension and critical micelle concentration (CMC) in ground water, tap water, distilled water and 5% ethanol in distilled water, ease of cleansing action of the detergents in this medium have been found of the following order: 5% ethanol in distilled water > distilled water (D.W.) > tap water (T.W.) > ground water (G.W.). Among the four detergents, the D1 have shown the least surface tension, CMC value, foam collapsing time, the weight of scum formed when treated with hard water. And maximum emulsion stability of the detergent D1 determines good quality detergent.

scholarly journals Micellization behaviour of sodium dodecyl sulphate in presence and absence of sodium sulphate and zinc sulphate in distilled water by surface tension measurement

BIBECHANA ◽  
2014 ◽  
Vol 11 ◽  
pp. 79-85 ◽  
Author(s):  
Kuber Limbu ◽  
Sujit Kumar Shah ◽  
Ajaya Bhattarai
Keyword(s):  
Surface Tension ◽  
Critical Micelle Concentration ◽  
Sodium Dodecyl Sulphate ◽  
Room Temperature ◽  
Zinc Sulphate ◽  
Sodium Dodecyl ◽  
Sodium Sulphate ◽  
Distilled Water ◽  
Surface Tension Measurement ◽  
Weight Method

The accurate measurements of surface tension of sodium dodecyl sulphate (SDS) in distilled water and in presence of 0.01M Na2SO4 and 0.01M ZnSO4 at room temperature were reported by drop weight method using a stalagmometer. The critical micelle concentration (cmc) of sodium dodecyl sulphate (SDS) in distilled water was obtained higher than in presence of Na2SO4 and ZnSO4. The decrease of cmc of sodium dodecyl sulphate in the presence of salts has been discussed. DOI: http://dx.doi.org/10.3126/bibechana.v11i0.10383 BIBECHANA 11(1) (2014) 79-85

Perbandingan Karakteristik Surfaktan Metil Ester Sulfonat dan Sodium Lauril Sulfonat sebagai Bahan Emulsifier

2016 ◽  
Vol 9 (2) ◽  
pp. 167-176
Author(s):  
Eldha Sampepana ◽  
Paluphy Eka Yustini ◽  
Aditya Rinaldi ◽  
Amiroh Amiroh
Keyword(s):  
Fatty Acids ◽  
Surface Tension ◽  
Methyl Ester ◽  
Interfacial Tension ◽  
Palm Oil ◽  
Emulsion Stability ◽  
Raw Material ◽  
Enzymatic Method

Surfactant which is used as raw emulsifier in an industry activity such as Sodium Lauryl Sulfonate is a raw material import, it is petroleum derivative which is not renewable and may cause pollution to the environment, because it is not degraded and are carcinogenic. The purpose of the research is to compare the characteristics of the Quaternary methyl ester sulfonat (MES) and Sodium Lauryl Sulfonat (SLS) as emulsifier. First, make the MES by filtering and eliminating fatty acids of palm oil, then process the MES with enzymatic method become methyl ester, then react it in sulfonation and metanolization process, and also neutralized with NaOH. Next, the MES experiment is compared with SLS and existing MES in the market. The results show that surfactants MES experiment has value hidrofil lipofil balance (HLB) interfacial tension and emulsion stability greater than MES in the market and SLS. And the surface tension of MES experiment is larger than MES in the market, but smaller compared to SLS.ABSTRAKSurfaktan yang digunakan sebagai bahan baku emulsifer dalam aktivitas suatu industri pada saat ini seperti Sodium Lauril Sulfonat  merupakan bahan baku import yang merupakan turunan dari minyak bumi, dengan sifat tidak dapat diperbaharui dan dapat menimbulkan pencemaran terhadap lingkungan karena tidak mudah terdegradasi serta bersifat karsinogenik. Metil ester sulfonat dari bahan minyak sawit merupakan surfaktan dengan sifat mudah terdegradasi yang perlu diketahui karakteristiknya. Penelitian bertujuan untuk membandingkan karakteristik surfaktan metil ester sulfonat (MES) dan Sodium Lauril Sulfonat (SLS) sebagai bahan emulsifier. Mula-mula dilakukan pembuatan MES dengan cara menyaring dan menghilangkan asam lemak minyak sawit terlebih dahulu, kemudian diolah menjadi metil ester secara enzimatis, lalu direaksikan secara sulfonasi dan metanolisis, serta dinetralkan dengan NaOH. Selanjutnya MES hasil percobaan dibandingkan dengan SLS dan MES yang ada dipasaran. Hasil penelitian menunjukkan bahwa surfaktan MES memiliki nilai hidrofil lipofil balance (HLB) tegangan antar muka dan stabilitas emulsi lebih besar apabila dibandingkan dengan MES di pasaran dan SLS, kecuali nilai stabilitas emulsi antara MES dan SLS sama. Dan tegangan permukaan MES hasil percobaan, lebih besar dibandingkan dengan MES dipasaran, dan lebih kecil dibandingkan dengan SLS. Kata kunci :   Metil  ester sulfonat, hidrofil lipofil balance, emulsifier, sodium lauril sulfonat , stabilitas emulsi 

Surface Activity Research of Cationic Gemini Surfactants

2013 ◽  
Vol 690-693 ◽  
pp. 2076-2080
Author(s):  
Zhen Zhong Fan ◽  
Lan Lan Li ◽  
Li Feng Zhang ◽  
Qing Wang Liu
Keyword(s):  
Surface Tension ◽  
Critical Micelle Concentration ◽  
Surface Activity ◽  
Surfactant Concentration ◽  
Gemini Surfactant ◽  
Gemini Surfactants ◽  
Ph Value ◽  
Inorganic Salts ◽  
Cationic Gemini Surfactant ◽  
Cationic Gemini Surfactants

Cationic Gemini surfactant concentration, the inorganic salts added and the pH value of surface tension obtained cationic gemini surfactant critical micelle concentration is 0.4mmol / L;by adding three kinds of inorganic salts NaCl, MgCl2, and Na2SO4 ,which Na2SO4 has the greatest impact on surface tension, followed by MgCl2.The surface minimum tension of the pH ranged from 9 to 11 , indicating that the surface activity of cationic gemini surfactants achieved the highest.

scholarly journals Effect of Ammonium on the Hydraulic Conductivity of Kaolin and Bentonite as Clay Liners

2020 ◽  
Vol 4 (2) ◽  
pp. 100-111
Author(s):  
Adebola Adebayo Adekunle ◽  
Igba Uvieoghene Tobit ◽  
Ogunrinola Oluwaseyi Gbemiga
Keyword(s):  
Hydraulic Conductivity ◽  
Ground Water ◽  
Tap Water ◽  
Bentonite Clay ◽  
Research Paper ◽  
Low Permeability ◽  
Main Function ◽  
Clay Liners ◽  
Landfill Liners ◽  
Different Sources

: Landfill liners are underlying materials with low permeability whose main function is to mitigate the infiltration of toxic contents into ground water lying beneath. Landfill liners are primarily made of bentonite clay. Bentonite has a very low hydraulic conductivity, that might not be readily accessible, unlike kaolin which is found to have a lower hydraulic conductivity compared to that of bentonite and can be extensively obtained from numerous different sources. Explored, for the purposes of the present research paper, were various ratios of bentonite and kaolin and their hydraulic conductivity, in particular ratios of 90:10 kaolin to bentonite, 80:20 kaolin to bentonite, 70:30 kaolin to bentonite, 60:40 kaolin to bentonite and 50:50 kaolin to bentonite in an effort to achieve an acceptable barrier suitable as a liner / where tap water and ammonium solution were used as permeants. It was concluded that the ratios not lower than 20% bentonite (80:20, 70:30, 60:40 and 50:50) all had their hydraulic conductivity value reduced compared to the 100% kaolin.

scholarly journals Insecticidal effects of insecticide, fungicide, complex fertilizer and wetting agent combinations depending on water hardness

2009 ◽  
Vol 24 (1) ◽  
pp. 43-49 ◽  
Author(s):  
Slavica Vukovic ◽  
Dusanka Indjic ◽  
Vojislava Bursic ◽  
Dragana Sunjka ◽  
Mila Grahovac
Keyword(s):  
Colorado Potato Beetle ◽  
Tap Water ◽  
Biological Effects ◽  
Water Hardness ◽  
Hard Water ◽  
Wetting Agent ◽  
Simultaneous Occurrence ◽  
Agricultural Practice ◽  
Potato Beetle ◽  
Novi Sad

Simultaneous occurrence of different harmful species in agricultural practice necessitates that different plant protection chemicals be applied at the same time (tank mix). Mix components differ in purpose, mode of action and/or formulation, while addition of no pesticide components (complex fertilizers, adjuvant and wetting agents) is widely practiced today. However, data concerning the effects of water quality used for preparation of working liquids on the biological effects of pesticides is still scarce. Therefore, the objective of this study was to determine insecticidal effects as depending on components used in mixes and water hardness. The effects of mixtures of thiametoxam (Actara 25-WG 0,07kg/ha) with azoxystrobin (Quadris 0.75 l/ha), mancozeb (Dithane M-70 2.5 kg/ha), a complex fertilizer (Mortonijc plus 3 kg/ha) and a wetting agent (Silwet L-77), depending on the components and water hardness (slightly hard (15.4 d?) - tap water from Novi Sad, and very hard (34.7 d?) - well water from Adica, a Novi Sad suburb), were determined in a bioassay based on adult mortality rate of the first generation of Colorado potato beetle (Leptinotarsa decemlineata Say). The mixtures were applied by a flooding method. The trial was set up to include four replications. Insecticidal effects were determined 24 h and 48 h after exposure. Thiametoxam effectiveness 24 h and 48 h after application in slightly hard water was 100% when the insecticide was applied alone and in double and triple mixes with the fungicides, complex fertilizer and wetting agent, showing no dependency on mix components. The tested adult population of Colorado potato beetle demonstrated high susceptibility to thiametoxam, while the other components had no impact in slightly hard water. In very hard water, 24 h after application, the insecticidal effect had the same level of significance to thiametoxam in double and triple mixes, with an exception of thiametoxam+mancozeb+Mortonijc plus and thiametoxam+mancozeb+wetting agent combinations, which showed significantly lower efficacy. After 48 h, substantially lower effectiveness, in comparison with the sole insecticide and other combinations, was only observed in thiametoksam+mancozeb+Mortonjic plus combination. Significantly lower efficacy of that combination is probably due to an incompatibility of the macozeb preparation and the complex fertilizer containing boron (B), which was evidenced only in very hard water.

scholarly journals Heavy metal levels in drinking water sources of Chingola District, Zambia

2020 ◽  
Author(s):  
Francis Hamwiinga ◽  
Chisala D. Meki ◽  
Patricia Mubita ◽  
Hikabasa Halwiindi
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Drinking Water ◽  
Ground Water ◽  
Water Samples ◽  
Tap Water ◽  
Water Sources ◽  
Wet Season ◽  
Drinking Water Sources ◽  
Metal Levels

Abstract Background: One of the factors impeding access to safe water is water pollution. Of particular concern is heavy metal contamination of water bodies. This study was aimed at determining the levels of heavy metals in drinking water sources of Chingola District of Zambia. Methods: A cross sectional study was employed. A total of 60 water samples were collected. Thirsty (30) samples were collected in the dry season in the month of October 2016 and another 30 in the wet season in the months of February and March, 2017. For each season 10 water samples were collected from each of the three water sources. i.e. Tap water, Urban ground water sources and Rural ground water sources. Heavy metal analysis was done using Atomic Absorption Spectrophotometer (AAS).Results: This study revealed that the concentrations of Iron, Manganese, Lead, Nickel and Arsenic were beyond maximum permissible levels in various water sources. Combined averages for both dry and wet seasons were as follows: Iron: 2.3, Copper: 0.63, Cobalt: 0.02, Manganese: 0.36, Lead: 0.04, Zinc:3.2, Nickel: 0.03, Arsenic: 0.05. Chromium and Cadmium were below detection limit in all water samples. The median concentrations of iron, arsenic, copper, manganese in drinking water from the Tap, rural and urban ground water sources were different, and this difference was statistically significant (p<0.05). The median concentrations of arsenic, nickel, manganese and cobalt were different between dry and wet season, and this difference was statistically significant (p<0.05).Conclusions: Sources of heavy metals in water seems to be both natural and from human activities. The concentration of heavy metals in different water sources in this study was found to be above the recommended levels. This calls for improvement in water monitoring to protect the health of the public. Therefore, there is need for continuous monitoring of heavy metals in drinking water sources by regulatory authorities.

Influence of Learning on Taste Preferences

1966 ◽  
Vol 19 (2) ◽  
pp. 445-446 ◽  
Author(s):  
Paul Thomas Young
Keyword(s):  
Tap Water ◽  
Taste Preferences ◽  
Distilled Water

Further discussion of the Schnorr and Brookshire study of the preference between distilled water and tap water, with comments and suggestions.

Survival of Two Bacterial Fish Pathogens (Aeromonas salmonicida and the Enteric Redmouth Bacterium) in Ozonated, Chlorinated, and Untreated Waters

1977 ◽  
Vol 34 (3) ◽  
pp. 429-432 ◽  
Author(s):  
Gary A. Wedemeyer ◽  
Nancy C. Nelson
Keyword(s):  
Lake Water ◽  
Contact Time ◽  
Free Water ◽  
Hard Water ◽  
Etiologic Agent ◽  
Aeromonas Salmonicida ◽  
Distilled Water ◽  
Fish Pathogens ◽  
Chlorine Residual ◽  
Lake Waters

Ozone and chlorine inactivation curves were determined in three water types at 20 °C for the destruction of the fish pathogens Aeromonas salmonicida, the etiologic agent of furunculosis, and the enteric redmouth bacterium (ERM). In phosphate-buffered distilled water, 0.01 mg/ℓ ozone inactivated 103 cells/ml of ERM and A. salmonicida in 1/2 and 10 min, respectively. Chlorine at this concentration had little effect on either pathogen and a residual of at least 0.05 mg/ℓ was needed to achieve a complete kill within a 10-min contact time. In soft lake water (30 mg/ℓ as CaCO3) a chlorine residual of 0.1 mg/ℓ rapidly [Formula: see text] inactivated A. salmonicida and ERM but in hard water (120 mg/ℓ) A. salmonicida was more resistant and 0.2 mg/ℓ chlorine was required. Ozonation of the two lake waters at 90 mg O3∙h−1∙ℓ−1 (equivalent to a 0.01 mg/ℓ residual in ozone demand-free water) was required to destroy both pathogens within 10 min.In untreated soft lake water 103 cells/ml of A. salmonicida survived only 2 days, while the ERM bacterium (103 cells/ml) survived even after 20 day s in soft and hard untreated lake waters.

Sign in / Sign up

Export Citation Format

Share Document