A Logical Problem Solving Process for High Via Resistance Root Cause Analysis

2008 ◽  
Author(s):  
K. Li ◽  
P. Liu ◽  
J. Teong ◽  
M. Lee ◽  
H. L. Yap
Keyword(s):  
Problem Solving ◽  
Failure Analysis ◽  
Failure Mechanism ◽  
High Resistance ◽  
Cause Analysis ◽  
Logical Problem ◽  
Root Cause ◽  
Analysis Process ◽  
Problem Solving Process

Abstract This paper presents a case study on via high resistance issue. A logical failure analysis process EDCA (Effect, Defect, Cause, and Action) is successfully applied to find out the failure mechanism, pinpoint the root cause and solve the problem. It sets up a very good example of how to do tough failure analysis in a controllable way.

Failure Analysis Methodology on Systematic Defect in ADC_PLL Ring Pattern Due to Plasma De-Chuck Process

2010 ◽  
Author(s):  
Ang Ghim Boon ◽  
Chen Changqing ◽  
Alfred Quah ◽  
Magdeliza ◽  
Indahwan Jony ◽  
...  
Keyword(s):  
Problem Solving ◽  
Failure Analysis ◽  
Failure Mechanism ◽  
Root Cause ◽  
Path Tracing ◽  
Analysis Methodology ◽  
Wafer Fab ◽  
Problem Solving Process

Abstract In this paper, a low yield case relating to a systematic array of failures in a ring pattern due to ADC_PLL failures on low yielding wafers will be studied. A systematic problem solving process based on the application of a variety of FA techniques such as TIVA, AFP current imaging, layout path tracing, PVC and XTEM together with Fab investigation is used to understand the root cause as well as failure mechanism proposed. This process is particularly critical in a wafer foundry in which there is minimal available data on the test condition setup to duplicate the exact failure. The ring pattern was due to systematically open via as a result of polymer built-up from plasma de-chuck issue. It would serve as a good reference for a wafer Fab that encounters such an issue.

Failure Analysis Case Study of Inductively Coupled Cross-Chip Signals

2016 ◽  
Author(s):  
Steven Loveless ◽  
Zhihong You ◽  
Tathagata Chatterjee ◽  
Badarish Subbannavar
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Individual Data ◽  
Cause Analysis ◽  
Inductively Coupled ◽  
Root Cause ◽  
Specific Device ◽  
Data Points ◽  
On Chip

Abstract This paper discusses a failure analysis case study in a highly integrated mixed signal device caused by inductive coupling of on-chip signals. The techniques utilized and the approach to root cause analysis are discussed in depth. The interactions between the device design and failure mechanism are identified in detail. Focus is placed on drawing conclusions from the sum of individual data points, and the discussion provides an analytical path by which similar failures can be isolated and specific device sensitivities can be identified.

Root Cause Analysis for Pin Leakage

2016 ◽  
Author(s):  
Zhigang Song ◽  
Jochonia Nxumalo ◽  
Manuel Villalobos ◽  
Sweta Pendyala
Keyword(s):  
Failure Analysis ◽  
Root Cause Analysis ◽  
Advanced Technology ◽  
Process Step ◽  
Cause Analysis ◽  
Hard Mask ◽  
Technology Node ◽  
Root Cause ◽  
Tools And Techniques

Abstract Pin leakage continues to be on the list of top yield detractors for microelectronics devices. It is simply manifested as elevated current with one pin or several pins during pin continuity test. Although many techniques are capable to globally localize the fault of pin leakage, root cause analysis and identification for it are still very challenging with today’s advanced failure analysis tools and techniques. It is because pin leakage can be caused by any type of defect, at any layer in the device and at any process step. This paper presents a case study to demonstrate how to combine multiple techniques to accurately identify the root cause of a pin leakage issue for a device manufactured using advanced technology node. The root cause was identified as under-etch issue during P+ implantation hard mask opening for ESD protection diode, causing P+ implantation missing, which was responsible for the nearly ohmic type pin leakage.

Root Cause Analysis of Glovebox Glove Failure

2007 ◽  
Author(s):  
Y. H. Park ◽  
Michael Cournoyer
Keyword(s):  
Safety Concern ◽  
National Laboratory ◽  
Root Cause Analysis ◽  
Nuclear Materials ◽  
Alamos National Laboratory ◽  
Cause Analysis ◽  
Los Alamos National Laboratory ◽  
Root Cause ◽  
Analysis Process

The Nuclear Materials Technology (NMT) Division has the largest inventory of glovebox gloves at Los Alamos National Laboratory (LANL). Consequently, the minimization of unplanned breaches of the glove material, typically resulting in glove failures, is a significant safety concern in the daily operations in NMT Division facilities. To investigate processes and procedures that minimize unplanned breaches in the glovebox, information on glovebox glove failures has been compiled from formal records and analyzed using statistical methods. Based on these research results, the next step of the research is to identify root causes of glove failures and the actions adequate to prevent recurrence. In this paper, root cause analysis was conducted for a cleanup breach case study to demonstrate the computerized root cause analysis process. Based on analysis results, effective recommendations were generated.

Tri-Directional TEM Failure Analysis on Sample Prepared by In-Situ Lift-Out FIB and Flipstage

2014 ◽  
Author(s):  
Jie Zhu ◽  
An Yan Du ◽  
Bing Hai Liu ◽  
Eddie Er ◽  
Si Ping Zhao ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Cross Section ◽  
Root Cause Analysis ◽  
Wafer Surface ◽  
Tem Analysis ◽  
Cause Analysis ◽  
Root Cause

Abstract In this paper, we report an advanced sample preparation methodology using in-situ lift-out FIB and Flipstage for tridirectional TEM failure analysis. A planar-view and two cross-section TEM samples were prepared from the same target. Firstly, a planar-view lamellar parallel to the wafer surface was prepared using in-situ lift-out FIB milling. Upon TEM analysis, the planar sample was further milled in the along-gate and cross-gate directions separately. Eventually, a pillar-like sample containing a single transistor gate was obtained. Using this technique, we are able to analyze the defect from three perpendicular directions and obtain more information on the defect for failure root-cause analysis. A MOSFETs case study is described to demonstrate the procedure and advantages of this technique.

A Study of SRAM Device Soft Failures Caused by Contact Volcano Defects Using Nanoprobing Analysis

2011 ◽  
Author(s):  
Yu Hsiang Shu ◽  
Vincent Huang ◽  
Chia Hsing Chao
Keyword(s):  
Failure Analysis ◽  
High Resistance ◽  
Ion Beam ◽  
Analysis Method ◽  
Root Cause ◽  
Parametric Data ◽  
Transmission Electron ◽  
Focus Ion Beam ◽  
Electrical Data

Abstract Using nanoprobing techniques to accomplish transistor parametric data has been reported as a method of failure analysis in nanometer scale defect. In this paper, we focus on how to identify the influence of Contact high resistance on device soft failures using nanoprobing analysis, and showing that the equivalent mathematical models could be used to describe the corresponding electrical data in a device with Contact high resistance issue. A case study was presented to verify that Contact volcano defect caused Contact high resistance issue, and this issue can be identified via physical failure analysis (PFA) method (e.g. Transmission Electron Microscope and Focus Ion Beam techniques) and nanoprobing analysis method. Finally, we would explain the physical root cause of Contact volcano issue.

Failure Analysis Methodology on Systematic Missing Cu in RAM Due to Cu CMP

2014 ◽  
Author(s):  
Ghim Boon Ang ◽  
Changqing Chen ◽  
Hui Peng Ng ◽  
Alfred Quah ◽  
Angela Teo ◽  
...  
Keyword(s):  
Problem Solving ◽  
Failure Analysis ◽  
Failure Mechanism ◽  
Removal Rate ◽  
Deep Dive ◽  
The Real ◽  
Root Cause ◽  
Analysis Methodology ◽  
Strong Emphasis ◽  
Cu Cmp

Abstract This paper places a strong emphasis on the importance of applying Systematic Problem Solving approach and use of appropriate FA methods and tools to understand the “real” failure root cause. A case of wafer center cluster RAM fail due to systematic missing Cu was studied. It was through a strong “inquisitive” mindset coupled with deep dive problem solving that lead to uncover the actual root cause of large Cu voids. The missing Cu was due to large Cu void induced by galvanic effects from the faster removal rate during Cu CMP and subsequently resulted in missing Cu. This highlights that the FA analyst’s mission is not simply to find defects but also play a catalyst role in root cause/failure mechanism understanding by providing supporting FA evidence (electrically/ physically) to Fab.

Humidity-Bias Driven Shorts in Multilayer Circuits: A Case Study in Failure Analysis

2000 ◽  
Author(s):  
Hei-Ruey Harry Jen ◽  
Gerald S. D’Urso ◽  
Harold Andrews
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Layer Structure ◽  
Molding Compound ◽  
Plastic Molding ◽  
Root Cause ◽  
Plastic Package ◽  
Processing Procedure ◽  
Failure Site

Abstract When a failure analysis (FA) involves a multiple layer structure separated by a polymeric material such as Benzocyclobutene (BCB), in a plastic package, it becomes a very challenging task to find out where the failure site is and how it failed. This is due to the fact that the chemical de-processing procedure removes BCB as well as the plastic molding compound. This paper outlines the studies carried out to determine the failure site and the root cause of the failure mechanism in a multilayer circuit and the steps taken to fix the problems. The methodology and results of this study are applicable to many other types of circuits.

Sign in / Sign up

Export Citation Format

Share Document