Relationship Between Particle Size Distribution and Specific Surface Area of Urban Roadway Stormwater Solids

1997 ◽  
Vol 1601 (1) ◽  
pp. 95-108 ◽  
Author(s):  
John J. Sansalone ◽  
Steven G. Buchberger ◽  
Joseph M. Koran ◽  
Joseph A. Smithson

Surface area is a primary factor in determining many physical and chemical properties of solids, especially particles. In urban and highway runoff, solids can mediate the partitioning between the dissolved and particulate-bound phases of metal elements and organic compounds. Solids are also capable of adversely affecting roadway drainage appurtenances through sedimentation and clogging. Solids characteristics of primary importance for both solute adsorption and clogging and sedimentation are particle size distributions (PSDs), specific surface areas (SSAs), and mass loadings. PSD and SSA results are presented for rainfall and snowmelt solids from a heavily traveled urban roadway in Cincinnati. Integration of the PSD and SSA results indicates that particle surface area is greatest for the midrange (> 100 μm) to the coarser end (<2000 μm) of the gradation. SSA results determined using the assumption of smooth spherical particles are indicated to grossly underestimate actual SSA values.

Author(s):  
Mingdong Li ◽  
Jiawei Wang ◽  
Dejin Fu ◽  
Bibo Gou ◽  
Xiaoliang Chen ◽  
...  

Abstract Manganese oxides showed many special physicochemical properties in many fields such as electrochemistry, adsorption and catalysis. They were widely used in cathode materials for lithium batteries, molecular sieves, catalytic materials and adsorbents. In this paper, in situ oxidation of manganese sulfate solution was conducted with H2O2 as oxidant, and the characterization means of XRD, SEM and BET were used. The purpose was to study the effects of different regulation mechanisms on the physical and chemical properties of manganese oxides such as morphology, phase composition, surface properties and specific surface area. The adsorption properties of γ-MnO2 for Co and Ni in manganese ore leaching solution were tested. The results showed as follows. Under alkaline conditions, the main product of manganese sulfate solution oxidized by H2O2 was Mn3O4 spherical particles with a radius of about 50 nm, these particles had micropores or mesopores, the oxidation reaction rate was rapid, and the specific surface area and N2 adsorption capacity changed with the change of reaction conditions.The temperature had a great influence on the micro morphology of the product.The micro morphology was slender nanorod when the temperature was 20℃. With the increase of temperature, the length of nanorod became shorter. When the temperature rises to 50℃, the rod became spherical. When the pH value decreased from 9 to 7, the diffraction peak of each crystal plane in the product Mn3O4 decreased gradually. The diffraction peak of γ-MnO2 appeared when the pH value decreased to 5. All the products were γ-MnO2 when the pH value decreased to 3. With the increase of Mn2+ concentration, the grain size decreased and agglomeration was easy to occur. The optimum conditions were obtained as follows: the temperature was 30℃, pH was 3, reaction time was 90 min, the mole ration of H2O2 to Mn2+ was 1:1, and Mn2+ concentration was 10g/L. Under the optimum conditions, γ-MnO2 with high specific surface area (172.41 m2/g) was prepared. This γ-MnO2 has a good adsorption effect on Co and Ni in manganese ore leaching solution, and the adsorption efficiency could be reached 94.75 % and 95.67 %. This study would provide a reference for the preparation of manganese oxides with different physical and chemical properties.


2020 ◽  
Vol 26 (1) ◽  
pp. 82-93
Author(s):  
Reihaneh Radmanesh ◽  
◽  
Mohsen Nabi Meybodi ◽  
Vahid Ramezani ◽  
Maryam Akrami ◽  
...  

Aims: Any pharmaceutical product made in pharmacy, hospital or factory may be contaminated with microbes. This contamination can originate from raw materials or during production. Hence, it is important to study the physical and chemical properties and stability of compounded drugs. Methods & Materials: In this study, first a specific sample of prescribed medication was ordered from 63 pharmacies in Yazd, Iran. After collecting the samples, the amount of microbial contamination, viscosity and particle size distribution and their stability were investigated and their results were compared to the standard levels. Findings: Based on the results, 31.7% of the samples had discoloration and 23.8% showed creaming phenomenon. In terms of particle size distribution, 57.1% of the samples had a 20-40 μm particle size and 49.2% had a viscosity equal to 2500-3000 centipoise. Regarding stability, 12.6% of the samples underwnet phase change at 30-40°C. About of the amount of hydroquinone in samples, 35% had acceptable amount. In 23.8% of the samples, fungal infection was observed. Conclusion: Contrary to a popular belief that the compounded medicines produced in pharmacies have microbial contamination, the results of this study showed that the microbial contamination of these compounded medications is low.


Paliva ◽  
2020 ◽  
pp. 155-161
Author(s):  
Tomáš Hlinčík ◽  
Veronika Šnajdrová ◽  
Veronika Kyselová

Alumina is commonly used in industrial practice as a catalyst support and it is made from boehmite. Depending on the calcination temperature, this mineral is transformed into various crystalline modifications which have different physical and chemical properties. For this reason, the following parameters were determined at different calcination temperatures: length, width, material hardness, specific surface area and total pore volume. The results show that with increasing calcination temperature there have been significant changes which may be important when using the material as a catalyst support, e.g. in the preparation of catalysts or in the design of cat-alytic reactors. The specific surface area, which decreases in the temperature range 450–800 °C, is an important parameter for the preparation of catalysts, so it is appropriate to choose a temperature of 600 °C, when the specific surface area is above 200 m2·g-1. The effect of calcination temperature on the structural transitions of boehmite was also monitored. The results showed that γ-Al2O3 has the most suitable properties as a catalyst sup-port in the temperature range 450–800 °C.


1986 ◽  
Vol 86 ◽  
Author(s):  
R. C. Joshi ◽  
B. K. Marsh

ABSTRACTThis paper gives physical and chemical properties of some Canadian fly ashes. Specific surface area, magnetic fraction, water soluble fraction and fraction finer than 45 μm were determined as part of the physical tests. Thermo-gravimetric analyses (TGA) in oxygen and nitrogen were conducted on raw ash samples. The change of pH with time in suspensions of the different ashes in water was also determined. Pozzolanic activity of the ashes with lime for all the ashes was evaluated to measure ash reactivity.The ash activity seems to be related to fineness of the ash measured by the Blaine air permeability method, but not to the fineness measured by nitrogen sorption. Generally the greater the specific surface area, the higher the reactivity of the ash. The correlation was, however, not strong and no other physical or chemical parameter measured in this investigation seems to be related to pozzolanic activity.The results of pH and TGA tests indicated that the ashes differ in many respects from each other. The TGA data suggest that loss on-ignition in many of the ashes is not entirely due to the presence of unburned carbon. Specific surface area determined by various methods seems to provide different values. No characterization parameter was found that was uniquely related to coal type.


2019 ◽  
Vol 58 (1) ◽  
pp. 179-188 ◽  
Author(s):  
Yong-Sik Chu ◽  
Batmunkh Davaabal ◽  
Dae-Sung Kim ◽  
Sung-Kwan Seo ◽  
Yoo Kim ◽  
...  

Abstract The effect of two different milling devices, namely attrition mill versus vibration mill, on the reactivity of fly ash was studied. High calcium fly ash from 4th Thermal power station of Ulaanbaatar (Mongolia) was used for the experiments. The raw and processed samples were characterized by XRD, SEM, Particle size distribution, BET, Blaine surface area and density measurements. The efficiency of 1 hour milling was evaluated with the Blaine surface area set to be more than 5000 cm2/g. The physical and chemical properties of the attrition milled fly ash changed not much compared to the vibration milled samples. For example the d50 particle size became reduced from 29 µm to 6 µm by attrition milling and in vibration milled fly ash it was reduced to 7 µm. The density increased from 2.44 g/cm3 of raw fly ash to 2.84 g/cm3 and 2.79 g/cm3 in attrition and vibration milled samples, respectively. Mechanical milling revealed not only a particle size reduction but also the formation of a denser microstructure. As a result the vibration milled fly ash showed a weaker interaction with the alkaline solution (8 M NaOH used here) compared to the attrition milled fly ash. Consequently, compressive strength of the binder prepared using the attrition milled fly ash was higher, 61 MPa, while for vibration milled fly ash it was 49 MPa. For comparison unmilled fly ash, it was 21 MPa.


2011 ◽  
Vol 485 ◽  
pp. 137-140 ◽  
Author(s):  
Kenichi Myoujin ◽  
Hiroki Ichiboshi ◽  
Takayuki Kodera ◽  
Takashi Ogihara

Spherical samarium doped ceria (Ce0.8Sm0.2O1.9, SDC) powders having high specific surface area (SSA) were successfully synthesized by carbon-assisted spray pyrolysis (CASP). Saccharides, such as monosaccharides and disaccharides, or organic acids were used as carbon sources. The physical and chemical properties of these powders were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), Thermo gravimetry-Differential Thermal Analysis (TG-DTA), and BET. Decarbonized powders obtained by this method exhibit spherical morphologies and nano- and submicron-sizes. The SSA of SDC obtained from CASP was more than seven times higher than that obtained from conventional spray pyrolysis (CSP). The SSA of the decarbonized SDC powders obtained by calcination at 900 °C was estimated to be approximately 70 m2/g by using the BET method. The relative density of SDC obtained from CASP was higher than that obtained from CSP. The relative density of the SDC pellet was highest (96 %) when it was sintered at 1400 °C.


1993 ◽  
Vol 23 (5) ◽  
pp. 941-955 ◽  
Author(s):  
K. Van Cleve ◽  
C.T. Dyrness ◽  
G.M. Marion ◽  
R. Erickson

Alluvial soils on the Tanana River floodplain near Fairbanks, Alaska, were examined for development of physical and chemical properties in relation to soil depth and across a 200-year vegetation development sequence. Development was mediated by ecosystem controls including successional time, vegetation, terrace height, soil physical and chemical properties, and microclimate. These controls interact and are conditioned by the state factors time, flora, topography, parent material, and climate, respectively. On early-successional (<5 years) lower alluvial surfaces, terrace height above groundwater, soil particle size, and microclimate (through soil surface evaporation) interacted through capillary rise to produce salt-affected surface soil. Calcium salts of carbonate and sulfate were the principal chemicals encountered in these soils. Establishment of a vegetation cover between 5 and 10 years introduced evapotranspiration as a new mechanism, along with capillarity, to control moisture suction gradients. In addition, newly formed surface litter layers further helped eliminate evaporation and formation of high salt content surface soil. Continued sedimentation raised terrace elevation, so on older terraces only infrequent flood events influenced soil development. Moreover, in these successional stages, only the highest river stages raised groundwater levels, so transpiration and capillarity influenced water movement to tree root systems. During the first 25–30 years of succession, plant deposition of organic matter and nitrogen, associated with the growth of alder, markedly changed soil properties. Nearly 60% (or 240 g•m−2) of the 400 g•m−2 nitrogen encountered at 100 years was accumulated during this early period. After 100 years of vegetation development, soil carbonate content dropped to about half the peak values of about 1600 g•m−2 encountered between 4 and 25 years. By the time white spruce was the dominant forest type at 180 years, carbonate carbon declined to about 500 g•m−2, one-third that of the 1600 g•m−2 high. By this time surface soil pH declined from high values of 7.5 to between 5.5 and 6.0. Organic carbon continued to accumulate to about 6300 g•m−2 in the white spruce stage, twice that encountered in the alder–poplar stage at 25 years. Indices of moisture retention were most strongly related to either soil particle size (low moisture tension and available moisture range) or vegetation-mediated soil organic matter content (high moisture tension). Cation exchange capacity was most strongly related to a vegetation-mediated index of organic matter (OM) content (%N, %C, or %OM).


Sign in / Sign up

Export Citation Format

Share Document