scholarly journals Modeling and Analysis of Axial Dynamics of Cable Arrangement Device Based on MATLAB

2021 ◽  
Author(s):  
Fankai Kong ◽  
Yucai Pan ◽  
Jiawei Zhao ◽  
Nan Zhang ◽  
Zhenyang Wang ◽  
...  
Keyword(s):  
Natural Frequency ◽  
Dynamic Equation ◽  
Lagrange Equation ◽  
Dynamics Analysis ◽  
Modeling And Analysis ◽  
System Parameters ◽  
First Order ◽  
Axial Forces ◽  
Damping Model ◽  
Force Characteristics

Aiming at the current insufficient dynamic analysis of the cable arrangement device, the axial dynamics analysis of the cable arrangement device is carried out in combination with the force characteristics of the cable arrangement device. The axial dynamic model of cable arrangement device is established by using spring-damping model, and the dynamic equation is established by using Lagrange equation. The influence of system parameters of cable arrangement device on axial first-order natural frequency is analyzed by numerical method. By fitting and loading the external excitation of the cable arrangement device, the axial dynamic response of the cable arrangement device under different axial forces is obtained. Through numerical results, the influence laws of the position and mass of the traveling mechanism and the support stiffness of the lead screw on the axial first-order natural frequency are obtained, It is found that the axial displacement of the cable arrangement device under axial force is very small, and the cable arrangement device has strong retention of dynamic characteristics. The results have certain guiding significance for the structural design and application environment of cable arrangement device.

Dynamics Analysis of Vibrating Screen Based on Double Compound Pendulum with Single Motor Driving

2013 ◽  
Vol 459 ◽  
pp. 335-341
Author(s):  
Yong Jun Hou
Keyword(s):  
Dynamic Equation ◽  
Lagrange Equation ◽  
Translational Motion ◽  
Simulation Method ◽  
Dynamics Analysis ◽  
Linear Trajectory ◽  
Single Motor ◽  
Vibrating Screen ◽  
Motion Characteristics ◽  
Screen Surface

By Lagrange equation, the dynamic equation of vibrating screen based on double compound pendulum with single motor driving was established. With simulation method, dynamic simulating model was built, and influences of pendulum installing position, stiffness of torsion damping spring of pendulum rod, initial installing angle and length of pendulum rod on motion characteristics of vibrating screen was discussed. Research results showed that, by choosing suitable stiffness of torsion damping spring or length of pendulum rod, this kind of vibrating screen may achieve the approximate linear trajectory, or normal elliptic trajectory of deck; when the angle between the rotating joint of pendulum rod and screen surface equals to initial installing angle of pendulum rod, the vibration of deck is most close to translational motion..

LATERAL-FLEXURAL AND TORSIONAL VIBRATIONS OF FLEXIBLE RING FOR ELECTROMECHANICAL INTEGRATED ELECTROSTATIC HARMONIC ACTUATOR

2009 ◽  
Vol 09 (03) ◽  
pp. 391-409
Author(s):  
LIZHONG XU ◽  
YAOWU LI
Keyword(s):  
Natural Frequency ◽  
Dynamic Equation ◽  
Forced Response ◽  
Dynamic Responses ◽  
Torsional Vibrations ◽  
Vibration Modes ◽  
System Parameters ◽  
Electromechanical Integrated ◽  
Flexible Ring ◽  
Electromechanical Coupled

This paper presents an electromechanical coupled dynamic equation for the lateral-flexural and torsional vibrations of a flexible ring for an electromechanical integrated electrostatic harmonic actuator as well as the equation of the forced response of the electromechanical integrated electrostatic harmonic actuator to voltage excitation. By solving these equations, the natural frequency and vibration modes of the flexible ring for the actuator are investigated. Changes in the natural frequency with respect to the main system parameters are also examined and the dynamic responses of the actuator to voltage excitation obtained.

A Study on Dynamics of 2-PRR Parallel Machine Tool Based on the Lagrange Equation

2011 ◽  
Vol 295-297 ◽  
pp. 1373-1379
Author(s):  
Suo Xian Yuan ◽  
Dan Dan Shen
Keyword(s):  
Machine Tool ◽  
Dynamic Equation ◽  
Lagrange Equation ◽  
Parallel Machine ◽  
Displacement Velocity ◽  
Dynamics Analysis ◽  
Moving Platform ◽  
Parallel Machine Tool

Based on the Lagrange equation, a dynamic equation of 2-PRR parallel machine tool has been established and the relation among displacement,velocity and acceleration of moving platform was given. By modeling and simulating on the simulink of Matlab, forword dynamics are solved. This paper also provide a reference for dynamics analysis and optimization of less freedom machine tool

Dynamics Analysis of Refrigeration Compressor Based on Finite Element and Experimental Modes

2012 ◽  
Vol 499 ◽  
pp. 238-242
Author(s):  
Li Zhang ◽  
Hong Wu ◽  
Yan Jue Gong ◽  
Shuo Zhang
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Modal Analysis ◽  
Natural Frequency ◽  
High Precision ◽  
3D Model ◽  
Finite Element Models ◽  
Dynamics Analysis ◽  
Response Characteristics ◽  
Dynamic Response Characteristics

Based on the 3D model of refrigeration's compressor by Pro/E software, the analyses of theoretical and experimental mode are carried out in this paper. The results show that the finite element models of compressor have high precision dynamic response characteristics and the natural frequency of the compressor, based on experimental modal analysis, can be accurately obtained, which will contribute to further dynamic designs of mechanical structures.

Reduced Order Model of MEMS Sensors Near Natural Frequency

2011 ◽  
Author(s):  
Dumitru I. Caruntu ◽  
Jose C. Solis Silva
Keyword(s):  
Natural Frequency ◽  
Nonlinear Response ◽  
Casimir Effect ◽  
Electrostatic Force ◽  
Reduced Order Model ◽  
Mass Detection ◽  
Order Model ◽  
Reduced Order ◽  
First Order ◽  
Electrostatically Actuated

The nonlinear response of an electrostatically actuated cantilever beam microresonator sensor for mass detection is investigated. The excitation is near the natural frequency. A first order fringe correction of the electrostatic force, viscous damping, and Casimir effect are included in the model. The dynamics of the resonator is investigated using the Reduced Order Model (ROM) method, based on Galerkin procedure. Steady-state motions are found. Numerical results for uniform microresonators with mass deposition and without are reported.

scholarly journals Design optimization of vehicle asynchronous motors based on fractional harmonic response analysis

2021 ◽  
Vol 12 (1) ◽  
pp. 689-700
Author(s):  
Ao Lei ◽  
Chuan-Xue Song ◽  
Yu-Long Lei ◽  
Yao Fu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Natural Frequency ◽  
Asynchronous Motor ◽  
Element Model ◽  
Design Parameters ◽  
Response Analysis ◽  
Harmonic Response ◽  
First Order ◽  
Harmonic Response Analysis

Abstract. To make vehicles more reliable and efficient, many researchers have tried to improve the rotor performance. Although certain achievements have been made, the previous finite element model did not reflect the historical process of the motor rotor well, and the rigidity and mass in rotor optimization are less discussed together. This paper firstly introduces fractional order into a finite element model to conduct the harmonic response analysis. Then, we propose an optimal design framework of a rotor. In the framework, objective functions of rigidity and mass are defined, and the relationship between high rigidity and the first-order frequency is discussed. In order to find the optimal values, an accelerated optimization method based on response surface (ARSO) is proposed to find the suitable design parameters of rigidity and mass. Because the higher rigidity can be transformed into the first-order natural frequency by objective function, this paper analyzes the first-order frequency and mass of a motor rotor in the experiment. The results proved that not only is the fractional model effective, but also the ARSO can optimize the rotor structure. The first-order natural frequency of asynchronous motor rotor is increased by 11.2 %, and the mass is reduced by 13.8 %, which can realize high stiffness and light mass of asynchronous motor rotors.

A Modal Analysis of Giant Shipbuilding Tower Crane

2012 ◽  
Vol 239-240 ◽  
pp. 473-477 ◽  
Author(s):  
Guo Jian Huang ◽  
Cheng Zhong He ◽  
Xin Hua Wang
Keyword(s):  
Modal Analysis ◽  
Natural Frequency ◽  
Theoretical Basis ◽  
Safety Evaluation ◽  
Structural Instability ◽  
Dynamics Analysis ◽  
Vibration Frequencies ◽  
Corrosive Environment ◽  
Tower Crane ◽  
Modal Vibration

Old giant cranes in corrosive environment are in serious hidden danger of structural instability and failure, the modal analysis is an important part of dynamics analysis in the Crane Safety Evaluation to guarantee the safety of cranes. A Modal Analysis of a 28-year old 100t giant shipbuilding tower crane was done using ANSYS. Comparing with the vibration frequencies and modal shapes, Modal analysis shows that the Natural Frequency of the crane reduces from 1.0024Hz to 1.0003Hz, beside all the Modal vibration frequencies (first 10 Order) of the crane are lower than the designed value, means the strength of the tower crane has decreased; the Modal Vibration Frequencies (first 10 Order) of the tower crane are between 1 Hz and 2 Hz. The Mmodal analysis provided theoretical basis for safe use, design and transformation of this crane.

Measurement of axial forces via natural frequency

1998 ◽  
Author(s):  
Samer H. Petro ◽  
Don Reynolds ◽  
Shen EnChen ◽  
Hota V. S. GangaRao
Keyword(s):  
Natural Frequency ◽  
Axial Forces

Eigensensitivity of Planetary Gear Free Vibration Properties

1999 ◽  
Author(s):  
Jian Lin ◽  
Robert G. Parker
Keyword(s):  
Kinetic Energy ◽  
Free Vibration ◽  
Natural Frequency ◽  
Vibration Mode ◽  
Planetary Gear ◽  
Planetary Gears ◽  
System Parameters ◽  
Frequency Sensitivity ◽  
Vibration Properties ◽  
Inertia Parameters

Abstract The natural frequency and vibration mode sensitivities to system parameters are rigorously investigated for both tuned and mistimed planetary gears. Parameters under consideration include support and mesh stiffnesses, component masses, and moments of inertia. Using the well-defined vibration mode properties of tuned (cyclically symmetric) planetary gears [1], the eigensensitivities are calculated and expressed in simple, exact formulae. These formulae connect natural frequency sensitivity with the modal strain or kinetic energy and provide efficient means to determine the sensitivity to all stiffness and inertia parameters by inspection of the modal energy distribution. While the terminology of planetary gears is used throughout, the results apply for general epicyclic gears.

Probabilistic Analysis on the Uncertainty in Natural Frequency of Functionally Graded Material Beams

2019 ◽  
Vol 889 ◽  
pp. 484-488
Author(s):  
Van Thuan Nguyen ◽  
Duy Liem Nguyen
Keyword(s):  
Elastic Modulus ◽  
Natural Frequency ◽  
Functionally Graded Material ◽  
Functionally Graded ◽  
Order Perturbation ◽  
First Order ◽  
Graded Material ◽  
Natural Frequency Analysis ◽  
Mcs Method ◽  
First Order Perturbation

This paper applies the stochastic finite element method (SFEM) to perform the natural frequency analysis of functionally graded material (FGM). It is assumed that the elastic modulus and width of the FGM beam vary along the thickness and width directions following exponential functions. The stochastic eigenvalue problem is solved independently by first-order perturbation and Monte Carlo simulation (MCS) method through changing elastic modulus as spatial randomness. The results show that the first-order perturbation method based SFEM produces a very close value to MCS method.

Sign in / Sign up

Export Citation Format

Share Document