scholarly journals Study on the Rheological Properties of Ultra-High Temperature CGA Drilling Fluids

2021 ◽  
Author(s):  
Wenxi Zhu ◽  
Xiuhua Zheng
Keyword(s):  
High Temperature ◽  
Rheological Properties ◽  
High Temperatures ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Underbalanced Drilling ◽  
Deep Wells ◽  
Colloidal Gas Aphron ◽  
Oil Gas ◽  
Ultra High Temperature

Colloidal gas aphron (CGA) drilling fluids are a kind of environmentally-friendly underbalanced drilling technique, which has attracted more attention in depleted reservoirs and other low-pressure areas. With the shortage of global oil/gas resources, drilling has gradually shifted to high-temperature and deep wells. Hence, a study on the ultra-high temperature rheology properties of CGA fluids is lacking and urgently needed. In this study, a novel CGA drilling fluid system was prepared by modified starch and amino acid surfactant, and rheological properties after 120-300°C aged was investigate. Results show that: (1) Herschel-Bulkley model is the preferred model to predict CGA drilling fluid at ultra-high temperatures; (2) It was proved that CGA drilling fluid is a high-quality drilling fluid with extremely high value of LSRV and shear thinning property within 280°C. Compared to the traditional XG-based CGA drilling fluid, the improvement of LSRV at ultra-high temperatures is a significant advantage of EST-based CGA drilling fluid which is conducive to carrying cuttings and sealing formation pores.

scholarly journals The application of MWCNT to enhance the rheological behavior of drilling fluids at high temperature

2017 ◽  
Vol 12 (3) ◽  
Author(s):  
Abdul Razak Ismail ◽  
W. R. W Sulaiman ◽  
M. Z. Jaafar ◽  
A. Aftab ◽  
A. A. Razi ◽  
...  
Keyword(s):  
High Temperature ◽  
Rheological Properties ◽  
Rheological Behavior ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Gel Strength ◽  
Drilling Fluids ◽  
Deep Wells ◽  
Multi Walled Carbon Nanotube ◽  
Filtrate Loss

Drilling fluid is the key component to drill oil and gas wells. The rheological behavior of drilling fluid will be affected when drilling deep wells especially at high temperature and high pressure reservoir. This research was conducted to study the effect of the nanoparticles over the rheological properties of the drilling fluid when aging at high temperature condition. Several drilling fluids were prepared using synthetic based fluids (Sarapar and Saraline) to study the effect of multi-walled carbon nanotube (MWCNT) at different concentrations. The rheological properties of drilling fluid were analyzed after aging at 250 °F and 350 °F for 16 hours. The results revealed that the addition of MWCNT improved the 10-sec gel strength by 33% and filtrate loss volume was reduced to 10% after aging at 250°F in Saraline drilling fluid. Moreover, the plastic viscosity of Saraline and Sarapar drilling fluid after addition of MWCNT was enhanced by 6% and 27% at 350 °F. Filtrate loss volume of Sarapar drilling fluid was reduced by 19 % after aging at 250 °F for 16 hours. The overall results showed that the addition of MWCNT into the drilling fluid have slightly improved the rheological properties of drilling fluids under high temperature conditions.

Improving the rheological properties of water-based calcium bentonite drilling fluids using water-soluble polymers in high temperature applications

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Jinliang Liu ◽  
Fengshan Zhou ◽  
Fengyi Deng ◽  
Hongxing Zhao ◽  
Zhongjin Wei ◽  
...  
Keyword(s):  
High Temperature ◽  
Rheological Properties ◽  
Apparent Viscosity ◽  
Drilling Fluid ◽  
Shear Thickening ◽  
Water Soluble ◽  
Drilling Fluids ◽  
Drilling Depth ◽  
Filtration Loss ◽  
Calcium Bentonite

Abstract Most of bentonite used in modern drilling engineering is physically and chemically modified calcium bentonite. However, with the increase of drilling depth, the bottom hole temperature may reach 180 °C, thus a large amount of calcium bentonite used in the drilling fluid will be unstable. This paper covers three kinds of calcium bentonite with poor rheological properties at high temperature, such as apparent viscosity is greater than 45 mPa·s or less than 10 mPa·s, API filtration loss is greater than 25 mL/30 min, which are diluted type, shear thickening type and low-shear type, these defects will make the rheological properties of drilling fluid worse. The difference is attributed to bentonite mineral composition, such as montmorillonite with good hydration expansion performance. By adding three kinds of heat-resistant water-soluble copolymers Na-HPAN (hydrolyzed polyacrylonitrile sodium), PAS (polycarboxylate salt) and SMP (sulfomethyl phenolic resin), the rheological properties of calcium bentonite drilling fluids can be significantly improved. For example, the addition of 0.1 wt% Na-HPAN and 0.1 wt% PAS increased the apparent viscosity of the XZJ calcium bentonite suspension from 4.5 to 19.5 mPa·s at 180 °C, and the filtration loss also decreased from 20.2 to 17.8 mL.

Application of modified starch in high-temperature-resistant colloidal gas aphron (CGA) drilling fluids

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Wenxi Zhu ◽  
Xiuhua Zheng
Keyword(s):  
High Temperature ◽  
High Temperatures ◽  
High Performance ◽  
Oil And Gas ◽  
Elevated Temperatures ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Modified Starch ◽  
Gas Reservoirs ◽  
Building Capability

Abstract Colloidal gas aphrons (CGA) are finding increasing application in depleted oil and gas reservoirs because of their distinctive characteristics. To overcome the limitations of its application in high-temperature drilling, a modified starch foams stabilizer WST with a temperature resistance of 160 °C was synthesized via radical polymerization. The chemical structure of WST was characterized by Fourier infrared spectroscopy and results showed that all three monomers acrylamide, 2-acrylamido-2-methyl-1-propane sulfonic acid, and N-vinylpyrrolidone have been grafted onto starch efficiently. Based on the microscopic observations, highly stable aphrons have been successfully generated in the WST-based CGA drilling fluids within 160 °C, and most aphrons lie in the range of 10–150 μm. WST can provide higher viscosity at high temperatures compared to xanthan gum, which helps to extend foam life and stability by enhancing the film strength and slowing down the gravity drainage. Results show that WST-CGA aged at elevated temperatures (120–160 °C) is a high-performance drilling fluid with excellent shear-thinning behavior, cutting carrying capacity, and filtration control ability. The significant improvement of filtration control and well-building capability at high temperatures is an important advantage of WST-CGA, which can be attributed to the enhancement of mud cake quality by WST.

scholarly journals High temperature and high pressure rheological properties of high-density water-based drilling fluids for deep wells

2012 ◽  
Vol 9 (3) ◽  
pp. 354-362 ◽  
Author(s):  
Fuhua Wang ◽  
Xuechao Tan ◽  
Ruihe Wang ◽  
Mingbo Sun ◽  
Li Wang ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Rheological Properties ◽  
High Density ◽  
Drilling Fluids ◽  
Deep Wells ◽  
Water Based

Improvement of Rheological and Filtration Properties of Water-Based Drilling Fluids Using Bentonite-Hydrothermal Carbon Nanocomposites Under the Ultra-High Temperature and High Pressure Conditions

2021 ◽  
Author(s):  
Hanyi Zhong ◽  
Ying Guan ◽  
Zhengsong Qiu ◽  
Jie Feng ◽  
Wenlei Liu ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Hydrothermal Reaction ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Deep Drilling ◽  
Carbon Nanocomposites ◽  
Water Based ◽  
Filtration Properties ◽  
Oil Gas

Abstract With the depletion of the conventional shallow oil/gas reservoirs and the increasing demand for oil and gas, deep drilling become more and more essential to extract the oil/gas from deep formations. However, deep drilling faces many complex challenges. One of the complexities is the degradation of polymers and flocculation of bentonite particles, leading to hardly control the rheological and filtration properties of water-based drilling fluids, especially under ultra-high temperature and high pressure (HTHP) conditions. Therefore, an experimental investigation is performed to study how bentonite-hydrothermal carbon nanocomposites will influence the rheological and filtration properties of water-based drilling fluids under ultra-HTHP conditions. Bentonite-hydrothermal carbon nanocomposites are proposed as non-polymer additives to solve the ultra-HTHP challenge in water-based drilling fluid. The nanocomposites are synthesized by facile hydrothermal reaction, in which biomass starch and sodium bentonite are used as the precursor and template, respectively. In this study, the effect of the nanocomposites on the rheology and filtration properties of water-based drilling fluid are investigated before and after hot rolling at 220 °C and 240 °C. The structure characterization indicates that carbon nanospheres can successfully deposit on the bentonite surface after hydrothermal reaction and finally form as nanocomposites. The elemental carbon content, zeta potential and particle size distribution of the nanocomposites could be adjusted according to the reaction conditions. After thermal aging at 220 °C and 240 °C, addition of nanocomposites can improve the rheological properties significantly where a stable and minor change of rheological properties is observed, which is desirable for ultra-HTHP drilling. Regarding filtration control, after adding 1.0 wt% nanocomposite materials, the filtration loss is reduced by 41% and 44% respectively after aging at 220 °C and 240 °C, which is better than the conventional natural materials that lose their function in this case. The identification of microstructure shows that the hydrothermal reaction endows nanocomposites with a unique surface morphology and an improved surface charge density. The interaction between nanocomposites and bentonite particles forms a rigid connection network, which is the main mechanism to facilitate effective rheology and filtration control under ultra-HTHP conditions. The green and facile synthetic routes and environmentally friendly features of the nanocomposites, coupled with the excellent performance in ultra-HTHP rheology and filtration control, indicate that the nanocomposites have a high promise for water-based drilling fluid in ultra-HTHP drilling. Moreover, it provides a new way to design high performance additives with high temperature stability.

Rheological Properties of Water-Based Drilling Fluids in Deep Offshore Conditions

2019 ◽  
Author(s):  
Qian Ding ◽  
Baojiang Sun ◽  
Zhiyuan Wang ◽  
Yonghai Gao ◽  
Yu Gao ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Low Temperature ◽  
Rheological Properties ◽  
Apparent Viscosity ◽  
Drilling Fluid ◽  
Plastic Viscosity ◽  
Drilling Fluids ◽  
Water Based ◽  
Temperature And Pressure

Abstract In deep-water drilling, the drilling fluid is affected by the alternating temperature field derived from the low temperature of the seawater and the high temperature of the formation. The complicated wellbore temperature and pressure environments make the prediction of rheological properties of the drilling fluid difficult. In this study, the rheological properties of water-based drilling fluid in full temperature and pressure range of deep-water conditions were tested from 2 to 150 °C (35.6 to 302 °F) and 0.1 to 70 MPa (14.5 to 10000psi). The experiment was carried out by the OFI130-77 high temperature and high pressure rheometer. The experimental data were processed by multiple regression analysis method, and the mathematical model for predicting the apparent viscosity, plastic viscosity and yield point of water-based drilling fluid under high temperature and high pressure conditions was established. The experimental results show that when the temperature is lower than 65 °C (149 °F), the apparent viscosity and plastic viscosity of the water-based drilling fluid decrease significantly with increasing temperature. When the temperature is higher than 65 °C (149 °F), the apparent viscosity and plastic viscosity decrease slowly. Under low temperature conditions, the effect of pressure on the apparent viscosity and plastic viscosity of water-based drilling fluids is relatively significant. The calculated values of the prediction model have a good agreement with the experimental measurements. Compared with the traditional model, this prediction model has a significant improvement in the prediction accuracy in the low temperature section, which can provide a calculation basis for on-site application of deepwater drilling fluid.

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Arild Saasen
Keyword(s):  
Rheological Properties ◽  
Pressure Loss ◽  
Drilling Fluid ◽  
Axial Flow ◽  
Drilling Fluids ◽  
Unstable Flow ◽  
Pressure Losses ◽  
Shear Dependent Viscosity ◽  
Water Based ◽  
Dependent Viscosity

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

Development of Digital Twins for Drilling Fluids: Local Velocities for Hole Cleaning and Rheology Monitoring

2021 ◽  
Author(s):  
Mehrdad Gharib Shirangi ◽  
Roger Aragall ◽  
Reza Ettehadi ◽  
Roland May ◽  
Edward Furlong ◽  
...  
Keyword(s):  
Machine Learning ◽  
Rheological Properties ◽  
Drilling Fluid ◽  
Training Data ◽  
Drilling Fluids ◽  
Hole Cleaning ◽  
Digital Twins ◽  
Wide Range ◽  
Drilling Operations ◽  
Cuttings Bed

Abstract In this work, we present our advances to develop and apply digital twins for drilling fluids and associated wellbore phenomena during drilling operations. A drilling fluid digital twin is a series of interconnected models that incorporate the learning from the past historical data in a wide range of operational settings to determine the fluids properties in realtime operations. From several drilling fluid functionalities and operational parameters, we describe advancements to improve hole cleaning predictions and high-pressure high-temperature (HPHT) rheological properties monitoring. In the hole cleaning application, we consider the Clark and Bickham (1994) approach which requires the prediction of the local fluid velocity above the cuttings bed as a function of operating conditions. We develop accurate computational fluid dynamics (CFD) models to capture the effects of rotation, eccentricity and bed height on local fluid velocities above cuttings bed. We then run 55,000 CFD simulations for a wide range of operational settings to generate training data for machine learning. For rheology monitoring, thousands of lab experiment records are collected as training data for machine learning. In this case, the HPHT rheological properties are determined based on rheological measurement in the American Petroleum Institute (API) condition together with the fluid type and composition data. We compare the results of application of several machine learning algorithms to represent CFD simulations (for hole cleaning application) and lab experiments (for monitoring HPHT rheological properties). Rotating cross-validation method is applied to ensure accurate and robust results. In both cases, models from the Gradient Boosting and the Artificial Neural Network algorithms provided the highest accuracy (about 0.95 in terms of R-squared) for test datasets. With developments presented in this paper, the hole cleaning calculations can be performed more accurately in real-time, and the HPHT rheological properties of drilling fluids can be estimated at the rigsite before performing the lab experiments. These contributions advance digital transformation of drilling operations.

scholarly journals Experimental Investigation of the Rheological Behavior of an Oil-Based Drilling Fluid with Rheology Modifier and Oil Wetter Additives

Molecules ◽  
2021 ◽  
Vol 26 (16) ◽  
pp. 4877
Author(s):  
Mobeen Murtaza ◽  
Sulaiman A. Alarifi ◽  
Muhammad Shahzad Kamal ◽  
Sagheer A. Onaizi ◽  
Mohammed Al-Ajmi ◽  
...  
Keyword(s):  
High Temperature ◽  
Zeta Potential ◽  
Hot Rolling ◽  
Emulsion Stability ◽  
Drilling Fluid ◽  
Temperature Tolerance ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Before And After ◽  
Rheology Modifier

Drilling issues such as shale hydration, high-temperature tolerance, torque and drag are often resolved by applying an appropriate drilling fluid formulation. Oil-based drilling fluid (OBDF) formulations are usually composed of emulsifiers, lime, brine, viscosifier, fluid loss controller and weighting agent. These additives sometimes outperform in extended exposure to high pressure high temperature (HPHT) conditions encountered in deep wells, resulting in weighting material segregation, high fluid loss, poor rheology and poor emulsion stability. In this study, two additives, oil wetter and rheology modifier were incorporated into the OBDF and their performance was investigated by conducting rheology, fluid loss, zeta potential and emulsion stability tests before and after hot rolling at 16 h and 32 h. Extending the hot rolling period beyond what is commonly used in this type of experiment is necessary to ensure the fluid’s stability. It was found that HPHT hot rolling affected the properties of drilling fluids by decreasing the rheology parameters and emulsion stability with the increase in the hot rolling time to 32 h. Also, the fluid loss additive’s performance degraded as rolling temperature and time increased. Adding oil wetter and rheology modifier additives resulted in a slight loss of rheological profile after 32 h and maintained flat rheology profile. The emulsion stability was slightly decreased and stayed close to the recommended value (400 V). The fluid loss was controlled by optimizing the concentration of fluid loss additive and oil wetter. The presence of oil wetter improved the carrying capacity of drilling fluids and prevented the barite sag problem. The zeta potential test confirmed that the oil wetter converted the surface of barite from water to oil and improved its dispersion in the oil.

Meeting Drilling Fluid Challenges in Gulf of Thailand Ultra High Temperature Exploration Wells

2014 ◽  
Author(s):  
Kerati Charnvit ◽  
Fransiskus Huadi ◽  
Chakkrawut Promkhote ◽  
Catalin Aldea ◽  
David Power ◽  
...  
Keyword(s):  
High Temperature ◽  
Drilling Fluid ◽  
Gulf Of Thailand ◽  
Ultra High Temperature
Sign in / Sign up

Export Citation Format

Share Document