scholarly journals Analysis of Polish norms on thermal resistance and thermal comfort for underfloor heating

2021 ◽  
Vol 37 ◽  
pp. 31-39
Author(s):  
A. Ujma
Keyword(s):  
Thermal Resistance ◽  
Surface Temperature ◽  
Low Grade ◽  
Renewable Energy Resources ◽  
Transfer Resistance ◽  
Floor Surface ◽  
Percentage Difference ◽  
Lower Temperature ◽  
Favorable Conditions ◽  
Low Grade Heat

In the paper, there is an analysis of the requirements for the thermal resistance of floors with underfloor heating. It corresponds to the human physiology as much as possible, creates comfortable conditions at a lower temperature of the internal air, reduces the rise of dust by reducing convective flows, allows the use of low-grade heat carriers, especially from secondary and renewable energy resources, does not take up space in the room, minimally affects the interior. However, the temperature of the heating elements is significantly higher than the room temperature. At the same time, the requirements for thermal insulation under the heating elements should be higher than for structures without heating. As the analysis of the regulations in force in Poland has shown, this is not always observed. In many cases, the heat transfer resistance is lower by 42-181 %. The percentage difference in requirements for flooers over aisles in rooms with an air temperature of 16 °C and above is 160%. It will reach 215 %, according to the requirements that will be applied from 2021. In the case of floors over unheated rooms, the percentage difference between the requirements reaches 181 %. By the new norms in 2021, this difference will reach 215 %. Also, the normative limitation on the temperature of the floor surface does not always allow providing the normative level of comfort. In rooms of categories A and B, the surface temperature of the floor must be 20-28 °C. In the case of category C it should not exceed 30 °C. The most favorable conditions are achieved when the floor surface temperature is close to 23.5 °C. PN-EN 1264-4 standard allows the temperature of the floor surface in some rooms up to 33...35 °C. Thus, to ensure energy efficiency and comfort, it is necessary to harmonize the regulations with each other.

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

scholarly journals Thermally regenerative electrochemical cycle for low-grade heat harnessing

2021 ◽  
Vol 2 (2) ◽  
pp. 021304
Author(s):  
Hang Zhang ◽  
Qing Wang
Keyword(s):  
Low Grade ◽  
Low Grade Heat

scholarly journals Low‐Grade Heat Harvesting: Efficient Low‐Grade Heat Harvesting Enabled by Tuning the Hydration Entropy in an Electrochemical System (Adv. Mater. 13/2021)

2021 ◽  
Vol 33 (13) ◽  
pp. 2170096
Author(s):  
Caitian Gao ◽  
Yezhou Liu ◽  
Bingbing Chen ◽  
Jeonghun Yun ◽  
Erxi Feng ◽  
...  
Keyword(s):  
Low Grade ◽  
Electrochemical System ◽  
Low Grade Heat

scholarly journals Enhanced Thermoelectric Performance of n-Type Bi2Se3 Nanosheets through Sn Doping

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1827
Author(s):  
Mengyao Li ◽  
Yu Zhang ◽  
Ting Zhang ◽  
Yong Zuo ◽  
Ke Xiao ◽  
...  
Keyword(s):  
Figure Of Merit ◽  
Cost Effective ◽  
Low Grade ◽  
Hot Press ◽  
Processing Technologies ◽  
Sn Doping ◽  
Practical Applications ◽  
Alternative Materials ◽  
The Cost ◽  
Low Grade Heat

The cost-effective conversion of low-grade heat into electricity using thermoelectric devices requires developing alternative materials and material processing technologies able to reduce the currently high device manufacturing costs. In this direction, thermoelectric materials that do not rely on rare or toxic elements such as tellurium or lead need to be produced using high-throughput technologies not involving high temperatures and long processes. Bi2Se3 is an obvious possible Te-free alternative to Bi2Te3 for ambient temperature thermoelectric applications, but its performance is still low for practical applications, and additional efforts toward finding proper dopants are required. Here, we report a scalable method to produce Bi2Se3 nanosheets at low synthesis temperatures. We studied the influence of different dopants on the thermoelectric properties of this material. Among the elements tested, we demonstrated that Sn doping resulted in the best performance. Sn incorporation resulted in a significant improvement to the Bi2Se3 Seebeck coefficient and a reduction in the thermal conductivity in the direction of the hot-press axis, resulting in an overall 60% improvement in the thermoelectric figure of merit of Bi2Se3.

scholarly journals Rolling membrane powered by low-temperature steam as a new approach to generate mechanical energy

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Chongshan Yin ◽  
Qicheng Liu ◽  
Qing Liu
Keyword(s):  
Water Vapor ◽  
Low Temperature ◽  
Combustion Engine ◽  
Mechanical Energy ◽  
Heat Energy ◽  
Steam Engine ◽  
Low Grade ◽  
Human Society ◽  
New Approach ◽  
Low Grade Heat

Abstract How to convert heat energy into other forms of usable energy more efficiently is always crucial for our human society. In traditional heat engines, such as the steam engine and the internal combustion engine, high-grade heat energy can be easily converted into mechanical energy, while a large amount of low-grade heat energy is usually wasted owing to its disadvantage in the temperature level. In this work, for the first time, the generation of mechanical energy from both high- and low-temperature steam is implemented by a hydrophilic polymer membrane. When exposed to water vapor with a temperature ranging from 50 to 100 °C, the membrane repeats rolling from one side to another. In nature, this continuously rolling of membrane is powered by the steam, like a miniaturized “steam engine”. The differential concentration of water vapor (steam) on the two sides of the membrane generates the asymmetric swelling, the curve, and the rolling of the membrane. In particular, results suggest that this membrane based “steam engine” can be powered by the steam with a relatively very low temperature of 50 °C, which indicates a new approach to make use of both the high- and low-temperature heat energy.

Influence of Covering Layer on Surface Temperature of Floor Radiant Heating System

2012 ◽  
Vol 204-208 ◽  
pp. 4260-4263 ◽  
Author(s):  
Hai Qian Zhao ◽  
Zhong Hua Wang ◽  
Lan Shuang Zhang
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Heating System ◽  
Radiant Heating ◽  
Wooden Floor ◽  
Surface Temperature Distribution ◽  
Covering Layer ◽  
Floor Surface ◽  
Space Saving ◽  
Cover Material

Floor radiant heating system has many advantages, energy and space saving, for example. The radiant floor is the radiator of floor radiant heating system, and its thermal parameters influence surface temperature distribution and comfort. In this paper, mathematical model of heat exchange coil under floor was established, and boundary heat transfer conditions were given. Based on these, surface temperature of different covering layer was calculated. According to the results, using different covering layer, the floor surface temperature has a great difference. Using wooden floor as cover material, the floor surface temperature is more moderate and uniform.

Sign in / Sign up

Export Citation Format

Share Document