scholarly journals Utilization of PET Fiber in Concrete

2019 ◽  
pp. 204-212
Keyword(s):  
Flexural Strength ◽  
Fiber Reinforced Concrete ◽  
Fine Aggregate ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Bottles ◽  
Curing Period ◽  
Daunting Task ◽  
Concrete Mix ◽  
Pet Fibers

In this study, the effectiveness of waste Polyethylene Terephthalate (PET) fibers in improving the properties of concrete was investigated. Recycling of waste PET bottles is a daunting task in developing countries due to inadequate recycling facilities. The main aim of this research paper is to investigate the mechanical behavior of the components by using PET fibers. This paper describes the performance of PET fiber reinforced concrete for two grades of concrete mix M20 and M30. An experimental work has been carried out on the specimens like cubes, cylinders and beams which were casted in the laboratory and their behavior under the test was observed. The PET fibers were replaced to the fine aggregate volume from 0.0% to 2.0%. The compressive strength, split tensile strength and flexural strength of concrete were determined after 28 days of curing period. The highest compressive, split tensile and flexural strength of concrete was observed at 1.5% fiber volume replacement to the fine aggregate. The study concludes that the replacement of waste PET fibers to fine aggregate in concrete serves as a means of utilizing the waste generated by PET bottles to increase the strength of concrete.

scholarly journals Influence of the Fiber Volume Content on the Durability-Related Properties of Polypropylene-Fiber-Reinforced Concrete

2020 ◽  
Vol 12 (2) ◽  
pp. 549
Author(s):  
Chenfei Wang ◽  
Zixiong Guo ◽  
Ditao Niu
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Volume Content ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Freeze Thaw ◽  
Chloride Environment ◽  
Polypropylene Fiber Reinforced Concrete

Polypropylene-fiber-reinforced concrete impacts the early shrinkage during the plastic stage of concrete, and the fiber volume content influences the durability-related properties of concrete. The purpose of this paper was to investigate the influence of fiber volume content on the mechanical properties, durability, and chloride ion penetration of polypropylene-fiber-reinforced concrete in a chloride environment. Tests were carried out on cubes and cylinders of polypropylene-fiber-reinforced concrete with polypropylene fiber contents ranging from 0% to 0.5%. Extensive data from flexural strength testing, dry–wet testing, deicer frost testing, and chloride penetration testing were recorded and analyzed. The test results show that the addition of the fiber improves the failure form of the concrete specimens, and 0.1% fiber content maximizes the compactness of the concrete. The flexural strength of specimen C2 with 0.1% fiber shows the highest strength obtained herein after freeze–thaw cycling, and the water absorption of specimen C2 is also the lowest after dry–wet cycling. The results also indicate that increasing the fiber volume content improves the freeze–thaw resistance of the concrete in a chloride environment. Chlorine ions migrate with the moisture during dry–wet and freeze–thaw cycling. The chlorine ion diffusion coefficient (Dcl) increases with increasing fiber content, except for that of specimen C2 in a chloride environment. The Dcl during freeze–thaw cycling is much higher than that during dry–wet cycling.

scholarly journals Lightweight SFRC Benefitting from a Pre-Soaking and Internal Curing Process

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4152 ◽  
Author(s):  
Marie Hornakova ◽  
Jacek Katzer ◽  
Janusz Kobaka ◽  
Petr Konecny
Keyword(s):  
Strength Class ◽  
Coarse Aggregate ◽  
Steel Fiber ◽  
Fiber Reinforced Concrete ◽  
Internal Curing ◽  
Fine Aggregate ◽  
Coated Steel ◽  
Curing Process ◽  
Model Code ◽  
Concrete Mix

The presented research program is focused on the design of a structural lightweight fiber-reinforced concrete harnessing an internal curing process. Pre-soaked waste red ceramic fine aggregate and pre-soaked artificial clay expanded coarse aggregate were utilized for the creation of the mix. Copper-coated steel fiber was added to the mix by volume in amounts of 0.0%, 0.5%, 1.0%, and 1.5%. Test specimens in forms of cubes, cylinders, and beams were tested to specify the concrete characteristics. Such properties as consistency, compressive strength, splitting tensile strength, static and dynamic modulus of elasticity, flexural characteristics, and shear strength were of special interest. The achieved concrete can be classified as LC12/13. A strength class, according to fib Model Code, was also assigned to the concretes in question. The proposed method of preparation of concrete mix using only pre-soaked aggregate (with no extra water) proved to be feasible.

Investigation of Critical Quality Assurance Parameter Variations for Concrete

1997 ◽  
Vol 1575 (1) ◽  
pp. 92-101
Author(s):  
Richard K. Smutzer ◽  
Sedat Gulen ◽  
Youlanda K. Belew ◽  
Virgil L. Anderson
Keyword(s):  
High Pressure ◽  
Quality Assurance ◽  
Flexural Strength ◽  
Concrete Strength ◽  
Pulse Velocity ◽  
Hardened Concrete ◽  
Army Corps ◽  
Split Tensile Strength ◽  
Air Content ◽  
Concrete Mix

The Indiana Department of Transportation is involved in preparing statistically sound specifications for strong and durable concrete used in quality assurance programs. Previous laboratory studies relating concrete strength to air content and concrete mix designs dealt with variation in compressive strength. This study searched for a statistically sound relationship between air content, concrete mix designs, and flexural strength. This study also developed a high-pressure method of hardened concrete air content determination. Sixty-four independent batches (combinations) of concrete were produced, each batch was subjected to a total of 24 tests—4 plastic and 20 hardened. The design factors were aggregate type and gradation, plastic air content, cement, and pozzolanic content and testing operator. After plastic testing, three flexural strength beams were cast from each batch of concrete. The experimental design response variables consisted of flexural, compressive, and split tensile strength along with pulse velocity. Analysis of variances, indicated that the optimum flexural strength could be obtained using as-received stone course aggregate and an air content of between 6 percent and 7.9 percent, with no fly ash. A high-pressure air meter, similar to the meter developed by the Army Corps of Engineers, was used. A strong statistical correlation of determination, r2 = 0.94, was obtained between plastic and the hardened concrete air content using this meter.

Experiment Investigation on Mechanical Property of Glass Fiber Reinforced Concrete

2014 ◽  
Vol 915-916 ◽  
pp. 784-787
Author(s):  
Yan Lv
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Volume Fraction ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Glass Fiber Reinforced

Based on the mechanical properties experiment of the glass fiber reinforced concrete with 0%0.6%0.8% and 1% glass fiber volume fraction, the mechanics property such as tensile strength, compressive strength, flexural strength and flexural elasticity modulus are analyzed and compared with the plain concrete when the kinds of fiber content changes. The research results show that the effect of tensile strength and flexural strength can be improved to some extent, which also can serve as a reference or basis for further improvement and development the theory and application of the glass fiber reinforced concrete.

scholarly journals Tests on workability and strength of high strength-flowable concrete containing PET waste fiber

2020 ◽  
Vol 7 (3) ◽  
pp. 115-139
Author(s):  
Sarkawt Karim ◽  
◽  
Azad Mohammed ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Time Increase ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Waste ◽  
Strength Tests

This study describes two workability tests, compressive strength and tensile strength tests of high strength flowable concrete containing plastic fiber prepared from polyethylene terephthalate (PET) waste bottles. For the high fluidity mix Vebe time and V-funnel time tests were carried out. Results show that there is a Vebe time increase with PET fiber addition to concrete being increased with increasing fiber volume and fiber length. V-funnel time was found to reduce when up to 0.75% fiber volume is added to concrete, followed by an increase for larger fiber volumes. When fiber length is increase, there is more time increase, but in general, V-funnel time increase was lower than that of Vebe time, indicating a different influence of PET fiber on the compatibility and flowability. The measured V-funnel time for all mixes was found to conform to the limits of European specifications on the flowability of self compacting concrete. Small descending in compressive strength was recorded for RPET fiber reinforced concrete that reached 15.74 % for 1.5 percent fiber content with 10 mm fiber length. Attractive results was recorded in split tensile strength of RPET fibrous samples which resulted in improvement up to 63.3 % for 1.5 percent of 40 mm fiber length content.

Mechanical and Durability Analysis of Recycled Materials

2021 ◽  
Vol 882 ◽  
pp. 228-236
Author(s):  
Anamika Agnihotri ◽  
Ajay Singh Jethoo ◽  
P.V. Ramana
Keyword(s):  
Research Work ◽  
Waste Glass ◽  
Partial Substitution ◽  
Fine Aggregate ◽  
Split Tensile Strength ◽  
Recycled Materials ◽  
Durability Properties ◽  
Substitution Level ◽  
Durability Analysis ◽  
Concrete Mix

The mechanical and durability properties were best at 45% GGBS and 5% Waste Glass with 0.4 water/cement ratio. The recycled materials implemented for mix proportion were waste glass provided considerably to enhance its properties when added with GGBS. In most of the research work, the effect of WG and GGBS in concrete as a partial substitution of fine aggregate and cement individually is analyzed. Previous studies only show the individual impact of these concrete recycled materials on mechanical and durability properties. In the present study, an exact optimum substitution level of cement by GGBS (15 – 60% at an increment of 15%) and fine aggregate by the waste glass (5 – 20% at an increase of 5%) combined for OPC concrete mix. Mechanical (compressive strength, split tensile strength and flexural strength) and microstructural properties (FESEM) were observed on the combination of waste glass and GGBS concrete mix.

scholarly journals Structural Behavior of Reinforced Concrete Slabs Containing Fine Waste Aggregates of Polyvinyl Chloride

Buildings ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 26
Author(s):  
Nisreen S. Mohammed ◽  
Bashar Abid Hamza ◽  
Najla’a H. AL-Shareef ◽  
Husam H. Hussein
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Waste Materials ◽  
Concrete Slabs ◽  
Fine Aggregate ◽  
Aggregate Concrete ◽  
Flexural Performance ◽  
Reinforced Concrete Slabs ◽  
Concrete Mix

In several areas worldwide, the high cost and shortage of natural resources have encouraged researchers and engineers to explore the serviceability and feasibility of using recycled aggregates in concrete mixtures, substituting a normal aggregate percentage. This technique has advantages for the environment by reducing the accumulation of waste materials, while it impacts the fresh and hardened concrete performances, reducing workability, flexural strength, compressive strength, and tensile strength. However, most studies have investigated the influence of replacing normal aggregates with waste aggregates on the concrete mechanical properties without examining the impact of using waste materials on concrete structural performance. The aim of this research is to investigate the effect of replacing 75% of sand volume with polyvinyl chloride (PVC) fine waste aggregates on the performance of reinforced concrete slabs. Different thicknesses of the concrete layer (0%, 25%, 50%, and 100% of slab thickness) containing PVC fine waste aggregates are investigated. Based on the reductions in the toughness and flexural strength capacity due to incorporating 75% PVC fine aggregate dosage, two approaches are used to strengthen the slabs with 75% PVC fine aggregates. The first approach is adding polyvinyl alcohol (PVA) to the PVC fine aggregate concrete mix to improve the mechanical properties of the concrete. The PVA increases the water viscosity in the concrete, which reduces the dry out phenomenon. With that said, the PVA modified fresh concrete does enable the use of the limits of the PVC fine aggregate dosage for high dosage plastic aggregate concrete. The second approach uses two fiber wire mesh layers as an additional reinforcement in the tested slab. Results show that the PVC-30 slab exhibits an 8% decrease in total area toughness compared to the control (Con) slab, while for PVC-60 slab toughness, the total area shows 26% less. Additionally, the inclusion of PVA in the concrete with 75% PVC plastic waste fine aggregate replacement greatly influences the pre-and post-cracking ductile performance among other slabs, representing that using PVA with higher contents might increase the flexural performance. Therefore, due to the substantial effect of PVA material on the concrete flexural performance, it is proposed to utilize PVA with an optimum PCV fine aggregate dosage in the concrete mix.

scholarly journals ANALISIS KUAT TARIK BELAH TERHADAP PEMANFAATAN LIMBAH STRAPPING BAND SEBAGAI SUBSTITUSI PASIR PADA BETON NORMAL

2020 ◽  
Vol 13 (2) ◽  
pp. 137
Author(s):  
Dr. Akhmad Suryadi, BS., MT
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Reinforced Concrete ◽  
Concrete Mixture ◽  
Synthetic Fiber ◽  
Average Weight ◽  
Fine Aggregate ◽  
Split Tensile Strength ◽  
Tensile Strength Test ◽  
Concrete Concept

The advancement era, the use of strapping band in the process of shipping goods was increases because of the more practical needs and stronger straps make the waste from strapping band was increases. With a large amount of waste by shredding it into smaller sizes it can be used as a substitute for fine aggregate in concrete mixture with synthetic fiber reinforced concrete concept at the Laboratory of Civil Engineering Politeknik Negeri Malang. The objectives of this research were to analyze the characteristics of concrete with the substitution of strapping band waste against fine aggregate in compressive strength and split tensile strength test. The research method including: aggregate test and strapping band test, the mix design of concrete mixture was using the reference SNI 03-2834-2000. The experiments sample for each variation of 0%, 5%, and 8% were performed with 24 cylinder specimens for compressive strength and 6 cylinder specimens for split tensile strength. The compressive strength on 28 days with 0%, 5%, and 8% variation resulted in 27.67 kg/cm2; 26.82 kg/cm2; 17.83 kg/cm2. The split tensile strength on 28 days with 0% 5%, and 8% variation resulted in 2.42 kg/cm2; 1.90 kg/cm2; 1.51 kg/cm2. The average weight of cylinder specimens with 0%, 5%, and 8% variation resulted in 12.62 kg; 12.04 kg; 11.61 kg. Substitution of strapping band waste decreases compressive strength, split tensile strength and average weight concrete. Key words : Strapping band waste, compressive strength, split tensile strength

scholarly journals Evaluation of Interlocking Brick

2021 ◽  
Vol 9 (8) ◽  
pp. 3002-3008
Author(s):  
C. Mounika
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Crumb Rubber ◽  
Strength Test ◽  
Fine Aggregate ◽  
Coir Fiber ◽  
Split Tensile Strength ◽  
Rubber Tire

Abstract: The main aim of this project is to evaluate mechanical properties of interlocking bricks using coir fiber powder as a substitute of cement and rubber tire waste as a substitute of fine aggregate (sand) with varying percentages of 0%, 1%, 2% & 3% and 0%, 5%, 10% & 15% in concrete and to help in solving environmental problem produced from disposing of waste tires and coir husk partially. Additionally fly ash was also added with varying percentages of 5%, 10% and 15% as a substitute to cement in a concrete mix. Several laboratory tests such as compressive strength test, flexural strength test, split tensile strength test, water absorption test and density of concrete etc., were conducted on hardened concrete specimen to achieve the optimum usage of crumb rubber tire waste and coir fiber powder in mix proportion of concrete. It is found that the maximum compressive strength value of coir fiber based crumb rubber interlocking brick was obtained at 1%CF + 5%FA + 5%CR, flexural strength value and split tensile strength value of coir fiber based crumb rubber concrete block was obtained at 1%CF + 5%FA + 5%CR. From the final conclusion or outcome of the project, optimum usage of coir fiber powder is 3% and crumb rubber is 5%. Keywords: coir fiber powder, crumb rubber tire waste, mechanical properties, interlocking bricks & optimum usage.

Relationship between Compressive, Splitting Tensile and Flexural Strength of Concrete Containing Granulated Waste Polyethylene Terephthalate (PET) Bottles as Fine Aggregate

2013 ◽  
Vol 795 ◽  
pp. 356-359 ◽  
Author(s):  
Mohd Irwan Juki ◽  
Mazni Awang ◽  
Mahamad Mohd Khairil Annas ◽  
Koh Heng Boon ◽  
Norzila Othman ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Fine Aggregate ◽  
Pet Bottles ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Waste Polyethylene

This paper describes the experimental investigation of relationship between splitting tensile strength and flexural strength with the compressive strength of concrete containing waste PET as fine aggregates replacement. Waste PET was reprocesses and used as the artificial fine aggregate at the replacement volume of 25%, 50% and 75%, Cylindrical and prism specimens were tested to obtain the compressive, splitting tensile and flexural strength at the age of 28 days. Based on the investigation, a relationship for the prediction of splitting tensile and flexural strength was derived from the compressive strength of concrete containing waste PET as fine agglegate replacement.

Sign in / Sign up

Export Citation Format

Share Document