scholarly journals In-Situ Ultrasound-Assisted Control of Polymeric Membrane Fouling

2021 ◽  
Author(s):  
Westphalen Dornelas Camara Heloisa
Keyword(s):  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Separation ◽  
Feed Solution ◽  
Solution Concentration ◽  
Polymeric Membrane ◽  
Permeate Flux ◽  
Latex Paint ◽  
Water And Wastewater Treatment ◽  
Maximum Increase

Membrane separation processes have been more widely applied to industrial activities, especially in water and wastewater treatment. However, there are still challenges associated to the use of membranes. Concentration polarization and fouling can cause significant permeate flux decay during the filtration process, hindering its efficiency and increasing cost. Among many strategies, the combination of membrane filtration with ultrasound (US) application has shown promising results in reducing membrane fouling. The main goal of this research was to identify the effect of US frequency, US power intensity and feed solution concentration on permeate flux during ultrafiltration of simulated latex paint effluent. Maximum increase in permeate flux of 19.7% was obtained by applying 20 kHz and 0.29 W.cm-2 to feed solution with 0.075 wt.% of solid concentration. The effect of feed flow rate was analyzed showing that an increase in feed flowrate is not beneficial to the fouling minimization process. Overall, the application of US improves permeate flux by reducing fouling of ultrafiltration polymeric membrane.

scholarly journals In-Situ Ultrasound-Assisted Control of Polymeric Membrane Fouling

2021 ◽  
Author(s):  
Westphalen Dornelas Camara Heloisa
Keyword(s):  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Separation ◽  
Feed Solution ◽  
Solution Concentration ◽  
Polymeric Membrane ◽  
Permeate Flux ◽  
Latex Paint ◽  
Water And Wastewater Treatment ◽  
Maximum Increase

Membrane separation processes have been more widely applied to industrial activities, especially in water and wastewater treatment. However, there are still challenges associated to the use of membranes. Concentration polarization and fouling can cause significant permeate flux decay during the filtration process, hindering its efficiency and increasing cost. Among many strategies, the combination of membrane filtration with ultrasound (US) application has shown promising results in reducing membrane fouling. The main goal of this research was to identify the effect of US frequency, US power intensity and feed solution concentration on permeate flux during ultrafiltration of simulated latex paint effluent. Maximum increase in permeate flux of 19.7% was obtained by applying 20 kHz and 0.29 W.cm-2 to feed solution with 0.075 wt.% of solid concentration. The effect of feed flow rate was analyzed showing that an increase in feed flowrate is not beneficial to the fouling minimization process. Overall, the application of US improves permeate flux by reducing fouling of ultrafiltration polymeric membrane.

scholarly journals Assessing Enzyme Immobilization on Reverse Asymmetric Membranes and Biocatalytic Reactor Performance

2021 ◽  
Author(s):  
Amirah Syakirah Zahirulain ◽  
Fauziah Marpani ◽  
Syazana Mohamad Pauzi ◽  
'Azzah Nazihah Che Abd Rahim ◽  
Hang Thi Thuy Cao ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Separation ◽  
Permeate Flux ◽  
Reactor Performance ◽  
Membrane Performance ◽  
Reverse Mode ◽  
Substrate Conversion ◽  
Product Separation

Abstract Integration of membrane filtration and biocatalysis has appealing benefits in terms of simultaneous substrate conversion and product separation in one reactor. Nevertheless, the interaction between enzymes and membrane is complex and the mechanism of enzyme docking on membrane is similar to membrane fouling. In this study, focus is given on the assessment of enzyme immobilization mechanism on reverse asymmetric polymer membrane based on the permeate flux data during the procedure. Evaluation of membrane performance in terms of its permeability, fouling mechanisms, enzyme loading, enzyme reusability and biocatalytic productivity were also conducted. Alcohol Dehydrogenase (EC 1.1.1.1), able to catalyze formaldehyde to methanol with subsequent oxidation of NADH to NAD was selected as the model enzyme. Two commercial, asymmetric, flat sheet polymer membranes (PES and PVDF) were immobilized with the enzyme in the reverse mode. Combination of concentration polarization phenomenon and pressure driven filtration successfully immobilized almost 100% of the enzymes in the feed solutions. The biocatalytic membrane reactor recorded more than 90% conversion, stable permeate flux with no enzyme leaching even after 5 cycles. The technique showing promising results to be expanded to continuous membrane separation setup for repeated use of enzymes.

scholarly journals Effect of Pre-Oxidation on Coagulation/Ceramic Membrane Treatment of Yangtze River Water

Membranes ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 369
Author(s):  
Shengji Xia ◽  
Xinran Zhang ◽  
Yuanchen Zhao ◽  
Fibor J. Tan ◽  
Pan Li ◽  
...  
Keyword(s):  
Water Treatment ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Ceramic Membrane ◽  
Membrane Separation ◽  
Membrane System ◽  
Coagulation System ◽  
Fouling Control ◽  
Filtration System ◽  
Membrane Treatment

The membrane separation process is being widely used in water treatment. It is very important to control membrane fouling in the process of water treatment. This study was conducted to evaluate the efficiency of a pre-oxidation-coagulation flat ceramic membrane filtration process using different oxidant types and dosages in water treatment and membrane fouling control. The results showed that under suitable concentration conditions, the effect on membrane fouling control of a NaClO pre-oxidation combined with a coagulation/ceramic membrane system was better than that of an O3 system. The oxidation process changed the structure of pollutants, reduced the pollution load and enhanced the coagulation process in a pre-oxidation-coagulation system as well. The influence of the oxidant on the filtration system was related to its oxidizability and other characteristics. NaClO and O3 performed more efficiently than KMnO4. NaClO was more conducive to the removal of DOC, and O3 was more conducive to the removal of UV254.

scholarly journals Organic Fouling Impact in a Direct Contact Membrane Distillation System Treating Wastewater: Experimental Observations and Modeling Approach

Membranes ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 493
Author(s):  
Amine Charfi ◽  
Fida Tibi ◽  
Jeonghwan Kim ◽  
Jin Hur ◽  
Jinwoo Cho
Keyword(s):  
Particle Size ◽  
Membrane Fouling ◽  
Direct Contact ◽  
Feed Solution ◽  
Membrane Distillation ◽  
Mixed Solution ◽  
Permeate Flux ◽  
Direct Contact Membrane Distillation ◽  
Organic Fouling ◽  
Specific Cake Resistance

This study aims to investigate the effect of operational conditions on organic fouling occurring in a direct contact membrane distillation (DCMD) system used to treat wastewater. A mixed solution of sodium alginate (SA) and bovine serum albumin (BSA) was used as a feed solution to simulate polysaccharides and proteins, respectively, assumed as the main organic foulants. The permeate flux was observed at two feed temperatures 35 and 50 °C, as well as three feed solution pH 4, 6, and 8. Higher permeate flux was observed for higher feed temperature, which allows higher vapor pressure. At higher pH, a smaller particle size was detected with lower permeate flux. A mathematical model based on mass balance was developed to simulate permeate flux with time by assuming (i) the cake formation controlled by attachment and detachment of foulant materials and (ii) the increase in specific cake resistance, the function of the cake porosity, as the main mechanisms controlling membrane fouling to investigate the fouling mechanism responsible of permeate flux decline. The model fitted well with the experimental data with R2 superior to 0.9. High specific cake resistance fostered by small particle size would be responsible for the low permeate flux observed at pH 8.

A Wall Film Model for Membrane Fouling

2018 ◽  
Author(s):  
Sina Jahangiri Mamouri ◽  
Volodymyr V. Tarabara ◽  
André Bénard
Keyword(s):  
Multiphase Flow ◽  
Membrane Fouling ◽  
Oil And Gas ◽  
Membrane Separation ◽  
Film Formation ◽  
Membrane Surface ◽  
Permeate Flux ◽  
Water Separation ◽  
Wall Film ◽  
Oil Water

Deoiling of produced or impaired waters associated with oil and gas production represents a significant challenge for many companies. Centrifugation, air flotation, and hydrocyclone separation are the current methods of oil removal from produced water [1], however the efficiency of these methods decreases dramatically for droplets smaller than approximately 15–20 μm. More effective separation of oil-water mixtures into water and oil phases has the potential to both decrease the environmental footprint of the oil and gas industry and improve human well-being in regions such as the Gulf of Mexico. New membrane separation processes and design of systems with advanced flow management offer tremendous potential for improving oil-water separation efficacy. However, fouling is a major challenge in membrane separation [2]. In this study, the behavior of oil droplets and their interaction with crossflow filtration (CFF) membranes (including membrane fouling) is studied using computational fluid dynamics (CFD) simulations. A model for film formation on a membrane surface is proposed for the first time to simulate film formation on membrane surfaces. The bulk multiphase flow is modeled using an Eulerian-Eulerian multiphase flow model. A wall film is developed from mass and momentum balances [3] and implemented to model droplet deposition and membrane surface blockage. The model is used to predict film formation and subsequent membrane fouling, and allow to estimate the actual permeate flux. The results are validated using available experimental data.

scholarly journals Effect of pH on membrane fouling during alcohol dehydrogenase immobilization in PES membrane

2020 ◽  
Vol 3 (2) ◽  
pp. 30
Author(s):  
Nurshahira Hazwani Hamran ◽  
Fauziah Marpani ◽  
Nur Hidayati Othman ◽  
Nik Raikhan Nik Him ◽  
Nur Hashimah Alias ◽  
...  
Keyword(s):  
Alcohol Dehydrogenase ◽  
Enzyme Immobilization ◽  
Membrane Fouling ◽  
Feed Solution ◽  
Permeate Flux ◽  
Enzyme Loading ◽  
Solution Ph ◽  
Observed Rejection ◽  
Pes Membrane ◽  
Blocking Mechanism

Fouling-induced enzyme immobilization is a technique to immobilize enzyme by positively manipulating the knowledge of membrane fouling. In this study, Alcohol dehydrogenase (ADH) (EC 1.1.1.1) was immobilized in the support layer of ultrafiltration PES membrane at different solution pH (acid, neutral and alkaline). ADH catalyses formaldehyde (CHOH) to methanol (CH3OH) and simultaneously oxidised nicotinamide adenine dinucleotide (NADH) to NAD+. The initial feed amount of enzyme is 3.0 mg. The objective of the study aims at the effect of different pH of feed solution during enzyme immobilization, in terms of permeate flux, observed rejection, enzyme loading and fouling mechanism. The results showed that, pH 5 holds the highest enzyme loading which is 65% while pH 7 holds the lowest at 52% out of 3.0 mg as the initial enzyme feed. The permeate flux for each pH decreased with increasing cumulative permeate volume. The observed rejection is inversely correlated with the pH where increase in pH will cause a lower observed rejection. The fouling model predicted that irreversible fouling occurs during enzyme immobilization at pH 7 with standard blocking mechanism while reversible fouling occurs at pH 5 and 9 with intermediate and complete blocking, respectively.

scholarly journals Low- and High-Pressure Membrane Separation in the Production of Process Water for Coke Quenching

Membranes ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 937
Author(s):  
Anna Trusek ◽  
Maciej Wajsprych ◽  
Andrzej Noworyta
Keyword(s):  
High Pressure ◽  
Membrane Filtration ◽  
Membrane Separation ◽  
Coke Oven ◽  
Industrial Plant ◽  
Operating Pressure ◽  
Permeate Flux ◽  
Final Treatment ◽  
Stage System ◽  
Pressure Plant

Although the time for operating mines and coking plants in many countries is coming to an end due to climate change, we must still ensure that the pollution generated by this source of the economy is minimized. Despite the several stages of treatment of the coke-oven effluent, completed with nitrification and denitrification processes preceding final sedimentation, the stream obtained does not meet the requirements of water for coke quenching. That is why the stream after biodegradation and sedimentation was treated on membrane units to ensure water reusing in the coking plant. As the subjected stream contained both solid and dissolved pollutants, a two-stage system was proposed: low- and high-pressure membrane filtration. Industrial modules were tested on pilot units operating under industrial plant conditions. In the case of the ultrafiltration process, all the tested ultrafiltration modules fulfilled the primary task. All of them separated almost completely the turbidities present in the stream, which would have disturbed the operation of the high-pressure plant. Considering the decrease in permeate flux and the possibility of cleaning, a PCI membrane made of PVDF tubes with a diameter of 12.5 mm and pore size of 20 μm was selected. Regarding the high-pressure membrane filtration, the reverse osmosis membrane was significantly better in the removal efficiency of both organic and inorganic dissolved substances. An operating pressure of 3 MPa was chosen for the system. Hence, membrane processes, which are not used as stand-alone treatment units for coke-oven effluents, function well as a final treatment stage.

scholarly journals Hybrid System Coupling Moving Bed Bioreactor with UV/O3 Oxidation and Membrane Separation Units for Treatment of Industrial Laundry Wastewater

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2648
Author(s):  
Sylwia Mozia ◽  
Magdalena Janus ◽  
Sławomira Bering ◽  
Krzysztof Tarnowski ◽  
Jacek Mazur ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Separation ◽  
Oxygen Demand ◽  
Membrane System ◽  
Permeate Flux ◽  
Moving Bed ◽  
System A ◽  
Water Recycle ◽  
Recycle And Reuse ◽  
System Coupling

This paper describes the investigations on the possibilities of treatment of wastewater generated in an industrial laundry with application of a combined biological-photooxidation- membrane system aimed at water recycle and reuse. The two treatment schemes were compared: 1) scheme A consisting of a treatment in a moving bed biological reactor (MBBR) followed by microfiltration (MF) and nanofiltration (NF), and 2) scheme B comprising MBBR followed by oxidation by photolysis enhanced with in situ generated O3 (UV/O3) after which MF and NF were applied. The removal efficiency in MBBR reached 95–97% for the biochemical oxygen demand; 90–93% for the chemical oxygen demand and 89–99% for an anionic and a nonionic surfactants. The application of UV/O3 system allowed to decrease the content of the total organic carbon by 68% after 36 h of operation with a mineralization rate of 0.36 mg/L·h. Due to UV/O3 pretreatment, a significant mitigation of membrane fouling in the case of both MF and NF processes was achieved. The MF permeate flux in the system B was over two times higher compared to that in the system A. Based on the obtained results it was concluded that the laundry wastewater pretreated in the MBBR-UV/O3-MF-NF system could be recycled to any stage of the laundry process.

The Effect of Flow Pulsation on Ultrafiltration System Limiting Flux Behavior

2013 ◽  
Author(s):  
Chyouhwu Brian Huang ◽  
Hung-Shyong Chen
Keyword(s):  
Membrane Filtration ◽  
Concentration Polarization ◽  
Membrane Separation ◽  
Membrane Surface ◽  
Paper Industry ◽  
Surface Concentration ◽  
Permeate Flux ◽  
Filtration Time ◽  
Protection Systems ◽  
Oil Water

Ultrafiltration (UF) is an important industrial operation and is found in the food industry, separation of oil-water emulsions, treatment effluents from the pulp and paper industry, and environmental protection systems. Despite being widely used in these areas, UF systems exhibit a limiting flux behavior caused by concentration polarization on the membrane surface. Concentration polarization can be severe in macromolecular solutions due to low diffusivity on membrane separation and both mechanical and chemical methods have been used to reduce this phenomenon. This study introduces a new mechanical method that improves the performance of membrane separation and decreases concentration polarization. It involves pulsing the feed flow discontinuously and based on our results, feed flow velocity and solution bypass/membrane filtration time ratio are two vital factors when it comes to improving permeate flux. The proposed method is expected to find wide application, particularly in the processing of macromolecular solution.

A review on membrane applications and transport mechanisms in vacuum membrane distillation

2017 ◽  
Vol 34 (1) ◽  
Author(s):  
Rakesh Baghel ◽  
Sushant Upadhyaya ◽  
Kailash Singh ◽  
Satyendra P. Chaurasia ◽  
Akhilendra B. Gupta ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Separation ◽  
Critical Evaluation ◽  
Experimental Studies ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Separation Processes ◽  
Vacuum Membrane Distillation ◽  
Polarization Coefficient ◽  
The Impact

AbstractThe main aim of this article is to provide a state-of-the-art review of the experimental studies on vacuum membrane distillation (VMD) process. An introduction to the history of VMD is carried out along with the other membrane distillation configurations. Recent developments in process, characterization of membrane, module design, transport phenomena, and effect of operating parameters on permeate flux are discussed for VMD in detail. Several heat and mass transfer correlations obtained by various researchers for different VMD modules have been discussed. The impact of membrane fouling with its control in VMD is discussed in detail. In this paper, temperature polarization coefficient and concentration polarization coefficient are elaborated in detail. Integration of VMD with other membrane separation processes/industrial processes have been explained to improve the performance of the system and make it more energy efficient. A critical evaluation of the VMD literature is incorporated throughout this review.

Sign in / Sign up

Export Citation Format

Share Document