scholarly journals Effect of Sand Fouling on the Dynamic Properties and Volume Change of Gravel During Cyclic Loadings

2020 ◽  
Author(s):  
Meysam Bayat
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Dynamic Behavior ◽  
Volume Change ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Practical Applications ◽  
Large Shear Strain

Understanding the factors that influence the dynamic behavior of granular soils during cyclic loading is critical to infrastructure design. Previous research has lacked quantitative study of the effects of fouling index (FI), mean effective confining pressure, relative density, shear strain level and anisotropic consolidation, especially when the effective vertical stress is lower than the effective horizontal stress on the dynamic behavior of gravelly soils. The objective of the present study was to evaluate the dynamic behavior and volume change of both clean and fouled specimens for practical applications. To this end, cyclic triaxial tests with local strain measurements under both isotropic and anisotropic confining conditions were conducted. It is found that the fouled specimen with 50 % sand (i.e. the specimen which contains 50 % gravel and 50 % sand) has the highest shear modulus at low shear strain levels and the largest volume reduction and damping ratio at large shear strain levels. The results of tests indicate that the effect of fouling index on the shear modulus is reduced at large shear strain levels. Volumetric contraction due to the increase in mean effective confining pressure is more significant at large shear strain levels. The results also indicate that the stiffness of the specimens under anisotropic compression mode are larger than those in extension or isotropic mode.

scholarly journals Dynamic Properties of Sand-Sawdust Mixture for Modeling Deposit Soil

2019 ◽  
Vol 9 (18) ◽  
pp. 3863
Author(s):  
Pan ◽  
Li ◽  
Lu ◽  
Chen
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Shaking Table Test ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Strain Range ◽  
Confining Pressure ◽  
Shaking Table ◽  
Triaxial Tests ◽  
Hysteresis Curve

Soil mixtures with various materials such as scraps of rubber tire, iron powder, and synthetic fibers have been widely used in civil engineering for experimental research or infrastructure construction and maintenance. However, these materials are not only expensive, but may also result in environmental concerns. In recent years, sawdust, because of its light-weight, inexpensive, and environmental friendly characteristics, has frequently been used in the shaking table test to adjust the dynamic properties of experimental soil. However, the dynamic properties of a sand-sawdust mixture for the shaking table test are still unclear. In this paper, the dynamic properties and the hysteresis curve characteristics of the sand-sawdust mixture as well as the influence of the sawdust content and confining pressure on the dynamic properties were studied using a series of consolidated drained dynamic triaxial tests. The test results show that, with the increase of the shear strain, the shape of the hysteresis loops changes from symmetrical willow-leaf to asymmetry sharp-leaf. For a given confining pressure, both the shear modulus and damping ratio decreases as the sawdust percentage increases. It was observed that, with an increase in confining pressure, the shear modulus increased while the damping ratio decreased slightly in the shear strain range of 10−3 to 7×10−3. It was also observed that the maximum shear modulus increased as the confining pressure increased, while the maximum damping ratio remained nearly constant. In addition, both the maximum shear modulus and the maximum damping ratio decreased as the sawdust content increased. Finally, the normalized shear modulus and damping ratio were established, which can be used in simulations using the shaking table test.

scholarly journals Characterization of the Dynamic Properties of Clay–Gravel Mixtures at Low Strain Level

2020 ◽  
Vol 12 (4) ◽  
pp. 1616 ◽  
Author(s):  
Xianwen Huang ◽  
Aizhao Zhou ◽  
Wei Wang ◽  
Pengming Jiang
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Mechanical Performance ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Strain Level ◽  
Dynamic Shear Modulus ◽  
Dynamic Shear ◽  
Gravel Content

In order to support the dynamic design of subgrade filling engineering, an experiment on the dynamic shear modulus (G) and damping ratio (D) of clay–gravel mixtures (CGMs) was carried out. Forty-two groups of resonant column tests were conducted to explore the effects of gravel content (0%, 10%, 20%, 30%, 40%, 50%, and 60%, which was the mass ratio of gravel to clay), gravel shape (round and angular gravels), and confining pressure (100, 200, and 300 kPa) on the dynamic shear modulus, and damping ratio of CGMs under the same compacting power. The test results showed that, with the increase of gravel content, the maximum dynamic shear modulus of CGMs increases, the referent shear strain increases linearly, and the minimum and maximum damping ratios decrease gradually. In CGMs with round gravels, the maximum dynamic shear modulus and the maximum damping ratio are greater, and the referent shear strain and the minimum damping ratio are smaller, compared to those with angular gravels. With the increase of confining pressure, the maximum dynamic shear modulus and the referent shear strain increase nonlinearly, while the minimum and maximum damping ratios decrease nonlinearly. The predicting equation for the dynamic shear modulus and the damping ratio of CGMs when considering confining pressure, gravel content, and shape was established. The results of this research may put forward a solid foundation for engineering design considering low-strain-level mechanical performance.

DEGRADATION EFFECT OF SEAWATER ON THE LONG-TERM DYNAMIC BEHAVIOR OF ARTIFICIALLY CEMENTED SAND

2013 ◽  
Vol 07 (04) ◽  
pp. 1350031 ◽  
Author(s):  
BO LI ◽  
YUANQIANG CAI ◽  
XIANGWU ZENG ◽  
LINYOU PAN
Keyword(s):  
Shear Modulus ◽  
Dynamic Behavior ◽  
Tap Water ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Resonant Column ◽  
Cyclic Triaxial Tests ◽  
Cemented Sand

The dynamic behavior of lightly cemented sand under long-term seawater attack was evaluated in this study. Resonant column and cyclic triaxial tests were employed to investigate the evolution of the shear modulus and damping ratio of cemented sand with respect to soaking period (SP), confining pressure, and cement content (CC). The results of this study show that the cementation of the sand is affected by soaking in seawater to a greater extent than by soaking in tap water. The shear modulus of the cemented sand soaked in seawater was smaller than that of the cemented sand soaked in tap water. The damping ratio increased significantly, as the SP increased and was greater for the cemented sand soaked in seawater than for the cemented sand soaked in tap water. The dynamic behavior of nonhomogenous specimens was examined. Crystallization of salts could be clearly observed and probably explains the evolution of the dynamic behavior of the cemented sand. Finally, the shear modulus was fitted using Rollins' Law [Rollins et al., 1998], which demonstrates that the parameters used in the equation can be reasonably fitted linearly over a range of SPs.

scholarly journals Laboratory Characterization of a Compacted–Unsaturated Silty Sand with Special Attention to Dynamic Behavior

2020 ◽  
Vol 10 (7) ◽  
pp. 2559
Author(s):  
Andrzej Głuchowski ◽  
Zdzisław Skutnik ◽  
Marcin Biliniak ◽  
Wojciech Sas ◽  
Diego Lo Presti
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Silty Sand ◽  
Triaxial Tests ◽  
Bender Element ◽  
State Dependent ◽  
Laboratory Characterization ◽  
Dynamic Excitations

The dynamic properties of compacted non-cohesive soils are desired not only because of the risk of natural sources of dynamic excitations such as earthquakes, but mostly because of the anthropogenic impact of machines that are working on such soils. These soils are often unsaturated, which positively affects the soil’s mechanical properties. The information about the values of these parameters is highly desirable for engineers. In this article, we performed a series of tests, including oedometric tests, resonant column tests, bender element tests, and unsaturated triaxial tests, to evaluate those characteristic parameters. The results showed that sandy silt soil has a typical reaction to dynamic loading in terms of shear modulus degradation and the damping ratio curves’ characteristics, which can be modeled by using empirical equations. We found that the compaction procedure caused an over-consolidation state dependent on the moisture content during compaction effort. The article analyzed the soil properties that impact the maximum shear modulus G0 value. Those properties were suction s, confining pressure σ3, and compaction degree represented by the void ratio function f(e).

scholarly journals Effects of granular shape on shear modulus and damping ratio of gravel

2019 ◽  
Vol 23 (1) ◽  
pp. 87-91
Author(s):  
Kai Cui ◽  
Hang Sheng
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Strain Amplitude ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Test Results ◽  
Grain Composition ◽  
Confining Pressures ◽  
Shear Strain Amplitude

The effects of the consolidation ratio, effective confining pressure, gravel content, and granule breakage on the shear modulus and damping ratio of gravel have been extensively researched in recent years. However, studies on the effect of the granular shape are rare. Thus, under different confining pressures, dynamic triaxial tests were performed on gravel specimens to investigate the effect of granular shape on the shear modulus and damping ratio of gravel specimens by using a multifunctional triaxial testing instrument. The samples consisted of two kinds of gravel with the same grain composition and relative density of 45%. The test results indicate that, when the confining pressure and shear strain amplitude exceed 300 kPa and 7×10-4, respectively, gravel with a round granular shape has a higher shear modulus compared to an angular shape. Conversely, when the shear strain amplitude exceeds 2×10-4, the damping ratio of angular gravel exceeds that of round granules.

Shear Modulus and Damping Ratio of Gravel Material

2011 ◽  
Vol 105-107 ◽  
pp. 1426-1432 ◽  
Author(s):  
De Gao Zou ◽  
Tao Gong ◽  
Jing Mao Liu ◽  
Xian Jing Kong
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Strain Amplitude ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Dynamic Shear Modulus ◽  
Test Results ◽  
Dynamic Shear ◽  
Data Points ◽  
Shear Strain Amplitude

Two of the most important parameters in dynamic analysis involving soils are the dynamic shear modulus and the damping ratio. In this study, a series of tests were performed on gravels. For comparison, some other tests carried out by other researchers were also collected. The test results show that normalized shear modulus and damping ratio vary with the shear strain amplitude, (1) normalized shear modulus decreases with the increase of dynamic shear strain amplitude, and as the confining pressure increases, the test data points move from the low end toward the high end; (2) damping ratio increases with the increase of shear strain amplitude, damping ratio is dependent on confining pressure where an increase in confining pressure decreased damping ratio. According to the test results, a reference formula is proposed to evaluate the maximum dynamic shear modulus, the best-fit curve and standard deviation bounds for the range of data points are also proposed.

Experimental Study on Dynamic Characteristics of Ionic Soil Stabilizer Reinforcing Red Clay

2011 ◽  
Vol 374-377 ◽  
pp. 1391-1395
Author(s):  
Xue Song Lu ◽  
Wei Xiang
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Dynamic Condition ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Natural Soil ◽  
Dynamic Shear Modulus ◽  
Dynamic Shear ◽  
Red Clay ◽  
Soil Stabilizer

Based on the red clay of Wuhan reinforced by Ionic Soil Stabilizer, the red clay soil is treated by different matches of ISS at first, then is tested in the Atterberg limits test and dynamic triaxia test. The results show that the plastic index decreases, and the red clay were greatly improved under the dynamic condition, the maximum dynamic shear modulus ratio acquired an incensement of 27.72% on average after mixing the ISS into the red clay. In addition, It was concluded that the confining pressure influenced the dynamic shear modulus and damping ratio to a certain extent. Given the same strain conditions, with the incensement of confining pressure increases, the dynamic shear modulus increased and the damping ratio decreased. Moreover, when plotting the dynamic shear modulus versus the dynamic shear strain, the similar curve can be formed for both the natural soil and the modified one, the dynamic shear modulus monotonously decreased with the incensement of the dynamic shear strain. However, the value of dynamic shear modulus differed in the same shear strain between the natural soil and the soil modified by ISS.

A Study on Dynamic Properties of Cement-Stabilized Soils

2011 ◽  
Vol 243-249 ◽  
pp. 2050-2054 ◽  
Author(s):  
Pei Hsun Tsai ◽  
Sheng Huoo Ni
Keyword(s):  
Shear Modulus ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Test Results ◽  
Resonant Column Test ◽  
Stabilized Soil ◽  
Shearing Strain ◽  
Relationship Of ◽  
The Relationship

In this paper the dynamic property (shear modulus and damping ratio) of cement-stabilized soil is studied with using the resonant column test. The amount of cement admixed, the magnitude of confining pressure, and shearing strain amplitude are the parameters considered. Test results show that the maximum shear modulus of cement-stabilized soil increases with increasing confining pressure, the minimum damping ratio decreases with increasing confining pressure. The shear modulus of cement-stabilized soil decreases with increasing shearing strain while the damping ratio increases with increasing shearing strain. In the paper the relationship of shear modulus versus shearing strain is fitted into the Ramberg-Osgood equations using regression analysis.

scholarly journals Shear modulus and damping ratio of a nonplastic silt at large shear strains

2019 ◽  
Vol 92 ◽  
pp. 08007
Author(s):  
Alper Sezer ◽  
Eyyub Karakan ◽  
Nazar Tanrinian
Keyword(s):  
Shear Modulus ◽  
Relative Density ◽  
Shear Strain ◽  
Stress Ratio ◽  
Damping Ratio ◽  
Cyclic Stress ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Cyclic Stress Ratio

Site response analyses and solution of dynamic soil-structure interaction problems need determination of variation of shear modulus and damping ratio with shear strain. Since many studies in literature concern evaluation of behavior of sands and silty sands, a series of cyclic triaxial tests were performed to determine the variation of shear modulus and damping ratio of a nonplastic silt with shear strain. Stress controlled cyclic triaxial tests on silt specimens of initial relative densities ranging among 30%, 50% and 70% were performed. Tests were carried out on identical samples under different CSR levels, and the confining pressure was selected as 100 kPa. Variation of shear modulus and damping ratio of silts with cyclic stress ratio amplitude, relative density and number of cycles were investigated. It was understood that soil relative density and cyclic stress ratio amplitude has a significant influence on shear modulus and damping ratio of silts. It was also observed that, as the cyclic stress ratio amplitude is increased, greater shear modulus and lower damping ratio values were obtained.

Dynamic Experimental Study on Highly Weathered Granite

2014 ◽  
Vol 518 ◽  
pp. 132-137
Author(s):  
Lei Niu ◽  
Quan Jie Song ◽  
Shuang Xu ◽  
Xiao Ming Guo
Keyword(s):  
Shear Modulus ◽  
Shear Strain ◽  
Pore Water ◽  
Effective Stress ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Damping Ratio ◽  
Confining Pressure ◽  
Response Analysis ◽  
Weathered Granite

The shear modulus and damping ratio are two important index in equivalent nonlinear model which is widely used in seismic response analysis. GDS resonant-column is used to study the shear modulus and damping ratio of highly weathered granite by controlling the consolidation confining pressure and pore water pressure. Variation of resonant frequency, shear modulus and damping ratio can be observed when different effective stress which is changed with confining pressure and pore water pressure applied on the sample. Hadin-Drnevich fitting curves are given on the basis of experimental data, and damping mechanism of highly weathered granite is discussed by making use of frictional theory. We can conclude from the results that there is a positive correlation between resonance frequency and shear strain, while there is a negative correlation between samples damping ratio and shear strain. The effective stress impact both samples shear modulus and damping ratio. However, pore water pressure can only act on damping ratio.

Sign in / Sign up

Export Citation Format

Share Document