scholarly journals PENGARUH PENAMBAHAN SERAT KULIT PINANG DAN SERBUK KAYU TERHADAP KUAT TARIK BELAH BETON (Kajian Terhadap Ukuran Agregat Maksimal 10 mm)

2019 ◽  
Vol 9 (1) ◽  
pp. 15-22
Author(s):  
Era Rizky Hasanah ◽  
Agustin Gunawan ◽  
Yuzuar Afrizal
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Test Specimen ◽  
Strength Test ◽  
Wood Powder ◽  
Normal Concrete ◽  
High Compressive Strength ◽  
Tensile Strength Test

Concrete has a high compressive strength, but it is low to tensile strength. The pinang skin fiber and wood powderuse to increase the tensile strength. The purpose of this research is to know the effect of addition toward tensile strength and addition percentage variation in concrete that will get the highest tensile strength.The cylindrical specimens with size of 30 cm high and 15 cm diameter to 20 specimens, they are 4 sample of normal concrete and 16 sample of variation oncrete. The addition of pinang skin fiber and wood powder with variation of 0.25%, 0.5%, 0.75%, and 1% of the weight volume of the specimen with used 50% pinang skin fiber and 50% wood powder.The mixture of concrete uses water cement ratioof 0.5 and 60-100 mm slump.The test specimen is immersed for 26 days and the concrete tensile strength test conducted after the concrete at 28 days adding 7 days for drying.The result of this research shows that the variation concrete of 0.25% and 0.5% have increased of tensile strength than the normal concrete as 12.272% and 4.369%. Beside that for the variation concrete of 0.75% and 1% have decreased as 5.044% and 11.929%. The increase of tensile strength value of optimal concrete is found in variation 0.25% that is 12.272% from normal concrete.

scholarly journals STUDI PEMANFAATAN ABU TERBANG LIMBAH HASIL PEMBAKARAN CAMPURAN CANGKANG DAN SERABUT KELAPA SAWIT SEBAGAI SUBSTITUSI SEMEN PADA PEMBUATAN BETON NORMAL DI LAHAN BASAH

INFO-TEKNIK ◽  
2020 ◽  
Vol 21 (2) ◽  
pp. 227
Author(s):  
Fauzi Rahman ◽  
Gawit Hidayat ◽  
Novita Bertiani
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Oil Palm ◽  
Combustion Process ◽  
Strength Test ◽  
Strength Analysis ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Tensile Strength Test

According to the Badan Pusat Statistik data in 2018, the total area of oil palm plantations in Indonesia currently reaches around 12.3 million hectares. Solid waste is the most waste, which is around 35-40% of the total Fresh Fruit Bunches (FFB) which is processed in the form of empty fruit bunches, fiber, fruit shells, and burnt ash. PT. Hasnur Citra Terpadu in Rantau, Tapin Regency, South Kalimantan is one of the Palm Oil Mill which in the combustion process of a boiler engine using oil palm shells and fibers is burned simultaneously. The result of the combustion process produces waste in the form of boiler crust ash which is fine textured (fly ash) and coarse textured (bottom ash). This study uses fly ash as a cement substitution for concrete mixtures. The making of mortar specimens was varied with fly ash with a percentage of 0%, 10%, 15%, 20% and 25% which will be tested for compressive strength at the age of 3 days, 7 days, 14 days, 21 days, and 28 days. Then the making of concrete specimens is planned with a quality of 25 MPa and the concrete compressive strength is tested at the age of 3 days, 7 days, 14 days, 28 days and 56 days and the split tensile strength test of the concrete at 28 days. Based on the results of the mortar compressive strength analysis, the optimum mixture of fly ash is 10% which is used for making concrete. The average compressive strength of normal concrete at 28 days is 26.33 MPa and the compressive strength of concrete with 10% fly ash (optimum concrete) is 26.14 MPa exceeding the design compressive strength of 25 MPa. Based on the results of the split tensile strength test of concrete at the age of 28 days, it was obtained 3,914 MPa for normal concrete and 3,466 MPa for optimum concrete.

scholarly journals PENGARUH PENGGUNAAN LIMBAH PLASTIK POLYPROPYLENE (PP) SEBAGAI CAMPURAN AGREGAT KASAR TERHADAP KUAT TEKAN DAN TARIK PADA BETON FC’ 25 MPA

2019 ◽  
Vol 3 (2) ◽  
pp. 81-89
Author(s):  
Angga Pirman Firdaus ◽  
Jonbi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Strength Test ◽  
Plastic Waste ◽  
Concrete Mixture ◽  
Strength Testing ◽  
Concrete Compressive Strength ◽  
Tensile Strength Test ◽  
Compressive Strength Test ◽  
Waste Mixture

Indonesia ranks second in the world's largest plastic waste producer after China. Each year, Indonesia can contributeup to 187.2 million tons of plastic waste, while China reaches 262.9 million tons of plastic waste. Based on the data, one way to utilize plastic waste by using plastic waste as a mixture of concrete, where the plastic used is polypropylene (PP) plastic with different percentage of concrete mixture, the test includes compressive strength test and tensile concrete. The results of concrete compressive strength testing with polypropylene (PP) plastic waste mixture of 5%, 10% and 15% at age 28 in aggregate aggregate mixture decreased by 5.15%, 6.89% and 13.53%. As for the result of concrete tensile strength test with polypropylene (PP) plastic waste mixture of 5%, 10% and 15% at age 28 in crude aggregate mixture decreased 17,61%, 24,13% dan 23,24%.

scholarly journals PERANCANGAN ALAT UJI TARIK MORTAR MENGGUNAKAN TENAGA PENGGERAK MOTOR LISTRIK

2018 ◽  
Vol 17 (1) ◽  
Author(s):  
Sarito Sarito ◽  
Muhtarom Riyadi ◽  
Handi Sudardja
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Building Material ◽  
Civil Engineering ◽  
Strength Test ◽  
Fine Aggregate ◽  
Trial Period ◽  
Tensile Strength Test ◽  
Engineering State

ABSTRACTMechanic characteristics of hard mortar are: compressive strength, flexural strength, tensile strength, and adhesion power. In the meantime, at Building Material Laboratory of Civil Engineering, State Polytechnic of Jakarta, test of tensile strength and adhesion power of mortar cannot be conducted because of the absence of the test equipment.This research aims to provide electric motor-powered equipment for tensile strength test of mortar in order to complete the equipment at Building Material Laboratory of Civil Engineering, State Polytechnic of Jakarta. The particular aim of the research is to make prototype of mortar tensile strength test equipment.In this research a prototype of motor-powered mortar tensile strength test equipment and the specimens, to test the performance of the equipment, were prepared. By examining the obstacles and shortcomings, this equipment is a development of the previous research by Muhtarom Riyadi and the team, 2015. The specimens, as the sample to test the equipment, were prepared by the ratio of one part of cement and three part of fine aggregate, with the total number of the specimens of 50 pieces.By analyzing the result of observation in trial period, the equipment could function as it should be. The magnitude of maximum tensile strength that causes the mortar specimens to break depends on the quality, age, and tensile area of mortar, which magnitude can be observed in manometer or scale with the unit of kilogram.Keywords: equipment, tensile, mortar, electric motorABSTRAKSifat mekanis mortar keras antara lain kuat tekan, kuat lentur, kuat tarik dan daya lekat. Sementara ini di Laboratorium bahan bangunan Jurusan Teknik Sipil Politeknik Negeri Jakarta untuk uji kuat tarik dan daya lekat mortar belum bisa dilaksanakan karena belum adanya peralatan untuk melakukan pengujian.Penelitian ini bertujuan untuk membuat alat uji tarik mortar menggunakan tenaga penggerak motor listrik guna melengkapi peralatan yang diperlukan di Laboratorium bahan bangunan Jurusan Teknik Sipil Politeknik Negeri Jakarta. Target khusus yang ingin dicapai adalah membuat prototype alat uji tarik mortar.Dalam penelitian ini akan dibuat prototipe alat uji tarik mortar menggunakan tenaga motor listrik dan cetakan benda ujinya, sekaligus untuk menguji kinerjanya. Alat ini merupakan pengembangan oleh peneliti yang terdahulu Muhtarom Riyadi dan anggotanya, 2015), dengan mencermati kendala dan kekurangannya maka penelitian ini merupakan penyempurnaan penelitian sebelumnya Sebagai sampelnya dibuat benda uji tarik mortar dengan perbandingan 1 bagian semen berbanding 3 bagian pasir, sedangkan jumlah benda uji dibuat sebanyak 50 buah.Hasil pengamatan selama uji coba maka alat alat uji tarik mortar menggunakan tenaga penggerak motor listrik dapat berfungsi sebagaimana mestinya. Besarnya gaya tarik maksimum yang menjadikan benda uji tarik mortar putus tergantung dari mutu mortar, umur serta luas penampang tarik yang nilainya dapat diamatai pada manometer atau timbangan berat dengan satuan kilogramKata kunci : Alat, uji, tarik, mortar, motor listrik

scholarly journals Evaluation of physical-mechanical properties of self-adhesive versus conventional resin cements

2020 ◽  
Vol 19 ◽  
pp. e208204
Author(s):  
Maria Helena Rossy Borges ◽  
Carmen Gilda Tavares Dias ◽  
Cristiane de Melo Alencar ◽  
Cecy Martins Silva ◽  
Renata Antunes Esteves
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Testing Machine ◽  
Strength Test ◽  
Resin Cement ◽  
Resin Cements ◽  
Tensile Strength Test ◽  
Diametral Tensile Strength ◽  
One Way Anova

Aim: The purpose of this study was to compare the microhardness, diametral tensile strength, compressive strength and the rheological properties of self-adhesive versus conventional resin cements. Methods: Specimens of a conventional (RelyX ARC) and 3 self-adhesive (RelyX U200, Maxcem Elite, Bifix SE) types of resin cements were prepared. The Knoop test was used to assess the microhardness, using a Microhardness Tester FM 700. For the diametral tensile strength test, a tensile strength was applied at a speed of 0.6 mm/minute. A universal testing machine was used for the analysis of compressive strength and a thermo-controlled oscillating rheometer was used for the Rheology test. One-way ANOVA and Tukey’s test (α=0.05) were used for data analysis. Results: According to microhardness analysis, all the cements were statistically similar (p>0.05), except for Maxcem that presented lower hardness compared with the other cements in relation to the top surface (p<0.05). In the diametral tensile strength test, Relyx U200 and RelyX ARC cements were statistically similar (p>0.05), presented higher value when compared to the Maxcem and Bifix cements (p<0.05). The compressive strength of RelyX ARC and Maxcem Elite cements was statistically higher than RelyX U200 and Bifix cements (p<0.05). Regarding the rheology test, Maxcem Elite and RelyX ARC cements showed a high modulus of elasticity. Conclusions: The self-adhesive cements presented poorer mechanical properties than conventional resin cement. Chemical structure and types of monomers employed interfere directly in the mechanical properties of resin cements.

Effect of Mixing Steel Dust and Shred-Like Steel Fibres on the Properties of Concrete

2019 ◽  
Vol 7 (1) ◽  
pp. 24-29
Author(s):  
A. Ajwad ◽  
N. Khadim ◽  
Abdullah ◽  
U. Ilyas ◽  
M. U. Rashid ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Strength Test ◽  
Hardened Concrete ◽  
Normal Concrete ◽  
Steel Fibres ◽  
Coarse Aggregates ◽  
Mix Proportion ◽  
Steel Dust

In this research, fine and coarse aggregates present in the concrete are replaced with steel dust and shred-like steel fibres, respectively in different ratios and its effect on the properties of concrete is studied. Eight batches of concrete were mixed, each with the mix proportion of 1:2:4 and water cement ratio of 0.52. Batch A was of normal concrete. In batches B, C, and D, 5%, 10%, and 15% of sand was replaced with steel dust. In batches, E, F, and G, 2%, 5%, and 8% of coarse aggregate were replaced with steel fibres. In the last batch H, both 5% of sand and 5% of coarse aggregate were replaced with steel fine and steel fibres respectively. British as well as American standards were followed during the research. Slump test was performed in a fresh state of each mix to find the effect of these replacements on workability. 12 cubes of 150mm x 150mm x 150mm for compressive strength test and 12 cylinders of 150mm diameter and 300mm height of each, for tensile strength test were made for each batch to check these strength after 3, 7, 14, 28 days. It was found that the workability of fresh concrete decreases while density of fresh as well as hardened concrete increases with these replacements. It also results in an increase in initial compressive strength and a decrease in final compressive strength as compared to those of normal concrete. As far as tensile strength is concerned an increase in initial as well as final strength was observed.

scholarly journals Strength of Concrete using Clay as a Partial Replacement of Binder Content with and Without Lime

2021 ◽  
Vol 10 (3) ◽  
pp. 1-6
Author(s):  
S. B. Kandekar ◽  
◽  
S. K. Wakchaure ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Hydrated Lime ◽  
Strength Test ◽  
Binder Content ◽  
Partial Replacement ◽  
Split Tensile Strength ◽  
Tensile Strength Test ◽  
Compressive Strength Test

Materials are the most important component of building construction. The demands of construction material are increasing day by day significantly. This demand is increasing the material prices and scarcity of material in construction industry. To achieve economical and eco-friendly criteria naturally occurring material is selected. Clay is a natural material and it can be available easily. This paper interprets the experimental investigation on strength of concrete using clay as a partial replacement to binder content (cement) in concrete. The replacement percentages are grouped as 0%, 10%, 20%, 30%, 40% of clay and 5% of hydrated lime with cement in each series in M25 grade of concrete. To achieve the pozzolanic property of clay hydrated lime was added. Different tests are performed to determine the optimum percentage of clay as a replacement for binder content (cement) in concrete. The Compressive strength test, split tensile strength test and flexural strength test were performed on the specimens. Total 90 cubes of size 150 mm were prepared for compressive strength test, 30 cylinders of 150 mm diameter and 300 mm height were prepared for split tensile strength test and 30 beams of size 150 mm x 150 mm x 1000 mm were prepared to carry out the flexural strength test. The results are compared to find the ideal proportion of clay as a replacement for cement. It is found that 10% replacement with 5% hydrated lime gives satisfactory results.

scholarly journals PENGARUH LAMA PENGERINGAN BETON SERAT PANDAN PUNDAK DURI (PANDANUS TECTORIUS) TERHADAP KUAT TARIK BELAH BETON

2019 ◽  
Vol 11 (1) ◽  
pp. 1-6
Author(s):  
Faizal Hadi ◽  
Agustin Gunawan
Keyword(s):  
Tensile Strength ◽  
Strength Test ◽  
Mix Design ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Tensile Strength Test ◽  
Pandanus Tectorius

Concrete is a material that have the strength to compression, but it is weak against tensile strength. The weakness of the tensile strength of concrete can be minimized by adding pandanus tectorius fiber. This study was aimed to determine the effect of adding pandanus tectorius fiber to split- tensile strength of concrete and percentage of the fiber in concrete that shows the highest split- tensile strength. The specimens used in this study is cylindrical with dimensions of 30 cm in height and 15 cm in diameter (SNI 03-4810-1998). Total of specimens is 32 that consist of 8 normal concretes and 24 variation concretes. An addition of pandanus tectorius fiber with the variation of 0,25%, 0,5%, and 0,75% was based on volume of the specimen. The mix design of concrete used water-cement ratio of 0.5 and slump of 60-100 mm. The splittensile strength of concrete was tested at 7 days and 14 days of dryng after immersing for 27 days. The result of split-tensile strength test of concrete with a variation of pandanus tectorius fiber showed a decreasing. The decreasing of split-tensile strength of concrete at 41 days was smaller than at 34 days to normal concrete. The highest decreasing percentage of split-tensile strength of variation concrete to normal concrete was respectively 9,249% (variation 0,25 tested at 41 days) and 14,518% (variation 0,75% tested at 34 days) .

scholarly journals Strength Properties of Untreated Coal Bottom Ash as Cement Replacement

2020 ◽  
Vol 6 (1) ◽  
pp. 13 ◽  
Author(s):  
Noraziela Syahira Baco ◽  
Shahiron Shahidan ◽  
Sharifah Salwa Mohd Zuki ◽  
Noorwirdawati Ali ◽  
Mohamad Azim Mohammad Azmi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Bottom Ash ◽  
Strength Test ◽  
Splitting Tensile Strength ◽  
Curing Time ◽  
Coal Bottom Ash ◽  
Cement Replacement ◽  
Tensile Strength Test ◽  
Compressive Strength Test

Coal Bottom Ash (CBA) is a mineral by-product of thermal power plants obtained from the combustion of coal. In many countries, CBA wastes are identified as hazardous materials. The utilization of CBA can help in alleviating environmental problems; thus, this research was carried out to explore the possibility of its use as cement replacement in concrete manufacturing. Presently, In Malaysia, research that concerns about the use of CBA as cement replacement is very limited. Therefore, this study was aimed to investigate the properties of CBA as cement replacement and to identify the optimum percentage of untreated CBA as cement replacement. The CBA used in this study were taken from the Tanjung Bin power plant. In this research, the amount of CBA in the concrete mixture varied from 20% to 40% to replace cement. The properties of concrete containing CBA as cement replacement was examined through slump test, sieve analysis, concrete compressive strength test and splitting tensile strength test. The compressive strength test and splitting tensile strength test were performed at 7 and 28 days of curing time. Based on this research, it can be concluded that the optimum percentage of CBA as cement replacement is 25% for a curing time of both 7 and 28 days with the concrete compression strength of 45.2 MPa and 54.6 MPa, respectively. Besides, the optimum percentage for tensile strength is also at 25% CBA for a curing period of both 7 and 28 days with the tensile strength of 2.91 MPa and 3.28 MPa, respectively. 

scholarly journals STUDI KELAYAKAN MATERIAL GUNUNG DAERAH ALIRAN SUNGAI ARAH MALANG-KOTA BATU DALAM PENGGUNAANNYA SEBAGAI SALAH SATU MATERIAL BETON

2021 ◽  
Vol 14 (2) ◽  
pp. 30
Author(s):  
Armin Naibaho ◽  
Agus Sugiarto ◽  
Purnama Dewi
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Building Materials ◽  
High Efficiency ◽  
Coarse Aggregate ◽  
Strength Test ◽  
Fine Aggregate ◽  
Split Tensile Strength ◽  
Tensile Strength Test ◽  
Compressive Strength Test

Abstract The use of the mountain seal used as a building block for concrete should be considered, based on current usage apart from being a light construction material for housing, mountain materials from these two places are used as the main aggregate material for building construction, water structures (dams), roads. and bridges located in the surrounding Malang-Kota Batu area To determine the size of the aggregate, the coarse aggregate is sieved using a vibrating sieve, while the fine aggregate is sieved by a hydraulic sieve. In the screening process, about 70% of the filtered must pass so that high efficiency and capacity can be achieved. The compressive strength test results obtained the average compressive strength value at 28 days of concrete for concrete with fine aggregate sand zone III and coarse aggregate (gravel) in the Batu City area is equivalent to 35.65 MPa. The results of the split tensile strength test showed that the average split strength value at the age of 28 days for concrete with fine aggregate sand zone III and coarse aggregate (gravel) in the Kota Batu area is equivalent to 2.51 MPa. The compressive strength value for normal concrete is 35.65 MPa, it should produce split tensile strength = 4.179 MPa according to the provisions of SNI T-15-1991-03 Article 3.2.5 (fr = 0.70√fc '). Even though the split tensile strength value obtained in the laboratory is only 2.51 MPa, this means that the quality of materials (sand and broken stone) from Batu City is not suitable for use as building materials. Because the number 2.51 MPa is relatively much smaller than the value of 4.179 MPa, it is only one of the factors outlined in the SNI T-15-1991-03 article 3.2.5. Keywords: Mountain Material, Concrete, Concrete Compressive Strength Test, Concrete Tensile Strength Test

Sign in / Sign up

Export Citation Format

Share Document