scholarly journals Numerical Simulation of Inline Forces on a Bottom-Mounted Circular Cylinder Under the Action of a Specific Freak Wave

2020 ◽  
Vol 7 ◽  
Author(s):  
Yuqi Wang ◽  
Fuyou Xu ◽  
Zhanbiao Zhang
Keyword(s):  
Circular Cylinder ◽  
Load Cycle ◽  
Offshore Wind ◽  
Return Flow ◽  
Wave Forces ◽  
Freak Waves ◽  
Simulation Accuracy ◽  
Freak Wave ◽  
Simulation Results ◽  
Classic Form

Freak waves pose a great threat to the tension-leg platforms (TLPs) and monopile foundations of offshore wind turbines (OWTs), which necessitates comprehensive investigations on the characteristics of freak waves and the wave actions on those offshore renewable energy structures with circular cylinder. The recorded freak wave series “New Year Wave” (NYW) was numerically simulated using the Computational Fluid Dynamics methods. The compensation measure was adopted to effectively improve simulation accuracy. Under the action of the NYW, the inline forces and secondary load cycle (SLC) on a vertical-mounted cylinder, as the classic form for the TLPs and foundation of OWTs, were fully addressed. The simulation results were compared with the empirical formulations and experimental data to reveal the differences and the possible causes. The development of SLC was found to be closely related to the downstream vortex and return flow, which induces the reduction of the wall pressure and thus the inline force. The maximum inline forces vary with the cylinder position relative to the wave peak, and the simulation results reveal that the linear inline forces calculated by Morison formulation may be less than 65% of the total wave forces.

A Numerical Prediction on the Transient Response of a Spar-Type Floating Offshore Wind Turbine in Freak Waves

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Yan Li ◽  
Xiaoqi Qu ◽  
Liqin Liu ◽  
Peng Xie ◽  
Tianchang Yin ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Offshore Wind ◽  
Numerical Code ◽  
Modulation Method ◽  
Offshore Wind Turbine ◽  
Freak Waves ◽  
Freak Wave ◽  
Floating Offshore Wind Turbine ◽  
The Impact

Abstract Simulations are conducted in time domain to investigate the dynamic response of a spar-type floating offshore wind turbine (FOWT) under the freak wave scenarios. Toward this end, a coupled aero-hydro-mooring in-house numerical code is adopted to perform the simulations. The methodology includes a blade-element-momentum (BEM) model for simulating the aerodynamic loads, a nonlinear model for simulating the hydrodynamic loads, a nonlinear restoring model of Spar buoy, and a nonlinear algorithm for simulating the mooring cables. The OC3 Hywind spar-type FOWT is adopted as an example to study the dynamic response under the freak wave conditions, meanwhile the time series of freak waves are generated using the random frequency components selection phase modulation method. The motion of platform, the tension applied on the mooring lines, and the power generation performance are documented in several cases. According to the simulations, it is indicated that when a freak wave acts on the FOWT, the transient motion of the FOWT is induced in all degrees-of-freedom, as well as the produced power decreases rapidly. Furthermore, the impact of freak wave parameters on the motion of FOWT is discussed.

scholarly journals Characteristics of Breaking Wave Forces on Piles over a Permeable Seabed

2021 ◽  
Vol 9 (5) ◽  
pp. 520
Author(s):  
Zhenyu Liu ◽  
Zhen Guo ◽  
Yuzhe Dou ◽  
Fanyu Zeng
Keyword(s):  
Wave Breaking ◽  
Stokes Equations ◽  
Slope Angle ◽  
Wave Force ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Secondary Wave ◽  
Wave Forces ◽  
Breaking Wave ◽  
Breaking Wave Forces

Most offshore wind turbines are installed in shallow water and exposed to breaking waves. Previous numerical studies focusing on breaking wave forces generally ignored the seabed permeability. In this paper, a numerical model based on Volume-Averaged Reynolds Averaged Navier–Stokes equations (VARANS) is employed to reveal the process of a solitary wave interacting with a rigid pile over a permeable slope. Through applying the Forchheimer saturated drag equation, effects of seabed permeability on fluid motions are simulated. The reliability of the present model is verified by comparisons between experimentally obtained data and the numerical results. Further, 190 cases are simulated and the effects of different parameters on breaking wave forces on the pile are studied systematically. Results indicate that over a permeable seabed, the maximum breaking wave forces can occur not only when waves break just before the pile, but also when a “secondary wave wall” slams against the pile, after wave breaking. With the initial wave height increasing, breaking wave forces will increase, but the growth can decrease as the slope angle and permeability increase. For inclined piles around the wave breaking point, the maximum breaking wave force usually occurs with an inclination angle of α = −22.5° or 0°.

Detailed Study on Breaking Wave Interactions With a Jacket Structure Based on Experimental Investigations

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Jithin Jose ◽  
Olga Podrażka ◽  
Ove Tobias Gudmestad ◽  
Witold Cieślikiewicz
Keyword(s):  
Wind Turbines ◽  
Wave Breaking ◽  
Offshore Structures ◽  
Offshore Wind ◽  
Wave Forces ◽  
Breaking Wave ◽  
Offshore Wind Turbines ◽  
Wave Parameters ◽  
Wave Slamming ◽  
Breaking Wave Forces

Wave breaking is one of the major concerns for offshore structures installed in shallow waters. Impulsive breaking wave forces sometimes govern the design of such structures, particularly in areas with a sloping sea bottom. Most of the existing offshore wind turbines were installed in shallow water regions. Among fixed-type support structures for offshore wind turbines, jacket structures have become popular in recent times as the water depth for fixed offshore wind structures increases. However, there are many uncertainties in estimating breaking wave forces on a jacket structure, as only a limited number of past studies have estimated these forces. Present study is based on the WaveSlam experiment carried out in 2013, in which a jacket structure of 1:8 scale was tested for several breaking wave conditions. The total and local wave slamming forces are obtained from the experimental measured forces, using two different filtering methods. The total wave slamming forces are filtered from the measured forces using the empirical mode decomposition (EMD) method, and local slamming forces are obtained by the frequency response function (FRF) method. From these results, the peak slamming forces and slamming coefficients on the jacket members are estimated. The breaking wave forces are found to be dependent on various breaking wave parameters such as breaking wave height, wave period, wave front asymmetry, and wave-breaking positions. These wave parameters are estimated from the wave gauge measurements taken during the experiment. The dependency of the wave slamming forces on these estimated wave parameters is also investigated.

Non-Gaussian Extreme Waves in the Central North Sea

1997 ◽  
Vol 119 (3) ◽  
pp. 146-150 ◽  
Author(s):  
J. Skourup ◽  
N.-E. O. Hansen ◽  
K. K. Andreasen
Keyword(s):  
Wave Height ◽  
North Sea ◽  
Upper Bound ◽  
Wave Crest ◽  
Extreme Waves ◽  
Freak Waves ◽  
Freak Wave ◽  
Wave Trains ◽  
Central North Sea ◽  
Crest Height

The area of the Central North Sea is notorious for the occurrence of very high waves in certain wave trains. The short-term distribution of these wave trains includes waves which are far steeper than predicted by the Rayleigh distribution. Such waves are often termed “extreme waves” or “freak waves.” An analysis of the extreme statistical properties of these waves has been made. The analysis is based on more than 12 yr of wave records from the Mærsk Olie og Gas AS operated Gorm Field which is located in the Danish sector of the Central North Sea. From the wave recordings more than 400 freak wave candidates were found. The ratio between the extreme crest height and the significant wave height (20-min value) has been found to be about 1.8, and the ratio between extreme crest height and extreme wave height has been found to be 0.69. The latter ratio is clearly outside the range of Gaussian waves, and it is higher than the maximum value for steep nonlinear long-crested waves, thus indicating that freak waves are not of a permanent form, and probably of short-crested nature. The extreme statistical distribution is represented by a Weibull distribution with an upper bound, where the upper bound is the value for a depth-limited breaking wave. Based on the measured data, a procedure for determining the freak wave crest height with a given return period is proposed. A sensitivity analysis of the extreme value of the crest height is also made.

Experimental Study of Wave Force Distribution on a Monopile Structure

2018 ◽  
Author(s):  
Malene H. Vested ◽  
Stefan Carstensen ◽  
Erik Damgaard Christensen
Keyword(s):  
Experimental Studies ◽  
Cost Effective ◽  
Wave Force ◽  
Offshore Wind ◽  
Irregular Waves ◽  
Force Distribution ◽  
Wave Forces ◽  
Total Force ◽  
Wave Flume ◽  
Effective Manner

As the demand for offshore wind energy continues to grow, the strive to understand the wave forces acting on the substructure of the wind turbines continues. In regard to wind turbine design, it is vital to consider not only the total wave force, but also the local wave forces. Local forces are particularly important for the design of secondary structures as e.g. mooring platforms. Typically, however, experimental studies mainly concern total forces or idealized local forces. We present here a rather simple way to measure local forces along a model monopile. The study is conducted in a wave flume of 28 m in length, in which waves are generated by a piston-type wave maker at a water depth of 0.515 m and shoal onto a bed of slope 1:25. A model monopile is installed and subjected to forcing from a series of both regular and irregular waves. In the experimental set-up, the model monopile is fixed at the bottom and the top and consists of seven independent cylindrical sections. The cylindrical sections are connected by force transducers which measure local shear, and so the associated local forces may be determined. The measured local forces are compared to the force distribution given by Morisons equation combined with linear theory and Wheeler stretching, which is a force estimate commonly used in the industry. This study shows that the total force is rather well captured by Morison’s equation. The force distribution estimated from Morison’s equation, however, shows larger discrepancies from the measured forces. This encourages for further measurements. In this study, we show that it is possible to measure force distribution on a model monopile in a simple and cost-effective manner. The aim is here to demonstrate the method and we will later present a larger body of work associated with the outcome of the measurements.

A numerical model for earthquake-induced hydrodynamic forces and wave forces on inclined circular cylinder

2020 ◽  
Vol 207 ◽  
pp. 107382 ◽  
Author(s):  
Piguang Wang ◽  
Xiaojing Wang ◽  
Mi Zhao ◽  
Xinglei Cheng ◽  
Xiuli Du
Keyword(s):  
Numerical Model ◽  
Circular Cylinder ◽  
Hydrodynamic Forces ◽  
Wave Forces

Experimental Study on the Wave Loads on Monopile and Jacket Type Support of Offshore Wind Turbines

2018 ◽  
Author(s):  
Jing Zhang ◽  
Qin Liu ◽  
Xing Hua Shi ◽  
C. Guedes Soares
Keyword(s):  
Experimental Study ◽  
Wind Turbine ◽  
Nonlinear Wave ◽  
Wave Force ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Forces ◽  
Wave Loads ◽  
Morison Equation ◽  
Offshore Wind Turbines

As the offshore fixed wind turbine developed, more ones will be installed in the sea field with the depth 15–50 meters. Wave force will be one of the main forces that dominate the design of the wind turbine base, which is calculated using the Morison equation traditionally. This method can predict the wave forces for the small cylinders if the drag and inertia coefficients are obtained accurately. This paper will give a series scaled tests of monopile and jacket type base of the offshore wind turbine in tank to study the nonlinear wave loads.

Freak Wave Generation in a Wave Basin With HOSM-WG Method

2015 ◽  
Author(s):  
Hidetaka Houtani ◽  
Takuji Waseda ◽  
Wataru Fujimoto ◽  
Keiji Kiyomatsu ◽  
Katsuji Tanizawa
Keyword(s):  
Control Method ◽  
Irregular Waves ◽  
Frequency Bandwidth ◽  
Freak Waves ◽  
Freak Wave ◽  
Wave Basin ◽  
Wave Trains ◽  
Directional Wave ◽  
Wave Maker ◽  
The Difference

A method to produce freak waves with arbitrary spectrum in a fully directional wave basin is presented here. This is an extension of Waseda, Houtani and Tanizawa at OMAE 2013[1], which used “HOSM-WG” based on the higher-order spectral method (HOSM). We used the following three methods to improve the HOSM-WG in [1]: “separation of free waves from bound waves,” “using Biesel’s transfer function in wavenumber space” and “using Schaffer’s 2nd-order wave maker control method.” Modulational wave trains, freak waves in unidirectional irregular waves and freak waves in short-crested irregular waves were generated in a wave basin. The experimental results using the improved HOSM-WG were compared to the HOSM simulation, and good agreements were found. The effectiveness of the improved HOSM-WG was ascertained. We showed that the difference between HOSM-WG and HOSM simulations became larger as wave steepness, frequency bandwidth of the spectrum or directional spreading became larger.

Sign in / Sign up

Export Citation Format

Share Document