scholarly journals Effects of Hydrothermal Pretreatment and Hydrochar Addition on the Performance of Pig Carcass Anaerobic Digestion

2021 ◽  
Vol 12 ◽  
Author(s):  
Jie Xu ◽  
Hongjian Lin ◽  
Kuichuan Sheng
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Ammonia Concentration ◽  
Hydrothermal Pretreatment ◽  
Biogas Yield ◽  
Stirred Tank Reactors ◽  
Liquid Products ◽  
Pig Carcasses

Proper disposal and utilization of dead pig carcasses are problems of public concern. The combination of hydrothermal pretreatment (HTP) and anaerobic digestion is a promising method to treat these wastes, provided that digestion inhibition is reduced. For this reason, the aim of this work was to investigate the optimal HTP temperature (140–180°C) for biogas production during anaerobic digestion of dead pigs in batch systems. In addition, the effects of hydrochar addition (6 g/L) on anaerobic digestion of pork products after HTP in continuous stirred tank reactors (CSTR) were determined. According to the results, 90% of lipids and 10% of proteins present in the pork were decomposed by HTP. In addition, the highest chemical oxygen demand (COD) concentration in liquid products (LP) reached 192.6 g/L, and it was obtained after 170°C HTP. The biogas potential from the solid residue (SR) and LP was up to 478 mL/g-VS and 398 mL/g-COD, respectively. A temperature of 170°C was suitable for pork HTP, which promoted the practical biogas yield because of the synergistic effect between proteins and lipids. Ammonia inhibition was reduced by the addition of hydrochar to the CSTR during co-digestion of SR and LP, maximum ammonia concentration tolerated by methanogens increased from 2.68 to 3.38 g/L. This improved total biogas yield and degradation rate of substrates, reaching values of 28.62 and 36.06%, respectively. The acetate content in volatile fatty acids (VFA) may be used as an index that reflects the degree of methanogenesis of the system. The results of the present work may also provide guidance for the digestion of feedstock with high protein and lipid content.

scholarly journals Biogas Generation through Anaerobic Digestion of Compost Leachate in Semi-Continuous Completely Stirred Tank Reactors

Processes ◽  
2019 ◽  
Vol 7 (9) ◽  
pp. 635 ◽  
Author(s):  
Siciliano ◽  
Limonti ◽  
Curcio ◽  
Calabrò
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Stirred Tank ◽  
Organic Load ◽  
Stirred Tank Reactors ◽  
Load Rate ◽  
Compost Leachate

The composting process of organic fraction of municipal solid waste, besides to the residual compost, generates a wastewater that is characterized by a high organic load. The application of anaerobic processes represents an advantageous solution for the treatment and valorization of this type of wastewater. Nevertheless, few works have been focused on the anaerobic digestion of compost leachate. To overcome this dearth, in the present paper an extensive experimental investigation was carried out to develop and analyse the anaerobic treatment of young leachate in completely stirred tank reactors (CSTR). Initially, it was defined a suitable leachate pretreatment to correct its acidic characteristics that is potentially able to inhibit methanogenic biomass activity. The pretreated leachate was fed to the digester over the start-up phase that was completed in about 40 days. During the operational period, the organic load rate (OLR) changed between 4.25 kgCOD/m3d and 38.5 kgCOD/m3d. The chemical oxygen demand (COD) abatement was higher than 90% for OLR values up to 14.5 kgCOD/m3d and around to 80% for applied loads equal to 24.5 kgCOD/m3d. At this OLR, it was reached the maximum daily biogas production of about 9.3 Lbiogas/(Lreactord). The CH4 fraction was between 70%–78% and the methane production yield in the range 0.34–0.38 LCH4/gCODremoved. The deterioration of biogas production started for OLR values that were over the threshold of 24.5 kgCOD/m3d when a volatile fatty acids (VFA) accumulation occurred and the pH dropped below 6.5. The maximum ratio between VFA and alkalinity (ALK) tolerable in the CSTR was identified to be 0.5 gCH3COOH/gCaCO3. Through an economic analysis, it was proven that the digestion of compost leachate could ensure significant economic profits. Furthermore, the produced digestate had characteristics that were compatible for agricultural applications.

Alkali pre-treatment of Sorghum Moench for biogas production

2013 ◽  
Vol 67 (9) ◽  
Author(s):  
Karina Michalska ◽  
Stanisław Ledakowicz
Keyword(s):  
Anaerobic Digestion ◽  
Chemical Oxygen Demand ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Total Phenolic ◽  
Methane Generation ◽  
Pre Treatment ◽  
Alkali Hydrolysis ◽  
Almost All

AbstractThis work studies the influence of the alkali pre-treatment of Sorghum Moench — a representative of energy crops used in biogas production. Solutions containing various concentrations of sodium hydroxide were used to achieve the highest degradation of lignocellulosic structures. The results obtained after chemical pre-treatment indicate that the use of NaOH leads to the removal of almost all lignin (over 99 % in the case of 5 mass % NaOH) from the biomass, which is a prerequisite for efficient anaerobic digestion. Several parameters, such as chemical oxygen demand, total organic carbon, total phenolic content, volatile fatty acids, and general nitrogen were determined in the hydrolysates thus obtained in order to define the most favourable conditions. The best results were obtained for the Sorghum treated with 5 mass % NaOH at 121°C for 30 min The hydrolysate thus achieved consisted of high total phenolic compounds concentration (ca. 4.7 g L−1) and chemical oxygen demand value (ca. 45 g L−1). Although single alkali hydrolysis causes total degradation of glucose, a combined chemical and enzymatic pre-treatment of Sorghum leads to the release of large amounts of this monosaccharide into the supernatant. This indicates that alkali pre-treatment does not lead to complete cellulose destruction. The high degradation of lignin structure in the first step of the pre-treatment rendered the remainder of the biomass available for enzymatic action. A comparison of the efficiency of biogas production from untreated Sorghum and Sorghum treated with the use of NaOH and enzymes shows that chemical hydrolysis improves the anaerobic digestion effectiveness and the combined pre-treatment could have great potential for methane generation.

scholarly journals Evaluation of Anaerobic Digestion of Dairy Wastewater in an Innovative Multi-Section Horizontal Flow Reactor

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2392 ◽  
Author(s):  
Marcin Dębowski ◽  
Marcin Zieliński ◽  
Marta Kisielewska ◽  
Joanna Kazimierowicz
Keyword(s):  
Wastewater Treatment ◽  
Anaerobic Digestion ◽  
Flow Reactor ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Methane Content ◽  
Dairy Wastewater ◽  
Horizontal Flow ◽  
Organic Loading Rate ◽  
Biogas Yield

The aim of this study was the performance evaluation of anaerobic digestion of dairy wastewater in a multi-section horizontal flow reactor (HFAR) equipped with microwave and ultrasonic generators to stimulate biochemical processes. The effects of increasing organic loading rate (OLR) ranging from 1.0 g chemical oxygen demand (COD)/L·d to 4.0 g COD/L·d on treatment performance, biogas production, and percentage of methane yield were determined. The highest organic compounds removals (about 85% as COD and total organic carbon—TOC) were obtained at OLR of 1.0–2.0 g COD/L·d. The highest biogas yield of 0.33 ± 0.03 L/g COD removed and methane content in biogas of 68.1 ± 5.8% were recorded at OLR of 1.0 g COD/L·d, while at OLR of 2.0 g COD/L·d it was 0.31 ± 0.02 L/COD removed and 66.3 ± 5.7%, respectively. Increasing of the OLR led to a reduction in biogas productivity as well as a decrease in methane content in biogas. The best technological effects were recorded in series with an operating mode of ultrasonic generators of 2 min work/28 min break. More intensive sonication reduced the efficiency of anaerobic digestion of dairy wastewater as well as biogas production. A low nutrient removal efficiency was observed in all tested series of the experiment, which ranged from 2.04 ± 0.38 to 4.59 ± 0.68% for phosphorus and from 9.67 ± 3.36 to 20.36 ± 0.32% for nitrogen. The effects obtained in the study (referring to the efficiency of wastewater treatment, biogas production, as well as to the results of economic analysis) proved that the HFAR can be competitive to existing industrial technologies for food wastewater treatment.

Effect of Ultrasonic Pretreatment for the Anaerobic Digestion of Sewage Sludge

2012 ◽  
Vol 531 ◽  
pp. 528-531 ◽  
Author(s):  
Na Wei
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
High Concentration ◽  
Ultrasonic Pretreatment ◽  
Soluble Chemical Oxygen Demand ◽  
Pre Treatment ◽  
Settling Characteristics

Anaerobic digestion is an economic and environmentally friendly technology for treating the biomass material-sewage sludge, but has some limitations, such as the low efficient biogass production. In this paper ultrasound was proposed as pre-treatment for effective sludge anaerobic digestion. Sludge anaerobic digestion experiments with ultrasonic pretreatment was investigated. It can be seen that this treatment effectively leaded to the increase of soluble chemical oxygen demand(SCOD) and volatile fatty acids(VFA)concentration. High concentration of VFA leaded to a increase in biogas production. Besides, the SV of sludge was reduced and the settling characteristics of sludge was improved after ultrasonic pretreatment. It can be concluded that sludge anaerobic digestion with ultrasonic pretreatment is an effective method for biomass material transformation.

Sludge electrooxidation as pre-treatment for anaerobic digestion

2016 ◽  
Vol 75 (4) ◽  
pp. 775-781 ◽  
Author(s):  
J. A. Barrios ◽  
U. Duran ◽  
A. Cano ◽  
M. Cisneros-Ortiz ◽  
S. Hernández
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Wastewater Sludge ◽  
Boron Doped Diamond ◽  
Boron Doped ◽  
Treatment Conditions ◽  
Volatile Solids ◽  
Pre Treatment

Anaerobic digestion of wastewater sludge is the preferred method for sludge treatment as it produces energy in the form of biogas as well as a stabilised product that may be land applied. Different pre-treatments have been proposed to solubilise organic matter and increase biogas production. Sludge electrooxidation with boron-doped diamond electrodes was used as pre-treatment for waste activated sludge (WAS) and its effect on physicochemical properties and biomethane potential (BMP) was evaluated. WAS with 2 and 3% total solids (TS) achieved 2.1 and 2.8% solubilisation, respectively, with higher solids requiring more energy. After pre-treatment, biodegradable chemical oxygen demand values were close to the maximum theoretical BMP, which makes sludge suitable for energy production. Anaerobic digestion reduced volatile solids (VS) by more than 30% in pre-treated sludge with a food to microorganism ratio of 0.15 g VSfed g−1 VSbiomass. Volatile fatty acids were lower than those for sludge without pre-treatment. Best pre-treatment conditions were 3% TS and 28.6 mA cm−2.

Experimental and Artificial Neural Network Modeling of a Upflow Anaerobic Contactor (UAC) for Biogas Production from Vinasse

2016 ◽  
Vol 14 (6) ◽  
pp. 1241-1254 ◽  
Author(s):  
Ousman R. Dibaba ◽  
Sandip K. Lahiri ◽  
Stephan T’Jonck ◽  
Abhishek Dutta
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Organic Loading Rate ◽  
Neural Network Modeling ◽  
Artificial Neural

Abstract A pilot scale Upflow Anaerobic Contactor (UAC), based on upflow sludge blanket principle, was designed to treat vinasse waste obtained from beet molasses fermentation. An assessment of the anaerobic digestion of vinasse was carried out for the production of biogas as a source of energy. Average Organic loading rate (OLR) was around 7.5 gCOD/m3/day in steady state, increasing upto 8.1 gCOD/m3/day. The anaerobic digestion was conducted at mesophilic (30–37 °C) temperature and a stable operating condition was achieved after 81 days with average production of 65 % methane which corresponded to a maximum biogas production of 85 l/day. The optimal performance of UAC was obtained at 87 % COD removal, which corresponded to a hydraulic retention time of 16.67 days. The biogas production increased gradually with OLR, corresponding to a maximum 6.54 gCOD/m3/day (7.4 % increase from initial target). A coupled Artificial Neural Network-Differential Evolution (ANN-DE) methodology was formulated to predict chemical oxygen demand (COD), total suspended solids (TSS) and volatile fatty acids (VFA) of the effluent along with the biogas production. The method incorporated a DE approach for the efficient tuning of ANN meta-parameters such as number of nodes in hidden layer, input and output activation function and learning rate. The model prediction indicated that it can learn the nonlinear complex relationship between the parameters and able to predict the output of the contactor with reasonable accuracy. The utilization of the coupled ANN-DE model provided significant improvement to the study and helps to study the parametric effect of influential parameters on the reactor output.

Anaerobic digestion of deproteinated cheese whey

1985 ◽  
Vol 52 (3) ◽  
pp. 457-467 ◽  
Author(s):  
Johannes De Haast ◽  
Trevor J. Britz ◽  
Johannes C. Novello ◽  
Emilige W. Verwey
Keyword(s):  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Fixed Bed ◽  
Oxygen Demand ◽  
Ammonia Level ◽  
Fixed Bed Reactor ◽  
Total Carbon ◽  
Ammonia Toxicity ◽  
Biogas Yield ◽  
Titration Curves

SUMMARYWhey and deproteinated whey preparations with different carbon: nitrogen (C/N) ratios ranging from 7·5 to 73 were digested anaerobically in a downflow stationary fixed-bed reactor at 35 °C with a hydraulic retention time of 5 d. Effluent and biogas parameters indicated that no decrease in digestion and stability occurred at the highest C/N ratio. Chemical oxygen demand (COD) removal averaged 88%, while volatile fatty acids were maintained at a low level (< 500 mg l–1). Biogas yield averaged 0·423 m3kg–1COD and the methane content of the biogas varied between 57 and 63%. Ammonia toxicity occurred at a C/N ratio of 7/5 in the substrate feed. Virtually no ammonia N was detected in the effluent when whey substrates with C/N ratios of 50 and 73 were fed. Titration curves showed that buffer intensities in the effluent were not affected by a decrease in ammonia level. A decrease in the biomass content of the effluent which occurred as a result of the increase in C/N ratio of the substrate did not cause any rate limiting effect on biogas production. The removal of protein from the whey caused a reduction in the ratio of COD: total carbon in the whey. On average 59% of the carbon in the substrate was converted to biogas.

scholarly journals Improving anaerobic conversion of pulp mill secondary sludge to biogas by pretreatment

TAPPI Journal ◽  
2010 ◽  
Vol 9 (6) ◽  
pp. 16-21 ◽  
Author(s):  
NICHOLAS WOOD ◽  
HONGHI TRAN ◽  
EMMA MASTER
Keyword(s):  
Anaerobic Digestion ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Pulp Mill ◽  
Thermal Pretreatment ◽  
Digestion Rate ◽  
Biogas Yield ◽  
Secondary Sludge ◽  
Kraft Mill ◽  
Anaerobic Conversion

We examined the effectiveness of thermal, caustic, and sonication pretreatment methods in improving anaerobic conversion to biogas of secondary sludge samples obtained from a kraft mill and a sulfite mill. All three methods improved the anaerobic digestion rate and the biogas yield of the sludge samples. Thermal pretreatment was the most effective, followed closely by caustic pretreatment, and sonication the least. The total biogas productions per unit of chemical oxygen demand of sulfite sludge and kraft sludge samples were respectively 1.2 and 3 times higher with pretreatments than without. Also, the biogas production from the untreated sulfite mill sludge was 4 times higher than that from the untreated kraft mill sludge.

scholarly journals Effect Of Alkaline Pre-Treatment On Cassava Pulp For Optimum Biogas Production

2019 ◽  
Vol 8 (2) ◽  
pp. 5919-5923
Keyword(s):  
Chemical Oxygen Demand ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Oxygen Demand ◽  
Treatment Method ◽  
Batch Mode ◽  
Biogas Yield ◽  
Cassava Pulp ◽  
Soluble Chemical Oxygen Demand ◽  
Pre Treatment

(Being produced in vast quantity as one of by-product from cassava starch processing chains, cassava pulp has great potential for energy recovery by harnessing biogas through anaerobic digestion (AD). This study aims to enhance biogas production by comparative investigation in batch mode digestion. 5%TS w/v of cassava pulp mixed with mill effluent were pre-treated with 10 molar potassium hydroxide (KOH), sodium hydroxide (NaOH), and calcium hydroxide (Ca(OH)2) solution for 6 hours contact time. Effects of different alkaline pre-treatment on cassava substrate were assessed in total dissolved solid (TDS), soluble chemical oxygen demand (SCOD), Volatile Fatty Acids to Alkalinity ratio (VFA/TA), and reducing sugars. Daily accumulated biogas yield was taken as final indicator of the effect of different pre-treatment. KOH pre-treatment in pH 11 resulted highest dissolved solid 13.07 mg/L, and improved soluble chemical oxygen demand (SCOD) formation up to 75.61% (480,000 mg/L) than control substrate. The experiment revealed peak biogas production by KOH pre-treated substrate was found at day 6 after digestion executed, and achieved 546 ml. The finding proves out of different pre-treatment method applicable to cassava pulp, KOH pre-treatment could realistically increase biogas yield for cassava mills. Biogas production increased up to 101%, 92%, and 70% using KOH, Ca(OH)2 and NaOH respectively. However, when future provision to the technology for AD system and design is concerned, the choice of highly reactive alkali could lead to complication in the system.

scholarly journals Use of Confectionery Waste in Biogas Production by the Anaerobic Digestion Process

Molecules ◽  
2018 ◽  
Vol 24 (1) ◽  
pp. 37 ◽  
Author(s):  
Agnieszka A. Pilarska ◽  
Krzysztof Pilarski ◽  
Agnieszka Wolna-Maruwka ◽  
Piotr Boniecki ◽  
Maciej Zaborowicz
Keyword(s):  
Anaerobic Digestion ◽  
Volatile Fatty Acids ◽  
Biogas Production ◽  
Test Material ◽  
Biochemical Methane Potential ◽  
Biogas Yield ◽  
Ph Values ◽  
Chemical Equations ◽  
Biogas Plants ◽  
Methane Potential

It was the objective of this study to verify the efficiency and stability of anaerobic digestion (AD) for selected confectionery waste, including chocolate bars (CB), wafers (W), and filled wafers (FW), by inoculation with digested cattle slurry and maize silage pulp. Information in the literature on biogas yield for these materials and on their usefulness as substrate in biogas plants remains to be scarce. Owing to its chemical structure, including the significant content of carbon-rich carbohydrates and fat, the confectionery waste has a high biomethane potential. An analysis of the AD process indicates differences in the fluctuations of the pH values of three test samples. In comparison with W and FW, CB tended to show slightly more reduced pH values in the first step of the process; moreover an increase in the content of volatile fatty acids (VFA) was recorded. In the case of FW, the biogas production process showed the highest stability. Differences in the decomposition dynamics for the three types of test waste were accounted for by their different carbohydrate contents and also different biodegradabilities of specific compounds. The highest efficiency of the AD process was obtained for the filled wafers, where the biogas volumes, including methane, were 684.79 m3 Mg−1 VS and 506.32 m3 Mg−1 VS, respectively. A comparable volume of biogas (673.48 m3 Mg−1 VS) and a lower volume of methane (407.46 m3 Mg−1 VS) were obtained for chocolate bars. The lowest volumes among the three test material types, i.e., 496.78 m3 Mg−1 VS (biogas) and 317.42 m3 Mg−1 VS (methane), were obtained for wafers. This article also proposes a method of estimation of the biochemical methane potential (theoretical BMP) based on the chemical equations of degradation of sugar, fats, and proteins and known biochemical composition (expressed in grams).

Sign in / Sign up

Export Citation Format

Share Document