scholarly journals The Influence of Boundary Layer Caused by Riblets on the Aircraft Surface

2020 ◽  
Vol 10 (11) ◽  
pp. 3686
Author(s):  
Hongqing Lv ◽  
Zhenqing Wang ◽  
Jiahao Chen ◽  
Lei Xu
Keyword(s):  
Boundary Layer ◽  
Drag Reduction ◽  
Flow Direction ◽  
Angle Of Attack ◽  
Suction Side ◽  
Aerodynamic Characteristics ◽  
Wall Surface ◽  
Friction Resistance ◽  
Naca0012 Airfoil ◽  
Stall Angle

Drag reduction of riblets is one of the most important problems in drag reduction of non-smooth surfaces. In the past two decades, the use of riblets arranged along the flow direction to reduce frictional resistance has received considerable attention. In this paper, we study the plates with the triangular concave grooves, triangular protrusion riblets, trapezoidal concave grooves, trapezoidal protrusion riblets, and circular concave grooves. The numerical simulation method is used to calculate five kinds of plates with grooves and riblets under multiple working conditions. The results showed that the plates with grooves and riblets generated vortices inside the grooves, which separated the incoming flow from the wall surface, and by increasing the thickness of the boundary layer, greatly reducing the average velocity gradient of the wall surface, compared with the smooth flat plate, the friction resistance is reduced. But, lateral riblets and grooves cause additional pressure resistance, which is one order of magnitude higher than the friction resistance. Then, the triangular concave grooves are arranged on the suction and pressure sides of the NACA0012 airfoil, respectively. We calculated the aerodynamic parameters of the both airfoils, and the standard NACA0012 airfoil from the −8° attack angle to their respective stall attack angles. The results showed that the NACA0012 airfoil with triangular concave grooves on the suction side reduced the aerodynamic characteristics of the standard NACA0012 at a small angle of attack, but the stall angle of attack of the standard NACA0012 airfoil was improved, because the grooves ensure that some gas can flow normally on the suction side and delay the separation of the boundary layer. The NACA0012 airfoil with triangular concave grooves on the pressure side did not effectively improve the aerodynamic characteristics: lift–drag ratio decreased and stall angle of attack decreased, but it can increase the lift slightly.

Numerical Investigation of Flow past a Wavy Airfoil

2011 ◽  
Vol 110-116 ◽  
pp. 4269-4275
Author(s):  
K. Lam ◽  
Y.F. Lin ◽  
Y. Liu ◽  
L. Zou
Keyword(s):  
Numerical Investigation ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Large Eddy Simulations ◽  
Wavy Surface ◽  
Naca0012 Airfoil ◽  
Large Eddy ◽  
Stall Angle ◽  
Coefficient Reduction

The effect of the wavy surface on the aerodynamic characteristics of an airfoil is studied using the large eddy simulations. A more gentle lift characteristic is obtained during stall. For angles of attack less than the baseline stall angle of a NACA0012 airfoil, a lift coefficient reduction was observed for the wavy airfoils, while the lift coefficient increases up to 23% greater than that of a NACA0012 airfoil when the angle of attack is larger than the baseline stall angle of the NACA0012 airfoil.

scholarly journals Experimental Investigation of Lift Enhancement and Drag Reduction of Discrete Co-Flow Jet Rotor Airfoil

2021 ◽  
Vol 11 (20) ◽  
pp. 9561
Author(s):  
Shunlei Zhang ◽  
Xudong Yang ◽  
Bifeng Song ◽  
Zhuoyuan Li ◽  
Bo Wang
Keyword(s):  
Drag Reduction ◽  
High Performance ◽  
Performance Enhancement ◽  
Fundamental Problem ◽  
Unit Length ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Relative Unit ◽  
Lift Enhancement ◽  
Stall Angle

Rotor airfoil design involves multi-point and multi-objective complex constraints. How to significantly improve the maximum lift coefficient and lift-to-drag ratio of rotor airfoil is a fundamental problem, which should be solved urgently in the development of high-performance helicopter rotor blades. To address this, discrete co-flow jet (DCFJ) technology is one methods with the most potential that can be harnessed to improve the performance of the rotor airfoil. In this study, wind tunnel experiments are conducted to study the effect of DCFJ technology on lift enhancement and drag reduction of OA312 airfoil. Furthermore, the performance improvement effects of the open co-flow jet (CFJ) and DCFJ technologies are studied. In addition, the influence of fundamental parameters, such as the obstruction factor and relative unit length, are analyzed. Results demonstrate that DCFJ technology is better than CFJ technology on the performance enhancement of the OA312 airfoil. Moreover, the DCFJ rotor airfoil can significantly reduce the drag coefficient and increase the maximum lift coefficient and the stall angle of attack. The maximum lift coefficient can be increased by nearly 67.3%, and the stall angle of attack can be delayed by about 12°. The DCFJ rotor airfoil can achieve the optimal performance when the obstruction factor is 1/2 and the relative unit length is 0.025.

The Effect of Airfoil Shape on Trailing Edge Noise

2019 ◽  
Vol 27 (02) ◽  
pp. 1850020 ◽  
Author(s):  
Seongkyu Lee
Keyword(s):  
Boundary Layer ◽  
Noise Source ◽  
Source Region ◽  
Low Frequency ◽  
Suction Side ◽  
Frequency Noise ◽  
Pressure Side ◽  
Trailing Edge ◽  
Trailing Edge Noise ◽  
Naca0012 Airfoil

This paper investigates the effect of airfoil shape on trailing edge noise. The boundary layer profiles are obtained by XFOIL and the trailing edge noise is predicted by a TNO semi-empirical model. In order to investigate the noise source characteristics, the wall pressure spectrum is decomposed into three components. This decomposition helps in finding the dominant source region and the peak noise frequency for each airfoil. The method is validated for a NACA0012 airfoil, and then five additional wind turbine airfoils are examined: NACA0018, DU96-w-180, S809, S822 and S831. It is found that the dominant source region is around 40% of the boundary layer thickness for both the suction and pressure sides for a NACA0012 airfoil. As airfoil thickness and camber increase, the maximum source region moves slightly upward on the suction side. However, the effect of the airfoil shape on the maximum source region on the pressure side is negligible, except for the S831 airfoil, which exhibits an extension of the noise source region near the wall at high frequencies. As airfoil thickness and camber increase, low frequency noise is increased. However, a higher camber reduces low frequency noise on the pressure side. The maximum camber position is also found to be important and its rear position increases noise levels on the suction side.

scholarly journals Experimental and Numerical Analysis of the Effect of Vortex Generator Height on Vortex Characteristics and Airfoil Aerodynamic Performance

Energies ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 959 ◽  
Author(s):  
Xinkai Li ◽  
Ke Yang ◽  
Xiaodong Wang
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Performance ◽  
Average Kinetic Energy ◽  
Control Effect ◽  
Height Range ◽  
Stall Angle ◽  
Drag Ratio

To explore the effect of the height of vortex generators (VGs) on the control effect of boundary-layer flow, the vortex characteristics of a plate and the aerodynamic characteristics of an airfoil for VGs were studied by both wind tunnel experiments and numerical methods. Firstly, the ratio of VG height (H) to boundary layer thickness (δ) was studied on a flat plate boundary layer; the values of H are 0.1δ, 0.2δ, 0.5δ, 1.0δ, 1.5δ, and 2.0δ. Results show that the concentrated vortex intensity and VG height present a logarithmic relationship, and vortex intensity is proportional to the average kinetic energy of the fluid in the height range of the VG. Secondly, the effects of height on the aerodynamic performance of airfoils were studied in a wind tunnel using three VGs with H = 0.66δ, 1.0δ, and 1.33δ. The stall angle of the airfoil with and without VGs is 18° and 8°, respectively, so the VGs increase the stall angle by 10°. The maximum lift coefficient of the airfoil with VGs increases by 48.7% compared with the airfoil without VGs, and the drag coefficient of the airfoil with VGs is 84.9% lower than that of the airfoil without VGs at an angle of attack of 18°. The maximum lift–drag ratio of the airfoil with VGs is lower than that of the airfoil without VGs, so the VGs do not affect the maximum lift–drag ratio of the airfoil. However, a VG does increase the angle of attack of the best lift–drag ratio.

scholarly journals РОЗРАХУНОК АЕРОДИНАМІЧНИХ ХАРАКТЕРИСТИК НАДЗВУКОВИХ ОПЕРЕНИХ ОСЕСИМЕТРИЧНИХ ТІЛ ОБЕРТАННЯ

2019 ◽  
pp. 4-17
Author(s):  
Олександр Миколайович Шийко ◽  
Анатолій Михайлович Павлюченко ◽  
Андрій Вікторович Скорик ◽  
Олексій Анатолійович Обухов ◽  
Ігор Володимирович Коплик
Keyword(s):  
Numerical Solution ◽  
Stokes Equations ◽  
Aerodynamic Force ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Aerodynamic Coefficients ◽  
Navier Stokes Equations ◽  
Friction Resistance ◽  
Ansys Cfx

The subject of research in the article is the aerodynamic forces arising from the flight of supersonic feathered rotation bodies such as unguided rockets. The aim of the work is to develop a method for calculating the aerodynamic coefficients of the resultant forces and moments of supersonic feathered bodies of revolution such as unguided missiles when flown around at an angle of attack with pre-, trans- and supersonic speeds according to drawings of their external contours. Tasks: using modern software systems and flight experiments, develop a method for calculating the distribution of normal and tangential stresses over the surface of a supersonic feathered body of rotation, their equivalent and aerodynamic coefficients at up-, trans- and supersonic flow velocities at an angle of attack. The applied methods are the numerical solution of the Navier-Stokes equations, the use of two-parameter differential models of near-wall turbulent viscosity, verification of the methodology by comparing the results of calculations with the data of flight experiments and known data on the aerodynamic resistance of the object of research. The following results were obtained. Based on the numerical solution of the Navier-Stokes equations in the ANSYS CFX software package using the γ-ReΘt SST–model of Menter’s near-wall turbulence, a method is developed for calculating the aerodynamic characteristics of supersonic axially symmetric rotation bodies of uncontrollable missiles according to drawings of the external contours in the presence of a counter-flow angle. Using the developed technique it is possible to calculate the aerodynamic coefficients of friction resistance, pressure resistance and bottom resistance at sub-, trans- and supersonic speeds. Characteristics include the coefficients of the longitudinal aerodynamic force, transverse aerodynamic force, aerodynamic stabilizing moment and the coordinate of the center of pressure of the feathered body of rotation. For the calculations, were applied the external contours of the unguided missile M–21OФ. Calculations were performed for the counter-flow Mach numbers within0,1 £ M∞ £ 2,5. The aerodynamic coefficients were calculated as functions of the Mach number M∞. In order to determine the Reynolds number of the beginning of the laminar-turbulent transition in the boundary layer for this type of aircraft the characteristics of the friction resistance were calculated and compared with the flight data for two samples of research aerophysical complexes. Conclusions. The scientific novelty of the results is as follows: a pilot test was created and involved the results of flight experiments on Reynolds numbers of the start of a laminar-turbulent transition in the boundary layers of a method for calculating the aerodynamic drag coefficients of supersonic axially rotated bodies of rotation like uncontrollable missiles according to the drawings of their external contours during turning angle of attack based on the numerical solution of the Reynolds-averaged Navier-Stokes equations in the framework of the programme product ANSYS CFX using γ-ReΘt SST–Menter turbulence model. Verification of the calculation results was carried out on the basis of their comparison with the known values of the aerodynamic characteristics of the object of research with the axisymmetric flow.

scholarly journals Investigation of a NACA0012 Finite Wing Aerodynamics at Low Reynold’s Numbers and 0º to 90º Angle of Attack

2019 ◽  
Author(s):  
Shahrooz Eftekhari ◽  
Abdulkareem Shafiq Mahdi Al-Obaidi
Keyword(s):  
Drag Force ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Poor Performance ◽  
Aerodynamic Characteristics ◽  
Airfoil Surface ◽  
Wing Geometry ◽  
Stall Angle ◽  
Finite Wing ◽  
Lift And Drag

The aerodynamic characteristics of a NACA0012 wing geometry at low Reynold’s numbers and angle of attack ranging from 0º to 90º are investigated using numerical simulations and the results are validated by wind tunnel experiments. Further experiments are conducted at low Reynold’s numbers of 1 × 105, 2 × 105 and 3 × 105. Findings of the study show a similar trend for the lift and drag coefficients at all the investigated Reynold’s numbers. The lift coefficient is linearly increased with angle of attack until it reaches its maximum value at 32º which is the stall angle. It is observed that further increment in angle of attack results in decrement of lift coefficient until it reaches its minimum value at 90º angle of attack. The drag force acting on the airfoil increases as the angle of attack is increased and increment in the drag force results in change of laminar flow to turbulent flow. As the turbulence gets higher the flow starts to separate from the airfoil surface due to eddies generated by turbulence. Hence, the lift force generated by the wing is reduced and drag force is increased simultaneously, which results in poor performance of the wing.

Sign in / Sign up

Export Citation Format

Share Document