scholarly journals Experimental Investigation of Lift Enhancement and Drag Reduction of Discrete Co-Flow Jet Rotor Airfoil

2021 ◽  
Vol 11 (20) ◽  
pp. 9561
Author(s):  
Shunlei Zhang ◽  
Xudong Yang ◽  
Bifeng Song ◽  
Zhuoyuan Li ◽  
Bo Wang
Keyword(s):  
Drag Reduction ◽  
High Performance ◽  
Performance Enhancement ◽  
Fundamental Problem ◽  
Unit Length ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Relative Unit ◽  
Lift Enhancement ◽  
Stall Angle

Rotor airfoil design involves multi-point and multi-objective complex constraints. How to significantly improve the maximum lift coefficient and lift-to-drag ratio of rotor airfoil is a fundamental problem, which should be solved urgently in the development of high-performance helicopter rotor blades. To address this, discrete co-flow jet (DCFJ) technology is one methods with the most potential that can be harnessed to improve the performance of the rotor airfoil. In this study, wind tunnel experiments are conducted to study the effect of DCFJ technology on lift enhancement and drag reduction of OA312 airfoil. Furthermore, the performance improvement effects of the open co-flow jet (CFJ) and DCFJ technologies are studied. In addition, the influence of fundamental parameters, such as the obstruction factor and relative unit length, are analyzed. Results demonstrate that DCFJ technology is better than CFJ technology on the performance enhancement of the OA312 airfoil. Moreover, the DCFJ rotor airfoil can significantly reduce the drag coefficient and increase the maximum lift coefficient and the stall angle of attack. The maximum lift coefficient can be increased by nearly 67.3%, and the stall angle of attack can be delayed by about 12°. The DCFJ rotor airfoil can achieve the optimal performance when the obstruction factor is 1/2 and the relative unit length is 0.025.

scholarly journals Design and Validation of a New Morphing Camber System by Testing in the Price—Païdoussis Subsonic Wind Tunnel

Aerospace ◽  
2020 ◽  
Vol 7 (3) ◽  
pp. 23 ◽  
Author(s):  
David Communier ◽  
Ruxandra Mihaela Botez ◽  
Tony Wong
Keyword(s):  
Wind Tunnel ◽  
Unmanned Aerial Vehicle ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Trailing Edge ◽  
Subsonic Wind Tunnel ◽  
Aerial Vehicle ◽  
Stall Angle

This paper presents the design and wind tunnel testing of a morphing camber system and an estimation of performances on an unmanned aerial vehicle. The morphing camber system is a combination of two subsystems: the morphing trailing edge and the morphing leading edge. Results of the present study show that the aerodynamics effects of the two subsystems are combined, without interfering with each other on the wing. The morphing camber system acts only on the lift coefficient at a 0° angle of attack when morphing the trailing edge, and only on the stall angle when morphing the leading edge. The behavior of the aerodynamics performances from the MTE and the MLE should allow individual control of the morphing camber trailing and leading edges. The estimation of the performances of the morphing camber on an unmanned aerial vehicle indicates that the morphing of the camber allows a drag reduction. This result is due to the smaller angle of attack needed for an unmanned aerial vehicle equipped with the morphing camber system than an unmanned aerial vehicle equipped with classical aileron. In the case study, the morphing camber system was found to allow a reduction of the drag when the lift coefficient was higher than 0.48.

scholarly journals Effects of Geometrical Parameters of Internal Blown Flap and Its Optimal Design

2020 ◽  
Vol 38 (1) ◽  
pp. 58-67
Author(s):  
Rui Liu ◽  
Junqiang Bai ◽  
Yasong Qiu ◽  
Guozhu Gao
Keyword(s):  
Optimal Design ◽  
Design Method ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Chord Length ◽  
Geometrical Parameters ◽  
Design Constraint ◽  
Design Variables ◽  
Flap Deflection ◽  
Stall Angle

The internal blown flap was numerically simulated. Firstly, a parameterization method was developed, which can properly describe the shape of the internal blown flap according to such geometrical parameters as flap chord length, flap deflection, height of blowing slot and its position. Then the reliability of the numerical simulation was validated through comparing the pressure distribution of the CC020-010EJ fundamental generic circulation control airfoil with the computational results and available experiment results. The effects of the geometrical parameters on the aerodynamic performance of the internal blown flap was investigated. The investigation results show that the lift coefficient increases with the increase of flap chord length and flap deflection angle and with the decrease of height of blowing slot and its front position. Lastly, a method of optimal design of the geometrical parameters of the internal blown flap was developed. The design variables include flap chord length, flap deflection, height of blowing slot and its position. The optimal design is based on maximum lift coefficient, the angle of attack of 5 degrees and the design constraint of stall angle of attack of less than 9 degrees. The optimization results show that the optimal design method can apparently raise the lift coefficient of an internal blown flap up to 1.7.

scholarly journals The Influence of Boundary Layer Caused by Riblets on the Aircraft Surface

2020 ◽  
Vol 10 (11) ◽  
pp. 3686
Author(s):  
Hongqing Lv ◽  
Zhenqing Wang ◽  
Jiahao Chen ◽  
Lei Xu
Keyword(s):  
Boundary Layer ◽  
Drag Reduction ◽  
Flow Direction ◽  
Angle Of Attack ◽  
Suction Side ◽  
Aerodynamic Characteristics ◽  
Wall Surface ◽  
Friction Resistance ◽  
Naca0012 Airfoil ◽  
Stall Angle

Drag reduction of riblets is one of the most important problems in drag reduction of non-smooth surfaces. In the past two decades, the use of riblets arranged along the flow direction to reduce frictional resistance has received considerable attention. In this paper, we study the plates with the triangular concave grooves, triangular protrusion riblets, trapezoidal concave grooves, trapezoidal protrusion riblets, and circular concave grooves. The numerical simulation method is used to calculate five kinds of plates with grooves and riblets under multiple working conditions. The results showed that the plates with grooves and riblets generated vortices inside the grooves, which separated the incoming flow from the wall surface, and by increasing the thickness of the boundary layer, greatly reducing the average velocity gradient of the wall surface, compared with the smooth flat plate, the friction resistance is reduced. But, lateral riblets and grooves cause additional pressure resistance, which is one order of magnitude higher than the friction resistance. Then, the triangular concave grooves are arranged on the suction and pressure sides of the NACA0012 airfoil, respectively. We calculated the aerodynamic parameters of the both airfoils, and the standard NACA0012 airfoil from the −8° attack angle to their respective stall attack angles. The results showed that the NACA0012 airfoil with triangular concave grooves on the suction side reduced the aerodynamic characteristics of the standard NACA0012 at a small angle of attack, but the stall angle of attack of the standard NACA0012 airfoil was improved, because the grooves ensure that some gas can flow normally on the suction side and delay the separation of the boundary layer. The NACA0012 airfoil with triangular concave grooves on the pressure side did not effectively improve the aerodynamic characteristics: lift–drag ratio decreased and stall angle of attack decreased, but it can increase the lift slightly.

Experimental investigations on the application of lift enhancement devices to forward-swept aircraft model

2006 ◽  
Vol 110 (1108) ◽  
pp. 361-367 ◽  
Author(s):  
W. Zhang ◽  
J. J. Wang ◽  
Z. Wu
Keyword(s):  
Lift Coefficient ◽  
Experimental Investigations ◽  
Aircraft Model ◽  
High Side ◽  
Gurney Flap ◽  
Lift Enhancement ◽  
Stall Angle ◽  
Lift And Drag ◽  
Low Speed Wind Tunnel ◽  
Wing Tip

Abstract The force measurements were conducted in low speed wind tunnel to investigate the effects of the scale, shape and the installation type of Gurney flap on a forward-swept aircraft model. The results indicated that both rectangular and triangular Gurney flaps can enhance the lift coefficient of the model tested, but with a little decrease of stall angle from 38° to 36°. The lift and drag coefficients increased with the Gurney flap scales. Meanwhile, the triangular Gurney flap can improve the aerodynamic performance more effectively when its high side is located near the wing root than the reverse installation with the low side near the wing root and the high side near the wing tip. Additionally, for the same Gurney flap, the model with smaller forward-swept angle can generate higher lift-enhancement in comparison with the larger forward-swept angle model.

scholarly journals The control of flight force by a flapping wing: lift and drag production

2001 ◽  
Vol 204 (15) ◽  
pp. 2607-2626 ◽  
Author(s):  
Sanjay P. Sane ◽  
Michael H. Dickinson
Keyword(s):  
High Performance ◽  
Time Course ◽  
Aerodynamic Force ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Force Sensor ◽  
Aerodynamic Forces ◽  
Wing Kinematics ◽  
The Mean ◽  
Stroke Amplitude

SUMMARYWe used a dynamically scaled mechanical model of the fruit fly Drosophila melanogaster to study how changes in wing kinematics influence the production of unsteady aerodynamic forces in insect flight. We examined 191 separate sets of kinematic patterns that differed with respect to stroke amplitude, angle of attack, flip timing, flip duration and the shape and magnitude of stroke deviation. Instantaneous aerodynamic forces were measured using a two-dimensional force sensor mounted at the base of the wing. The influence of unsteady rotational effects was assessed by comparing the time course of measured forces with that of corresponding translational quasi-steady estimates. For each pattern, we also calculated mean stroke-averaged values of the force coefficients and an estimate of profile power. The results of this analysis may be divided into four main points.(i) For a short, symmetrical wing flip, mean lift was optimized by a stroke amplitude of 180° and an angle of attack of 50°. At all stroke amplitudes, mean drag increased monotonically with increasing angle of attack. Translational quasi-steady predictions better matched the measured values at high stroke amplitude than at low stroke amplitude. This discrepancy was due to the increasing importance of rotational mechanisms in kinematic patterns with low stroke amplitude.(ii) For a 180° stroke amplitude and a 45° angle of attack, lift was maximized by short-duration flips occurring just slightly in advance of stroke reversal. Symmetrical rotations produced similarly high performance. Wing rotation that occurred after stroke reversal, however, produced very low mean lift.(iii) The production of aerodynamic forces was sensitive to changes in the magnitude of the wing’s deviation from the mean stroke plane (stroke deviation) as well as to the actual shape of the wing tip trajectory. However, in all examples, stroke deviation lowered aerodynamic performance relative to the no deviation case. This attenuation was due, in part, to a trade-off between lift and a radially directed component of total aerodynamic force. Thus, while we found no evidence that stroke deviation can augment lift, it nevertheless may be used to modulate forces on the two wings. Thus, insects might use such changes in wing kinematics during steering maneuvers to generate appropriate force moments.(iv) While quasi-steady estimates failed to capture the time course of measured lift for nearly all kinematic patterns, they did predict with reasonable accuracy stroke-averaged values for the mean lift coefficient. However, quasi-steady estimates grossly underestimated the magnitude of the mean drag coefficient under all conditions. This discrepancy was due to the contribution of rotational effects that steady-state estimates do not capture. This result suggests that many prior estimates of mechanical power based on wing kinematics may have been grossly underestimated.

scholarly journals Effect of Reynolds Number on Aerodynamics of Airfoil with Gurney Flap

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Shubham Jain ◽  
Nekkanti Sitaram ◽  
Sriram Krishnaswamy
Keyword(s):  
Reynolds Number ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Critical Range ◽  
Gurney Flap ◽  
Stall Angle ◽  
Lift And Drag ◽  
Naca 0012

Steady state, two-dimensional computational investigations performed on NACA 0012 airfoil to analyze the effect of variation in Reynolds number on the aerodynamics of the airfoil without and with a Gurney flap of height of 3% chord are presented in this paper. RANS based one-equation Spalart-Allmaras model is used for the computations. Both lift and drag coefficients increase with Gurney flap compared to those without Gurney flap at all Reynolds numbers at all angles of attack. The zero lift angle of attack seems to become more negative as Reynolds number increases due to effective increase of the airfoil camber. However the stall angle of attack decreased by 2° for the airfoil with Gurney flap. Lift coefficient decreases rapidly and drag coefficient increases rapidly when Reynolds number is decreased below critical range. This occurs due to change in flow pattern near Gurney flap at low Reynolds numbers.

Numerical Investigation of Flow past a Wavy Airfoil

2011 ◽  
Vol 110-116 ◽  
pp. 4269-4275
Author(s):  
K. Lam ◽  
Y.F. Lin ◽  
Y. Liu ◽  
L. Zou
Keyword(s):  
Numerical Investigation ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Large Eddy Simulations ◽  
Wavy Surface ◽  
Naca0012 Airfoil ◽  
Large Eddy ◽  
Stall Angle ◽  
Coefficient Reduction

The effect of the wavy surface on the aerodynamic characteristics of an airfoil is studied using the large eddy simulations. A more gentle lift characteristic is obtained during stall. For angles of attack less than the baseline stall angle of a NACA0012 airfoil, a lift coefficient reduction was observed for the wavy airfoils, while the lift coefficient increases up to 23% greater than that of a NACA0012 airfoil when the angle of attack is larger than the baseline stall angle of the NACA0012 airfoil.

The Aerodynamics Investigation of Vortex Trap on Helicopter Blade

2012 ◽  
Vol 225 ◽  
pp. 43-48
Author(s):  
M.F. Yaakub ◽  
A.A. Wahab ◽  
Mohammad Fahmi Abdul Ghafir ◽  
Siti Nur Mariani Mohd Yunos ◽  
Siti Juita Mastura Mohd Salleh ◽  
...  
Keyword(s):  
Lift Force ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Strong Wind ◽  
High Angle ◽  
Forward Flight ◽  
High Angle Of Attack ◽  
Helicopter Blade ◽  
Stall Angle ◽  
Cfd Analyses

During helicopter forward flight, the retreating blade revolves at high angle of attack compared to advancing blade in order to balance the lift and also to stabilise the helicopter. However, due to the aerodynamics limitations of the retreating blade at forward flight, stall may occur at high angle of attack compared with the advancing blade. This phenomenon is dangerous for pilot when controlling and balancing the helicopter while flying against strong wind. This paper investigates the capabilities of introducing multiple vortex traps on the upper surface of the helicopter airfoil in order to delay the stall angle of retreating helicopter blade. Blade Element Theory (BET) was applied to scrutinize the lift force along the helicopter blade. Computational Fluid Dynamic (CFD) analyses using the Shear-Stress Transport (SST) turbulence model was carried out to investigate the effect of groove on delaying the stall and to predict the separation of flow over the airfoil. Based on the CFD analyses, the optimization of the groove was done by analyzing the numbers and locations of the grooves. Finally, the results from both BET and the CFD analyses were utilised to obtain the lift force achieved by the vortex trap. The study showed that the presence of multiple vortex traps has successfully increased the lift coefficient and most importantly, delaying the stall angle.

scholarly journals Experimental and Numerical Analysis of the Effect of Vortex Generator Height on Vortex Characteristics and Airfoil Aerodynamic Performance

Energies ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 959 ◽  
Author(s):  
Xinkai Li ◽  
Ke Yang ◽  
Xiaodong Wang
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Performance ◽  
Average Kinetic Energy ◽  
Control Effect ◽  
Height Range ◽  
Stall Angle ◽  
Drag Ratio

To explore the effect of the height of vortex generators (VGs) on the control effect of boundary-layer flow, the vortex characteristics of a plate and the aerodynamic characteristics of an airfoil for VGs were studied by both wind tunnel experiments and numerical methods. Firstly, the ratio of VG height (H) to boundary layer thickness (δ) was studied on a flat plate boundary layer; the values of H are 0.1δ, 0.2δ, 0.5δ, 1.0δ, 1.5δ, and 2.0δ. Results show that the concentrated vortex intensity and VG height present a logarithmic relationship, and vortex intensity is proportional to the average kinetic energy of the fluid in the height range of the VG. Secondly, the effects of height on the aerodynamic performance of airfoils were studied in a wind tunnel using three VGs with H = 0.66δ, 1.0δ, and 1.33δ. The stall angle of the airfoil with and without VGs is 18° and 8°, respectively, so the VGs increase the stall angle by 10°. The maximum lift coefficient of the airfoil with VGs increases by 48.7% compared with the airfoil without VGs, and the drag coefficient of the airfoil with VGs is 84.9% lower than that of the airfoil without VGs at an angle of attack of 18°. The maximum lift–drag ratio of the airfoil with VGs is lower than that of the airfoil without VGs, so the VGs do not affect the maximum lift–drag ratio of the airfoil. However, a VG does increase the angle of attack of the best lift–drag ratio.

scholarly journals SDRE and LQR Controls Comparison Applied in High-Performance Aircraft in a Longitudinal Flight

2021 ◽  
Vol 1 (2) ◽  
pp. 131-144
Author(s):  
Guilherme P. Dos Santos ◽  
Adriano Kossoski ◽  
Jose M. Balthazar ◽  
Angelo Marcelo Tusset
Keyword(s):  
Nonlinear Model ◽  
Flight Control ◽  
High Performance ◽  
Large Range ◽  
Angle Of Attack ◽  
Linear Quadratic Regulator ◽  
Linear Quadratic ◽  
State Dependent ◽  
Stall Angle ◽  
Difficult Situations

This paper presents the design of the LQR (Linear Quadratic Regulator) and SDRE (State-Dependent Riccati Equation) controllers for the flight control of the F-8 Crusader aircraft considering the nonlinear model of longitudinal movement of the aircraft.  Numerical results and analysis demonstrate that the designed controllers can lead to significant improvements in the aircraft's performance, ensuring stability in a large range of attack angle situations. When applied in flight conditions with an angle of attack above the stall situation and influenced by the gust model, it was demonstrated that the LQR and SDRE controllers were able to smooth the flight response maintaining conditions in balance for an angle of attack up to 56% above stall angle.  However, for even more difficult situations, with angles of attack up to 76% above the stall angle, only the SDRE controller proved to be efficient and reliable in recovering the aircraft to its stable flight configuration.

Sign in / Sign up

Export Citation Format

Share Document