scholarly journals Analysis of the Effect of Shape Factor on Cork–Rubber Composites under Small Strain Compression

2020 ◽  
Vol 10 (20) ◽  
pp. 7177
Author(s):  
Helena Lopes ◽  
Susana Silva ◽  
José Machado
Keyword(s):  
Finite Element Analysis ◽  
Cross Section ◽  
Shape Factor ◽  
Small Strain ◽  
Compression Tests ◽  
Rubber Composites ◽  
Element Analysis ◽  
Rubber Material ◽  
Small Strains ◽  
Good Agreement

Like other types of elastomers, different geometries of the same cork–rubber material present different mechanical behaviour when subject to compression between bonded plates. To validate the application of Hooke’s Law on cork–rubber materials, under compression at small strains, a set of experimental and numerical analyses has been conducted. Using finite element analysis, a methodology is described to relate frictionless and frictional compression between a cork–rubber sample and loading plates. Based on that, the performance of square cross-section blocks with other dimensions can be evaluated. The results obtained by this approach showed a good agreement with experimental compression tests and with outputs from other models available in the literature relating Young and apparent compression moduli.

Computer Modeling of a Tire under Cornering Loads

1989 ◽  
Vol 17 (2) ◽  
pp. 86-99 ◽  
Author(s):  
I. Gardner ◽  
M. Theves
Keyword(s):  
Finite Element Analysis ◽  
Geometric Approach ◽  
Lateral Force ◽  
Slip Angle ◽  
Element Analysis ◽  
Pressure Distributions ◽  
Slip Effects ◽  
Improved Accuracy ◽  
Nonlinear Geometric ◽  
Good Agreement

Abstract During a cornering maneuver by a vehicle, high forces are exerted on the tire's footprint and in the contact zone between the tire and the rim. To optimize the design of these components, a method is presented whereby the forces at the tire-rim interface and between the tire and roadway may be predicted using finite element analysis. The cornering tire is modeled quasi-statically using a nonlinear geometric approach, with a lateral force and a slip angle applied to the spindle of the wheel to simulate the cornering loads. These values were obtained experimentally from a force and moment machine. This procedure avoids the need for a costly dynamic analysis. Good agreement was obtained with experimental results for self-aligning torque, giving confidence in the results obtained in the tire footprint and at the rim. The model allows prediction of the geometry and of the pressure distributions in the footprint, since friction and slip effects in this area were considered. The model lends itself to further refinement for improved accuracy and additional applications.

Design Research of Steel Pipe Combination of Angle Steel Tower of XiYue 220kV Cross Section

2013 ◽  
Vol 470 ◽  
pp. 408-411 ◽  
Author(s):  
Yan Zhong Ju ◽  
Xiao Xu Fu ◽  
Neng Xian Zeng
Keyword(s):  
Finite Element Analysis ◽  
Cross Section ◽  
Design Research ◽  
Axial Stress ◽  
Steel Pipe ◽  
Stress Difference ◽  
Analysis Software ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Angle Steel

Given the path situation of Xiyue substation 220kV four outlets project crossing Shunde waterway section,this article applies of Dao Heng tower full stress analysis software and the finite element analysis software ANSYS to two steel pipe combination of angle steel towers to carry on design research,contrast axial stress of two kinds of software,analyse the reasons of axial stress difference.

Finite Element Analysis for the Collapse Accident of a 110kV Transmission Tower

2014 ◽  
Vol 986-987 ◽  
pp. 927-930
Author(s):  
Yi Zhu ◽  
Bo Li ◽  
Hao Wang ◽  
Kun Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cross Section ◽  
Strong Wind ◽  
Transmission Tower ◽  
Element Analysis ◽  
Straight Line ◽  
The Finite Element Analysis

Put the finite element analysis of line tower coupling modeling to the collapse of a 110 kV line straight-line tower, study the effect of strong wind on transmission tower and wire. The results show that under the action of strong wind, the material specification selected by the part of the rods on the type of tower is lower, cross section is smaller, the principal material of tower will be instable and flexional under the compression, resulting in tower collapsed.

Burst Pressure of Pressurized Cylinders With Hillside Nozzle

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
H. F. Wang ◽  
Z. F. Sang ◽  
L. P. Xue ◽  
G. E. O. Widera
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Experimental Models ◽  
Burst Pressure ◽  
Element Analysis ◽  
Test Models ◽  
Scale Test ◽  
Failure Location ◽  
Dimensional Instability ◽  
Good Agreement

The burst pressure of cylinders with hillside nozzle is determined using both experimental and finite element analysis (FEA) approaches. Three full-scale test models with different angles of the hillside nozzle were designed and fabricated specifically for a hydrostatic test in which the cylinders were pressurized with water. 3D static nonlinear finite element simulations of the experimental models were performed to obtain the burst pressures. The burst pressure is defined as the internal pressure for which the structure approaches dimensional instability, i.e., unbounded strain for a small increment in pressure. Good agreement between the predicted and measured burst pressures shows that elastic-plastic finite element analysis is a viable option to estimate the burst pressure of the cylinders with hillside nozzles. The preliminary results also suggest that the failure location is near the longitudinal plane of the cylinder-nozzle intersection and that the burst pressure increases slightly with an increment in the angle of the hillside nozzle.

Finite Element Analysis for Shock Resistance Evaluation of Cushion-Packaged Multifunction Printer Considering Internal Modules

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Se-Chang Kim ◽  
Dae-Geun Cho ◽  
Tae-Gyu Kim ◽  
Se-Hun Jung ◽  
Ja-Choon Koo ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shock Acceleration ◽  
External Shocks ◽  
Compression Tests ◽  
Element Analysis ◽  
Dynamic Behaviors ◽  
Shock Resistance ◽  
The Impact ◽  
Multifunction Printer

Failures in IT electronics are often caused by falling or external shocks during transportation. These failures cause customers to mistrust the reliability of the products. Many manufacturers of IT electronics have not only used cushioning materials but also increased the shock resistance of their products for failure prevention. Especially in case of printer products, the design of the packaging and the product robustness are extremely important because of their substantial weight and the fragility of the internal modules. For product design, it is essential to understand the impact failure mechanism of the products. In this study, a compression test, a drop impact test, and a finite element analysis (FEA) were performed to analyze the dynamic behaviors of a packaged multifunction printer (MFP). The mechanical properties of a cushioning material were measured by compression tests. The FE models of the cushion packaging and the MFP included the physical characteristics of the internal modules, and their dynamic behaviors were obtained using the commercial software ls-dyna3d. Simulation results were also compared with drop test results to verify the proposed FE models. The shock resistance of the MFP was assessed by stress analysis and strength evaluation. We also expect our FE models will be useful for evaluating the fragility of the internal modules because the models can numerically estimate the shock acceleration profiles of the internal modules, which are difficult to measure experimentally.

Study on Cylindrical Heatsink Forging Process Considering Friction Condition

2019 ◽  
Vol 823 ◽  
pp. 141-144
Author(s):  
Tung Sheng Yang ◽  
Yong Nan Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Factor ◽  
Testing Machine ◽  
Metal Flow ◽  
Compression Tests ◽  
Stress Strain ◽  
Element Analysis ◽  
Forging Process ◽  
Different Temperatures

The feasibility of forging of AL-1050 alloy of cylindrical heatsink under warm conditions is demonstrated in the present work. The stress-strain curves and friction factor play an important role in the cylindrical heatsink forging. The purpose of forging lubrication is to reduce friction between blank and die, and to decrease resistance of metal flow to die. The stress-strain curves at different temperatures are obtained by compressing tests. The friction factor between 1050 aluminum alloy and die material are determined at different temperatures by ring compression tests with graphite lubricants. The compressing and ring compressing tests are carried out by using the computerized screw universal testing machine. The finite element method is used to investigate the forming characters of the forging process. To verify the prediction of FEM simulation in the cylindrical heatsink forging process, the experimental parameters such as stress-strain curves and fiction factor, are as the input data during analysis. Maximum forging load and effective stress distribution are determined of the heatsink forging, using the finite element analysis. Finally, the cylindrical heatsink parts are formed by the forging machine under the conditions using finite element analysis.

Finite element analysis of elastomer used in automotive suspension systems

2019 ◽  
Vol 52 (6) ◽  
pp. 521-536
Author(s):  
R Karthikeyan ◽  
S Rajkumar ◽  
R Joseph Bensingh ◽  
M Abdul Kader ◽  
Sanjay K Nayak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Uniaxial Stress ◽  
Leaf Spring ◽  
Loading Conditions ◽  
Element Analysis ◽  
Rubber Material ◽  
Hyperelastic Materials ◽  
Automotive Suspension

Present research endeavours towards the development of a methodology to enhance the life of hyperelastic materials in automotive suspension (leaf spring) system. The durability of the elastomeric (rubber) material in the insert was determined at various loading conditions for better operation. Three different rubber materials were used as the models including the currently used rubber material in the suspension system. The non-linear finite element analysis was carried out for the three different materials with the uniaxial stress–strain data as the input source for the material properties. A suitable hyperelastic model was also used as the input for determining the deformation and the stress concentration in the leaf spring tip insert. The failure of the tip insert was determined in various loading conditions and the best design for limited stress concentration with higher reliability was determined in the three models. The overall results are tabulated and compared for better utilization of rubber as a tip insert in the automotive industry.

scholarly journals Investigation of the Prediction Accuracy of a Finite Element Analysis Model for the Coating Thickness in Cross-Wedge Rolled Coaxial Hybrid Parts

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 2969 ◽  
Author(s):  
Jagodzinski ◽  
Kruse ◽  
Barroi ◽  
Mildebrath ◽  
Langner ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cross Section ◽  
Coating Thickness ◽  
Wedge Angle ◽  
Research Centre ◽  
Cross Wedge Rolling ◽  
Element Analysis ◽  
Hybrid Parts ◽  
Experimental Trials

The Collaborative Research Centre 1153 (CRC 1153) “Process chain for the production of hybrid high-performance components through tailored forming” aims to develop new process chains for the production of hybrid bulk components using joined semi-finished workpieces. The subproject B1 investigates the formability of hybrid parts using cross-wedge rolling. This study investigates the reduction of the coating thickness of coaxially arranged semi-finished hybrid parts through cross-wedge rolling. The investigated parts are made of two steels (1.0460 and 1.4718) via laser cladding with hot-wire. The rolling process is designed by finite element (FE)-simulations and later experimentally investigated. Research priorities include investigations of the difference in the coating thickness of the laser cladded 1.4718 before and after cross-wedge rolling depending on the wedge angle β, cross-section reduction ∆A, and the forming speed ν. Also, the simulations and the experimental trials are compared to verify the possibility of predicting the thickness via finite element analysis (FEA). The main finding was the ability to describe the forming behavior of coaxially arranged hybrid parts at a cross-section reduction of 20% using FEA. For a cross-section reduction of 70% the results showed a larger deviation between simulation and experimental trials. The deviations were between 0.8% and 26.2%.

Sign in / Sign up

Export Citation Format

Share Document