scholarly journals The Application of a Linear Microphone Array in the Quantitative Evaluation of the Blade Trailing-Edge Noise Reduction

2021 ◽  
Vol 11 (2) ◽  
pp. 572
Author(s):  
Weijie Chen ◽  
Luqin Mao ◽  
Kangshen Xiang ◽  
Fan Tong ◽  
Weiyang Qiao
Keyword(s):  
Noise Reduction ◽  
Quantitative Evaluation ◽  
Microphone Array ◽  
Experimental Studies ◽  
Flow Speed ◽  
Aerodynamic Noise ◽  
Noise Sources ◽  
Trailing Edge ◽  
Array Data ◽  
Clean Algorithm

This paper concerns the application of a linear microphone array in the quantitative evaluation of blade trailing-edge (TE) noise reduction. The noise radiation from the blades with straight and serrated TEs is measured in an indoor open-jet wind tunnel. The array data are processed using the inverse method based on the Clean algorithm based on spatial source coherence (Clean-SC). In order to obtain correct application and achieve the best effect for the microphone array test, the computing software for array data reduction is firstly developed and assessed by Sarradj’s benchmark case. The assessment results show that the present array data processing method has a good accuracy with an error less than 0.5 dB in a wide frequency range. Then, a linear array with 32 microphones is designed to identify the noise source of a NACA65(12)-10 blade. The performance of the Clean-SC algorithm is compared with the Clean algorithm based on point spread functions (Clean-PSF) method for experimentally identifying the noise sources of the blade. The results show that there is about a 2 dB error when using the Clean-PSF algorithm due to the interference of different aerodynamic noise sources. Experimental studies are conducted to study the blade TE noise reduction using serrated TEs. The TE noise for the blade with and without sawtooth configurations is measured with the flow speeds from 20 m/s to 70 m/s, and the corresponding Reynolds numbers based on the chord are from 200,000 to 700,000. Parametric studies of the sawtooth amplitude and wavelength are conducted to understand the noise reduction law. It is observed that the TE noise reduction is sensitive to both the amplitude and wavelength. The flow speed also affects the noise reduction in the serrated TEs. To obtain the best noise suppression effect, the sawtooth configuration should be carefully designed according to the actual working conditions and airflow parameters.

scholarly journals Bio-Inspired Aerodynamic Noise Control: A Bibliographic Review

2019 ◽  
Vol 9 (11) ◽  
pp. 2224 ◽  
Author(s):  
Yong Wang ◽  
Kun Zhao ◽  
Xiang-Yu Lu ◽  
Yu-Bao Song ◽  
Gareth J. Bennett
Keyword(s):  
Noise Reduction ◽  
Noise Control ◽  
Experimental Studies ◽  
Morphological Characteristics ◽  
Leading Edge ◽  
Aerodynamic Noise ◽  
Trailing Edge ◽  
Reduction Techniques ◽  
Noise Measurements ◽  
Underlying Mechanisms

It is well-known that many species of owl have the unique ability to fly silently, which can be attributed to their distinctive and special feather adaptations. Inspired by the owls, researchers attempted to reduce the aerodynamic noise of aircraft and other structures by learning their noise reduction features from different viewpoints and then using the gained knowledge to develop a number of innovative noise reduction solutions. Although fruitful results have been achieved in the bio-inspired aerodynamic noise control, as far as the authors know, comparatively little work has been done to summarize the main findings and progresses in this area. In this bibliographic survey, we systematically review the progresses and trends of the bio-inspired aerodynamic noise control, including the macroscopic and microscopic morphological characteristics of the owl wing feathers, the noise measurements on both flying birds in the field and prepared wings in the wind tunnel, as well as theoretical, numerical and experimental studies that explored the feasibility, parameter influence, aerodynamic effects and underlying mechanisms of the four main bio-inspired noise reduction techniques, i.e., leading edge serrations, trailing edge serrations, fringe-type trailing edge extensions and porous material inspired noise reduction. Finally, we also give some suggestions for future work.

Numerical study on the airfoil self-noise of three owl-based wings with the trailing-edge serrations

2021 ◽  
pp. 095441002098822
Author(s):  
Dian Li ◽  
Xiaomin Liu ◽  
Lei Wang ◽  
Fujia Hu ◽  
Guang Xi
Keyword(s):  
Flow Field ◽  
Noise Reduction ◽  
Numerical Study ◽  
Barn Owl ◽  
Aerodynamic Noise ◽  
Frequency Noise ◽  
Trailing Edge ◽  
Reduction Mechanisms ◽  
Trailing Edge Serrations ◽  
Bionic Airfoil

Previous publications have summarized that three special morphological structures of owl wing could reduce aerodynamic noise under low Reynolds number flows effectively. However, the coupling noise-reduction mechanism of bionic airfoil with trailing-edge serrations is poorly understood. Furthermore, while the bionic airfoil extracted from natural owl wing shows remarkable noise-reduction characteristics, the shape of the owl-based airfoils reconstructed by different researchers has some differences, which leads to diversity in the potential noise-reduction mechanisms. In this article, three kinds of owl-based airfoils with trailing-edge serrations are investigated to reveal the potential noise-reduction mechanisms, and a clean airfoil based on barn owl is utilized as a reference to make a comparison. The instantaneous flow field and sound field around the three-dimensional serrated airfoils are simulated by using incompressible large eddy simulation coupled with the FW-H equation. The results of unsteady flow field show that the flow field of Owl B exhibits stronger and wider-scale turbulent velocity fluctuation than that of other airfoils, which may be the potential reason for the greater noise generation of Owl B. The scale and magnitude of alternating mean convective velocity distribution dominates the noise-reduction effect of trailing-edge serrations. The noise-reduction characteristic of Owl C outperforms that of Barn owl, which suggests that the trailing-edge serrations can suppress vortex shedding noise of flow field effectively. The trailing-edge serrations mainly suppress the low-frequency noise of the airfoil. The trailing-edge serration can suppress turbulent noise by weakening pressure fluctuation.

Trailing-edge noise reduction of a wing by a surface modification

2021 ◽  
Vol 263 (3) ◽  
pp. 3194-3201
Author(s):  
Varun Bharadwaj Ananthan ◽  
R.A.D. Akkermans ◽  
Dragan Kozulovic
Keyword(s):  
Noise Reduction ◽  
Stochastic Approach ◽  
Slight Reduction ◽  
Noise Sources ◽  
Trailing Edge ◽  
Sound Sources ◽  
Airframe Noise ◽  
Trailing Edge Noise ◽  
Random Particle ◽  
Noise Production

There is an increased emphasis on reducing airframe noise in the last decades. Airframe noise is sound generated by the interaction of a turbulent flow with the aircraft geometry, and significantly contributes to the overall noise production during the landing phase. One examples of airframe noise is the noise generated at a wing's trailing edge, i.e., trailing-edge noise. In this contribution, we numerically explore the local application of riblets for the purpose of trailing-edge noise reduction. Two configurations are studied: i) a clean NACA0012 wing section as a reference, and ii) the same configuration with riblets installed at the wing's aft part. The numerical investigation follows a hybrid computational aeroacoustics approach, where the time-average flow is studied by means of RANS. Noise sources are generated by means of a stochastic approach called Fast Random Particle Mesh method. The results show a deceleration of the flow behind the riblets. Furthermore, the turbulent kinetic energy indicates increased unsteadiness behind the riblets which is shifted away from the wall due to the presence of the riblets. Lastly, the sound sources are investigated by means of the 3D Lamb-vector, which indicates a slight reduction in magnitude near the trailing edge.

scholarly journals Research on Aerodynamic Noise Reduction for High-Speed Trains

2016 ◽  
Vol 2016 ◽  
pp. 1-21 ◽  
Author(s):  
Yadong Zhang ◽  
Jiye Zhang ◽  
Tian Li ◽  
Liang Zhang ◽  
Weihua Zhang
Keyword(s):  
Noise Reduction ◽  
High Speed ◽  
Low Noise ◽  
Broadband Noise ◽  
Full Scale ◽  
Noise Model ◽  
Aerodynamic Noise ◽  
High Speed Train ◽  
Detached Eddy Simulation ◽  
Noise Sources

A broadband noise source model based on Lighthill’s acoustic theory was used to perform numerical simulations of the aerodynamic noise sources for a high-speed train. The near-field unsteady flow around a high-speed train was analysed based on a delayed detached-eddy simulation (DDES) using the finite volume method with high-order difference schemes. The far-field aerodynamic noise from a high-speed train was predicted using a computational fluid dynamics (CFD)/Ffowcs Williams-Hawkings (FW-H) acoustic analogy. An analysis of noise reduction methods based on the main noise sources was performed. An aerodynamic noise model for a full-scale high-speed train, including three coaches with six bogies, two inter-coach spacings, two windscreen wipers, and two pantographs, was established. Several low-noise design improvements for the high-speed train were identified, based primarily on the main noise sources; these improvements included the choice of the knuckle-downstream or knuckle-upstream pantograph orientation as well as different pantograph fairing structures, pantograph fairing installation positions, pantograph lifting configurations, inter-coach spacings, and bogie skirt boards. Based on the analysis, we designed a low-noise structure for a full-scale high-speed train with an average sound pressure level (SPL) 3.2 dB(A) lower than that of the original train. Thus, the noise reduction design goal was achieved. In addition, the accuracy of the aerodynamic noise calculation method was demonstrated via experimental wind tunnel tests.

Numerical Analysis of an Industrial Fan Fitted With Noise Reduction Devices

2006 ◽  
Author(s):  
J. Amaral Teixeira ◽  
E. Naylor ◽  
P. C. Ivey ◽  
A. G. Sheard ◽  
I. R. Kinghorn
Keyword(s):  
Numerical Analysis ◽  
Noise Reduction ◽  
Flow Characteristics ◽  
Pressure Rise ◽  
Broadband Noise ◽  
Noise Sources ◽  
Fan Noise ◽  
Trailing Edge ◽  
Low Speed ◽  
The Individual

The reduction of noise emitted by industrial low speed cooling fans, particularly those fitted to air conditioning systems is a concern to fan manufacturers. The market for industrial low speed fans is highly competitive, with fan noise being the major differentiating factor between competing products. Noise reduction strategies are therefore implemented but these can adversely affect the fan’s pressure delivery capability. A reduction of fan speed can also lead to a reduction in fan noise but this is usually accompanied by a corresponding reduction in pressure rise and flow rate. The practical difficulties associated with maintaining fan pressure and flow characteristics while simultaneously reducing fan noise present fan manufacturers with a challenge. Traditional empirical approaches to the reduction of fan noise have almost been exhausted and no longer offer the potential to significantly reduce fan noise. The understanding of the aerodynamic mechanisms that act as broadband noise sources in low speed fans has been the subject of a considerable number of papers over many years. For most fans operating as a single blade row, the main sources of noise, other than those dependent on the incident turbulence levels, depend on the trailing edge and tip gap flow conditions. A range of strategies seeking to control the noise generated by these regions have been proposed over time by various authors and a number of these schemes have reached production status. The current paper details the numerical analysis of an industrial low speed fan, commonly used in conjunction with a cooling matrix, and which incorporates two distinct noise reduction features; trailing edge crenulations and a blade tip fence. Comparisons are carried out between various combinations of blades, with and without the individual features, and a discussion of the aerodynamics of the particular configurations is undertaken from a perspective of their noise reduction capabilities.

The generation of sound in turbulent motion

2008 ◽  
Vol 112 (1133) ◽  
pp. 381-394 ◽  
Author(s):  
G. M. Lilley
Keyword(s):  
Noise Reduction ◽  
Turbulent Flows ◽  
High Speed ◽  
Experimental Studies ◽  
Supersonic Jet ◽  
Jet Noise ◽  
Aerodynamic Noise ◽  
Turbulent Shear ◽  
Noise Generation ◽  
Physical Mechanisms

Abstract The present paper reviews and discusses the physical mechanisms of noise generation and reduction in turbulent flows with their applications towards aircraft noise reduction at takeoff and on the approach. This work began in 1948 when Lilley undertook an experimental investigation into the source of jet noise as a necessary precursor to finding methods for the reduction of high speed jet engine noise on civil jet airliners. Westley and Lilley completed this experimental programme in 1951, which included the design of a range of devices for high speed jet noise reduction. It was about this time that similar studies on jet noise were being started elsewhere and in particular by Lassiter and Hubbard in USA. The major contribution to the subject of turbulence as a source of noise came from Sir James Lighthill’s remarkable theory in 1952. In spite of the difficulties attached to theoretical and experimental studies on noise from turbulence, it is shown that with the accumulated knowledge on aerodynamic noise over the past 50 years, together with an optimisation of aircraft operations including flight trajectories, we are today on the threshold of approaching the design of commercial aircraft with turbofan propulsion engines that will not be heard above the background noise of the airport at takeoff and landing beyond 1-2km, from the airport boundary fence. It is evident that in the application of this work, which centres on the physical mechanisms relating to the generation of noise from turbulence and turbulent shear flows, to jet noise, there is not one unique mechanism of jet noise generation for all jet Mach numbers. This author in this publication has concentrated on what appears to be the dominant mechanism of noise generation from turbulence, where the mean convection speeds of the turbulence are subsonic. The noise generated at transonic and supersonic jet speeds invariably involves extra mechanisms, which are only briefly referred to here.

scholarly journals Self Noise Reduction and Aerodynamics of Airfoils With Porous Trailing Edges

Acoustics ◽  
2019 ◽  
Vol 1 (2) ◽  
pp. 393-409 ◽  
Author(s):  
Thomas Fritz Geyer ◽  
Ennes Sarradj
Keyword(s):  
Porous Material ◽  
Porous Materials ◽  
Microphone Array ◽  
Aerodynamic Performance ◽  
Aerodynamic Noise ◽  
Trailing Edge ◽  
Suitable Material ◽  
Trailing Edge Noise ◽  
Negative Effect ◽  
Noticeable Reduction

The application of open-porous materials is a possible method to effectively reduce the aerodynamic noise of an airfoil. However, the porous consistency may have a negative effect on the aerodynamic performance of the airfoil, since very often the lift is decreased while the drag increases. In a recent investigation, the generation of trailing edge noise of a set of airfoil models made from different porous materials was examined experimentally. The materials were characterized mainly by their airflow resistivity. Besides the material, the chordwise extent of the porous material was varied, which was done by covering the front part of the porous airfoil with a thin, impermeable adhesive foil. Acoustic measurements were performed in an open jet wind tunnel using microphone array technology, while the aerodynamic performance was measured simultaneously using a six-component balance. In general, both the airflow resistivity and the extent of the porous material have an influence on the trailing edge noise. However, if a suitable material is chosen, the results show that a noticeable reduction of trailing edge noise is possible even with only a small chordwise extent of the porous material.

scholarly journals Noise reduction mechanisms of sawtooth and combed-sawtooth trailing-edge serrations

2018 ◽  
Vol 848 ◽  
pp. 560-591 ◽  
Author(s):  
F. Avallone ◽  
W. C. P. van der Velden ◽  
D. Ragni ◽  
D. Casalino
Keyword(s):  
Noise Reduction ◽  
Correlation Length ◽  
Surface Pressure ◽  
Pressure Fluctuations ◽  
Empty Space ◽  
Frequency Range ◽  
Noise Sources ◽  
Trailing Edge ◽  
Trailing Edge Serrations ◽  
The One

Trailing-edge serrations are add ons retrofitted to wind-turbine blades to mitigate turbulent boundary-layer trailing-edge noise. This manuscript studies the physical mechanisms behind the noise reduction by investigating the far-field noise and the hydrodynamic flow field. A conventional sawtooth and a combed-sawtooth trailing-edge serration are studied. Combed-sawtooth serrations are obtained by filling the empty space between the teeth with combs (i.e. solid filaments). Both serration geometries are retrofitted to a NACA 0018 aerofoil at zero degree angle of attack. Computations are carried out by solving the explicit, transient, compressible lattice Boltzmann equation, while the acoustic far field is obtained by means of the Ffowcs Williams and Hawkings analogy. The numerical results are validated against experiments. It is confirmed that the combed-sawtooth serrations reduce noise more than the conventional sawtooth ones for the low- and mid-frequency range. It is found that the presence of combs affects the intensity of the scattered noise but not the frequency range of noise reduction. For both configurations, the intensity of the surface pressure fluctuations decreases from the root to the tip, and noise sources are mainly located at the serrations root for the low- and mid-frequency range. The presence of the filaments generates a more uniform distribution of the noise sources along the edges with respect to the conventional serration. The installation of combs mitigates the interaction between the two sides of the aerofoil at the trailing edge and the generation of a turbulent wake in the empty space between teeth. As a result, the inward (i.e. from the serration edge to the centreline) and outward (i.e. from the serration centreline to the edge) flow motions, due to the presence of the teeth, are mitigated. It is found that the installation of serrations affects the surface pressure fluctuations integral parameters. Both the spanwise correlation length and convective velocity of the surface pressure fluctuations increase with respect to the baseline straight configuration. When both quantities are similar to the one obtained for the straight trailing edge, the effect of the slanted edge is negligible, thus corresponding to no noise reduction. It is concluded that the changes in sound radiation are mainly caused by destructive interference of the radiated sound waves for which a larger spanwise correlation length is beneficial. Finally, the difference between measurements and the literature is caused by an incorrect modelling of the spanwise correlation length, which shows a different decay rate with respect to the one obtained for a straight trailing edge.

Research on Effect of Noise Emission from Railway Viaduct on Noise Reduction of Noise Barriers

2012 ◽  
Vol 433-440 ◽  
pp. 1852-1856
Author(s):  
Lei Ming Song ◽  
Shou Guang Sun ◽  
Xin Hua Zhang
Keyword(s):  
Noise Reduction ◽  
Microphone Array ◽  
Field Testing ◽  
Vibration Testing ◽  
Noise Emission ◽  
Noise Sources ◽  
Noise Barriers ◽  
Sources Identification ◽  
Array Technology ◽  
Noise Barrier

Noise sources identification based on microphone array theory was firstly introduced, A method was derived, which can be used to analyze effect of noise emission from railway viaduct to noise reduction of noise barriers. Vibration and noise emission of railway viaduct and noise barrier were studied using field testing with microphone array technology and vibration testing. The results concluded that noise emission from the viaduct has remarkable effects on noise reduction of noise barriers compared with the effects of noise emission from the noise barriers themselves, which is neglectable.

Sign in / Sign up

Export Citation Format

Share Document