scholarly journals Effect of Cylinder-by-Cylinder Variation on Performance and Gaseous Emissions of a PFI Spark Ignition Engine: Experimental and 1D Numerical Study

2021 ◽  
Vol 11 (13) ◽  
pp. 6035
Author(s):  
Luigi Teodosio ◽  
Luca Marchitto ◽  
Cinzia Tornatore ◽  
Fabio Bozza ◽  
Gerardo Valentino
Keyword(s):  
Internal Combustion Engines ◽  
Numerical Study ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Pollutant Emissions ◽  
Gaseous Emissions ◽  
Performance And Emissions ◽  
The Impact

Combustion stability, engine efficiency and emissions in a multi-cylinder spark-ignition internal combustion engines can be improved through the advanced control and optimization of individual cylinder operation. In this work, experimental and numerical analyses were carried out on a twin-cylinder turbocharged port fuel injection (PFI) spark-ignition engine to evaluate the influence of cylinder-by-cylinder variation on performance and pollutant emissions. In a first stage, experimental tests are performed on the engine at different speed/load points and exhaust gas recirculation (EGR) rates, covering operating conditions typical of Worldwide harmonized Light-duty vehicles Test Cycle (WLTC). Measurements highlighted relevant differences in combustion evolution between cylinders, mainly due to non-uniform effective in-cylinder air/fuel ratio. Experimental data are utilized to validate a one-dimensional (1D) engine model, enhanced with user-defined sub-models of turbulence, combustion, heat transfer and noxious emissions. The model shows a satisfactory accuracy in reproducing the combustion evolution in each cylinder and the temperature of exhaust gases at turbine inlet. The pollutant species (HC, CO and NOx) predicted by the model show a good agreement with the ones measured at engine exhaust. Furthermore, the impact of cylinder-by-cylinder variation on gaseous emissions is also satisfactorily reproduced. The novel contribution of present work mainly consists in the extended numerical/experimental analysis on the effects of cylinder-by-cylinder variation on performance and emissions of spark-ignition engines. The proposed numerical methodology represents a valuable tool to support the engine design and calibration, with the aim to improve both performance and emissions.

scholarly journals Ammonia Emissions in SI Engines Fueled with LPG

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 691
Author(s):  
Andrzej Żółtowski ◽  
Wojciech Gis
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Mixture ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Catalytic Reactor ◽  
Si Engines ◽  
Engine Testing ◽  
The Impact

Ammonia is a toxic exhaust component emitted from internal combustion engines. Both pure ammonia and the products of its reaction with nitrogen and sulfur compounds, being the source of particulate matter (PM) emissions, are dangerous for human health and life. The aim of the article was to demonstrate that NH3 can be produced in exhaust gas after-treatment systems of spark-ignition (SI) engines used in light-duty vehicles. In some cases, NH3 occurs in high enough concentrations that can be harmful and dangerous. It would be reasonable to collect research data regarding this problem and consider the advisability of limiting these pollutant emissions in future regulations. The article presents the results of the spark-ignition engine testing on an engine test bench and discusses the impact of the air–fuel ratio regulation and some engine operating parameters on the concentration of NH3. It has been proven that in certain engine operating conditions and a combination of circumstances like the three-way catalytic reactor (TWC) temperature and periodic enrichment of the air–fuel mixture may lead to excessive NH3 emissions resulting from the NO conversion in the catalytic reactor. This is a clear disadvantage due to the lack of limitation of these pollutant emissions by the relevant type-approval regulations. This article should be a contribution to discussion among emissions researchers whether future emission regulations (e.g., Euro 7 or Euro VII) should include a provision to reduce NH3 emissions from all vehicles.

scholarly journals 1D numerical study on hydrogen injection enabling ultra-lean combustion in a small gasoline Spark Ignition engine

2020 ◽  
Vol 197 ◽  
pp. 06001
Author(s):  
Luigi Teodosio ◽  
Dino Pirrello ◽  
Luca Marchitto
Keyword(s):  
High Efficiency ◽  
Laminar Flame ◽  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Numerical Code ◽  
Hydrogen Addition ◽  
1D Model ◽  
The Impact

This paper deals with the effects of hydrogen port injection on combustion evolution, efficiency and exhaust emissions of a small turbocharged gasoline Spark-Ignition engine through a 1D numerical code. First, the experiments on the base engine architecture are performed at different speeds and at low/medium loads. The experimental findings are used to validate a 1D model of the whole engine, developed within a commercial code. 1D model is also refined with “user-defined” sub-models for an accurate description of the in-cylinder phenomena, namely turbulence, combustion, heat transfer, and emissions. In a second step, 1D model is virtually modified through the installation of an hydrogen injector in each intake runner, while the combustion sub-model also accounts for the impact of hydrogen addition on the laminar flame speed through a dedicated correlation. 1D simulations are performed at low/medium loads and fixed speed of 2250 rpm with 5% of hydrogen by volume in the intake air. Numerical investigations show that hydrogen addition to gasoline/air mixtures allows relevant efficiency benefits (up to a maximum percent gain of 19%), while the NO emissions are almost eliminated. Consequently, hydrogen-boosted combustion represents a potential solution to achieve very high efficiency and reduced pollutant emissions of gasoline spark ignition engines equipped with a conventional combustion system.

scholarly journals Ethanol/Gasoline Blends as Alternative Fuel in Last Generation Spark-Ignition Engines: A Review on CO and HC Engine Out Emissions

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 4034
Author(s):  
Paolo Iodice ◽  
Massimo Cardone
Keyword(s):  
Physicochemical Properties ◽  
Alternative Fuels ◽  
Experimental Studies ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
The Impact

Among the alternative fuels existing for spark-ignition engines, ethanol is considered worldwide as an important renewable fuel when mixed with pure gasoline because of its favorable physicochemical properties. An in-depth and updated investigation on the issue of CO and HC engine out emissions related to use of ethanol/gasoline fuels in spark-ignition engines is therefore necessary. Starting from our experimental studies on engine out emissions of a last generation spark-ignition engine fueled with ethanol/gasoline fuels, the aim of this new investigation is to offer a complete literature review on the present state of ethanol combustion in last generation spark-ignition engines under real working conditions to clarify the possible change in CO and HC emissions. In the first section of this paper, a comparison between physicochemical properties of ethanol and gasoline is examined to assess the practicability of using ethanol as an alternative fuel for spark-ignition engines and to investigate the effect on engine out emissions and combustion efficiency. In the next section, this article focuses on the impact of ethanol/gasoline fuels on CO and HC formation. Many studies related to combustion characteristics and exhaust emissions in spark-ignition engines fueled with ethanol/gasoline fuels are thus discussed in detail. Most of these experimental investigations conclude that the addition of ethanol with gasoline fuel mixtures can really decrease the CO and HC exhaust emissions of last generation spark-ignition engines in several operating conditions.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

scholarly journals LES study on mixing and combustion in a Direct Injection Spark Ignition engine

2018 ◽  
Vol 73 ◽  
pp. 32
Author(s):  
Nicolas Iafrate ◽  
Anthony Robert ◽  
Jean-Baptiste Michel ◽  
Olivier Colin ◽  
Benedicte Cuenot ◽  
...  
Keyword(s):  
Ignition Time ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Spark Ignition Engines ◽  
Eddy Simulation ◽  
Mixture Preparation ◽  
The Impact

Downsized spark ignition engines coupled with a direct injection strategy are more and more attractive for car manufacturers in order to reduce pollutant emissions and increase efficiency. However, the combustion process may be affected by local heterogeneities caused by the interaction between the spray and turbulence. The aim for car manufacturers of such engine strategy is to create, for mid-to-high speeds and mid-up-high loads, a mixture which is as homogeneous as possible. However, although injection occurs during the intake phase, which favors homogeneous mixing, local heterogeneities of the equivalence ratio are still observed at the ignition time. The analysis of the mixture preparation is difficult to perform experimentally because of limited optical accesses. In this context, numerical simulation, and in particular Large Eddy Simulation (LES) are complementary tools for the understanding and analysis of unsteady phenomena. The paper presents the LES study of the impact of direct injection on the mixture preparation and combustion in a spark ignition engine. Numerical simulations are validated by comparing LES results with experimental data previously obtained at IFPEN. Two main analyses are performed. The first one focuses on the fuel mixing and the second one concerns the effect of the liquid phase on the combustion process. To highlight these phenomena, simulations with and without liquid injection are performed and compared.

The Potential of a Separated Electric Compound Spark Ignition Engine for Hybrid Vehicle Application

2022 ◽  
Author(s):  
Emiliano Pipitone ◽  
Salvatore Caltabellotta
Keyword(s):  
Internal Combustion Engines ◽  
Ambient Pressure ◽  
Spark Ignition ◽  
Hybrid Vehicle ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Exhaust Gas ◽  
Engine Fuel ◽  
Generator Unit ◽  
Overall Efficiency

Abstract In-cylinder expansion of internal combustion engines based on Diesel or Otto cycles cannot be completely brought down to ambient pressure, causing a 20% theoretical energy loss. Several systems have been implemented to recover and use this energy such as turbocharging, turbo-mechanical and turbo-electrical compounding, or the implementation of Miller Cycles. In all these cases however, the amount of energy recovered is limited allowing the engine to reach an overall efficiency incremental improvement between 4% and 9%. Implementing an adequately designed expander-generator unit could efficiently recover the unexpanded exhaust gas energy and improve efficiency. In this work, the application of the expander-generator unit to a hybrid propulsion vehicle is considered, where the onboard energy storage receives power produced by an expander-generator, which could hence be employed for vehicle propulsion through an electric drivetrain. Starting from these considerations, a simple but effective modelling approach is used to evaluate the energetic potential of a spark-ignition engine electrically supercharged and equipped with an exhaust gas expander connected to an electric generator. The overall efficiency was compared to a reference turbocharged engine within a hybrid vehicle architecture. It was found that, if adequately recovered, the unexpanded gas energy could reduce engine fuel consumption and related pollutant emissions by 4% to 12%, depending on overall power output.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

2021 ◽  
pp. 146808742110346
Author(s):  
Sanguk Lee ◽  
Gyeonggon Kim ◽  
Choongsik Bae
Keyword(s):  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Transport Sector ◽  
Injection Timing ◽  
Ignition Timing ◽  
Particulate Emission ◽  
Stratified Charge ◽  
Lean Limit

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

Experimental and numerical study on the influence of cooled EGR on knock tendency, performance and emissions of a downsized spark-ignition engine

Energy ◽  
2019 ◽  
Vol 172 ◽  
pp. 968-976 ◽  
Author(s):  
Cinzia Tornatore ◽  
Fabio Bozza ◽  
Vincenzo De Bellis ◽  
Luigi Teodosio ◽  
Gerardo Valentino ◽  
...  
Keyword(s):  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Performance And Emissions

Development of the Control and Acquisition System for a Natural-Gas Spark-Ignition Engine Test Bench

2019 ◽  
Author(s):  
Lorenzo Gasbarro ◽  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu ◽  
Luca Ambrogi ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Acquisition System ◽  
Combustion Engines ◽  
Engine Test ◽  
New Sensors

Abstract Investigations using laboratory test benches are the most common way to find the technological solutions that will increase the efficiency of internal combustion engines and curtail their emissions. In addition, the collected experimental data are used by the CFD community to develop engine models that reduce the time-to-market. This paper describes the steps made to increase the reliability of engine experiments performed in a heavy-duty natural-gas spark-ignition engine test-cell such as the design of the control and data acquisition system based on Modbus TCP communication protocol. Specifically, new sensors and a new dynamometer controller were installed. The operation of the improved test bench was investigated at several operating conditions, with data obtained at both high- and low-sampling rates. The results indicated a stable test bench operation.

A comparative study of the effect of compression ratio on the efficiency and flame development angle in a Cooperative Fuel Research engine fueled with binary gasoline–alcohol blends

2019 ◽  
pp. 146808741985910 ◽  
Author(s):  
Guillermo Rubio-Gómez ◽  
Lis Corral-Gómez ◽  
David Rodriguez-Rosa ◽  
Fausto A Sánchez-Cruz ◽  
Simón Martínez-Martínez
Keyword(s):  
Comparative Study ◽  
Compression Ratio ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Flame Development ◽  
The Impact

In the last few years, increasing concern about the harmful effects of the use of fossil fuels in internal combustion engines has been observed. In addition, the limited availability of crude oil has driven the interest in alternative fuels, especially biofuels. In the context of spark ignition engines, bioalcohols are of great interest owing to their similarities and blend capacities with gasoline. Methanol and ethanol have been widely used, mainly due to their knocking resistance. Another alcohol of great interest is butanol, thanks to its potential of being produced as biofuel and its heat value closer to gasoline. In this study, a comparative study of gasoline–alcohol blend combustion, with up to 20% volume, with neat gasoline has been carried out. A single-cylinder, variable compression ratio, Cooperative Fuel Research-type spark ignition engine has been employed. The comparison is made in terms of fuel conversion efficiency and flame development angle. Relevant information related to the impact in the combustion process of the use of the three main alcohols used in blends with gasoline has been obtained.

Sign in / Sign up

Export Citation Format

Share Document