scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

scholarly journals Impact of Pyrolysis Oil Addition to Ethanol on Combustion in the Internal Combustion Spark Ignition Engine

2021 ◽  
Vol 3 (2) ◽  
pp. 450-461
Author(s):  
Magdalena Szwaja ◽  
Mariusz Chwist ◽  
Stanislaw Szwaja ◽  
Romualdas Juknelevičius
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Calorific Value ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Spark Ignition Engines ◽  
Pyrolysis Oil ◽  
Indicated Mean Effective Pressure ◽  
Spark Timing

Thermal processing (torrefaction, pyrolysis, and gasification), as a technology can provide environmentally friendly use of plastic waste. However, it faces a problem with respect to its by-products. Pyrolysis oil obtained using this technology is seen as a substance that is extremely harmful for living creatures and that needs to be neutralized. Due to its relatively high calorific value, it can be considered as a potential fuel for internal combustion spark-ignition engines. In order make the combustion process effective, pyrolysis oil is blended with ethanol, which is commonly used as a fuel for flexible fuel cars. This article presents results from combustion tests conducted on a single-cylinder research engine at full load working at 600 rpm at a compression ratio of 9.5:1, and an equivalence ratio of 1. The analysis showed improvements in combustion and engine performance. It was found that, due to the higher calorific value of the blend, the engine possessed a higher indicated mean effective pressure. It was also found that optimal spark timing for this ethanol-pyrolysis oil blend was improved at a crank angle of 2–3° at 600 rpm. In summary, ethanol-pyrolysis oil blends at a volumetric ratio of 3:1 (25% pyrolysis oil) can successfully substitute ethanol in spark-ignition engines, particularly for vehicles with flexible fuel type.

scholarly journals LES study on mixing and combustion in a Direct Injection Spark Ignition engine

2018 ◽  
Vol 73 ◽  
pp. 32
Author(s):  
Nicolas Iafrate ◽  
Anthony Robert ◽  
Jean-Baptiste Michel ◽  
Olivier Colin ◽  
Benedicte Cuenot ◽  
...  
Keyword(s):  
Ignition Time ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Pollutant Emissions ◽  
Spark Ignition Engines ◽  
Eddy Simulation ◽  
Mixture Preparation ◽  
The Impact

Downsized spark ignition engines coupled with a direct injection strategy are more and more attractive for car manufacturers in order to reduce pollutant emissions and increase efficiency. However, the combustion process may be affected by local heterogeneities caused by the interaction between the spray and turbulence. The aim for car manufacturers of such engine strategy is to create, for mid-to-high speeds and mid-up-high loads, a mixture which is as homogeneous as possible. However, although injection occurs during the intake phase, which favors homogeneous mixing, local heterogeneities of the equivalence ratio are still observed at the ignition time. The analysis of the mixture preparation is difficult to perform experimentally because of limited optical accesses. In this context, numerical simulation, and in particular Large Eddy Simulation (LES) are complementary tools for the understanding and analysis of unsteady phenomena. The paper presents the LES study of the impact of direct injection on the mixture preparation and combustion in a spark ignition engine. Numerical simulations are validated by comparing LES results with experimental data previously obtained at IFPEN. Two main analyses are performed. The first one focuses on the fuel mixing and the second one concerns the effect of the liquid phase on the combustion process. To highlight these phenomena, simulations with and without liquid injection are performed and compared.

scholarly journals Parametric Knocking Performance Investigation of Spark Ignition Natural Gas Engines and Dual Fuel Engines

2020 ◽  
Vol 8 (6) ◽  
pp. 459 ◽  
Author(s):  
La Xiang ◽  
Gerasimos Theotokatos ◽  
Haining Cui ◽  
Keda Xu ◽  
Hongkai Ben ◽  
...  
Keyword(s):  
Natural Gas ◽  
Compression Ratio ◽  
Engine Performance ◽  
Spark Ignition ◽  
Combustion Model ◽  
Dual Fuel ◽  
Ignition Timing ◽  
Natural Gas Engines ◽  
Study Results ◽  
Pilot Fuel

Both spark ignition (SI) natural gas engines and compression ignition (CI) dual fuel (DF) engines suffer from knocking when the unburnt mixture ignites spontaneously prior to the flame front arrival. In this study, a parametric investigation is performed on the knocking performance of these two engine types by using the GT-Power software. An SI natural gas engine and a DF engine are modelled by employing a two-zone zero-dimensional combustion model, which uses Wiebe function to determine the combustion rate and provides adequate prediction of the unburnt zone temperature, which is crucial for the knocking prediction. The developed models are validated against experimentally measured parameters and are subsequently used for performing parametric investigations. The derived results are analysed to quantify the effect of the compression ratio, air-fuel equivalence ratio and ignition timing on both engines as well as the effect of pilot fuel energy proportion on the DF engine. The results demonstrate that the compression ratio of the investigated SI and DF engines must be limited to 11 and 16.5, respectively, for avoiding knocking occurrence. The ignition timing for the SI and the DF engines must be controlled after −38°CA and 3°CA, respectively. A higher pilot fuel energy proportion between 5% and 15% results in increasing the knocking tendency and intensity for the DF Engine at high loads. This study results in better insights on the impacts of the investigated engine design and operating settings for natural gas (NG)-fuelled engines, thus it can provide useful support for obtaining the optimal settings targeting a desired combustion behaviour and engine performance while attenuating the knocking tendency.

Experimental and numerical study on the influence of cooled EGR on knock tendency, performance and emissions of a downsized spark-ignition engine

Energy ◽  
2019 ◽  
Vol 172 ◽  
pp. 968-976 ◽  
Author(s):  
Cinzia Tornatore ◽  
Fabio Bozza ◽  
Vincenzo De Bellis ◽  
Luigi Teodosio ◽  
Gerardo Valentino ◽  
...  
Keyword(s):  
Numerical Study ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Performance And Emissions

scholarly journals Simulation of spark ignition engine performance working on biogas hydrogen mixture

2018 ◽  
Vol 244 ◽  
pp. 03001
Author(s):  
Donatas Kriaučiūnas ◽  
Saugirdas Pukalskas ◽  
Alfredas Rimkus
Keyword(s):  
Carbon Dioxide ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Simulation Results ◽  
Crankshaft Rotation ◽  
Carbon Dioxide Co2 ◽  
Engine Crankshaft ◽  
Lower Heating

Numerical simulations of Nissan Qashqai HR16DE engine with increased compression ratio from 10,7:1 to 13,5:1 was carried out using AVL BOOST software. Modelled engine work cycles while engine works with biogas (BG) and hydrogen (H2) mixtures. For biogas used mixture of 35 % carbon dioxide (CO2) and 65 % methane (CH4). Three mixtures of biogas with added 5 %, 10 % and 15 % H2 was made. The simulation of engine work cycles was performed at fully opened throttle and changing engine crankshaft rotation speeds: ne1 = 1500, ne2 = 3000, ne3 = 4500, ne4 = 6000 rpm. Simulation results demonstrated what adding hydrogen to biogas increase in-cylinder temperature and nitrogen oxides (NOx) concentration because of higher mixtures lower heating values (LHV) and better combustion process. Other emissions of carbon monoxide (CO) and hydrocarbons (HC) decreased while adding hydrogen due to the fact that hydrogen is carbon-free fuel.

scholarly journals The Effects of Port Water Injection on Spark Ignition Engine Performance and Emissions Fueled by Pure Gasoline, E5 and E10

Processes ◽  
2020 ◽  
Vol 8 (10) ◽  
pp. 1214
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Maria Dolores Redel-Macias ◽  
Ali Ghodsi ◽  
Seyed Vahid Hosseini ◽  
...  
Keyword(s):  
Water Injection ◽  
Engine Performance ◽  
Spark Ignition ◽  
Injection Rate ◽  
Spark Ignition Engine ◽  
Oxides Of Nitrogen ◽  
Human Beings ◽  
Performance And Emissions ◽  
Engine Performance And Emissions ◽  
Engine Power

It has been proven that vehicle emissions such as oxides of nitrogen (NOx) are negatively affecting the health of human beings as well as the environment. In addition, it was recently highlighted that air pollution may result in people being more vulnerable to the deadly COVID-19 virus. The use of biofuels such as E5 and E10 as alternatives of gasoline fuel have been recommended by different researchers. In this paper, the impacts of port injection of water to a spark ignition engine fueled by gasoline, E5 and E10 on its performance and NOx production have been investigated. The experimental work was undertaken using a KIA Cerato engine and the results were used to validate an AVL BOOST model. To develop the numerical analysis, design of experiment (DOE) method was employed. The results showed that by increasing the ethanol fraction in gasoline/ethanol blend, the brake specific fuel consumption (BSFC) improved between 2.3% and 4.5%. However, the level of NOx increased between 22% to 48%. With port injection of water up to 8%, there was up to 1% increase in engine power whereas NOx and BSFC were reduced by 8% and 1%, respectively. The impacts of simultaneous changing of the start of combustion (SOC) and water injection rate on engine power and NOx production was also investigated. It was found that the NOx concentration is very sensitive to SOC variation.

Performance and Emission Predictions for a Multi-Cylinder Spark Ignition Engine

1977 ◽  
Vol 191 (1) ◽  
pp. 339-354 ◽  
Author(s):  
R. S. Benson ◽  
P. C. Baruah
Keyword(s):  
Wave Equations ◽  
Spark Ignition ◽  
Reaction Scheme ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Performance And Emission ◽  
Nitric Oxide Formation ◽  
Performance And Emissions ◽  
The Common ◽  
Good Agreement

A comparison is made of experimental results and predictions of performance and emissions from a multi-cylinder spark ignition engine over a range of air-fuel ratios and two throttle settings. The results showed that a simplified two zone combustion model, a seven reaction scheme for nitric oxide formation, a partial freezing model for carbon monoxide and the inclusion of chemical reactions and variable specific heat along the pathlines in the wave equations gave good agreement with the measurements at the common pipe junction and exhaust outlet, but due to cyclic dispersion and maldistribution of fuel between cylinders the predictions of the emissions in the exhaust manifold adjacent to the cylinder were not so good. The predicted air flow and indicated power agreed well with experiment.

scholarly journals A Numerical Study of a Simple Stochastic/ Deterministic Model of Cycle-to-Cycle Combustion Fluctuations in Spark Ignition Engines

2005 ◽  
Vol 11 (3) ◽  
pp. 371-379 ◽  
Author(s):  
G. Litak ◽  
M. Wendeker ◽  
M. Krupa ◽  
J. Czarnigowski
Keyword(s):  
Deterministic Model ◽  
Numerical Study ◽  
Fluid Model ◽  
Combustion Process ◽  
Fuel Mixture ◽  
Spark Ignition ◽  
Spark Ignition Engines ◽  
Fuel Feed ◽  
Lean Combustion ◽  
Two Fluid Model

We examine a simple, fuel-air model of combustion in a spark ignition (SI) engine with indirect injection. In our two-fluid model, variations of fuel mass burned in cycle sequences appear due to stochastic fluctuations of a fuel feed amount. We have shown that a small amplitude of these fluctuations affects considerably the stability of a combustion process strongly depending on the quality of the air-fuel mixture. The largest influence was found in the limit of a lean combustion. The possible effect of nonlinearities in the combustion process has been also discussed.

Performance and Emissions Characteristics of Diesel Engine Fuelled by Biodiesel Derived from Palm Oil

2013 ◽  
Vol 315 ◽  
pp. 517-522 ◽  
Author(s):  
Amir Khalid ◽  
Shahrul Azmir Osman ◽  
M. Norrizam Mohamad Jaat ◽  
Norrizal Mustaffa ◽  
Siti Mariam Basharie ◽  
...  
Keyword(s):  
Palm Oil ◽  
Engine Speed ◽  
Oxidation Stability ◽  
Combustion Process ◽  
Engine Performance ◽  
Load Test ◽  
Emission Regulations ◽  
Oxygenated Fuel ◽  
Performance And Emissions ◽  
Hc Emissions

Bio fuels based on vegetable oils offer the advantage being a sustainable, annually renewable source of automobile fuel. Despite years of improvement attempts, the key issue in using vegetable oil-based fuels is oxidation stability, stoichiometric point, bio-fuel composition, antioxidants on the degradation and much oxygen with comparing to diesel gas oil. Thus, the improvement of emissions exhausted from diesel engines fueled by biodiesel derived from palm oil is urgently required to meet the future stringent emission regulations. Purpose of this study is to explore how significant the effects of palm oil blending ratio on combustion process that strongly affects the vehicles performance and exhaust emissions. The engine speed was varied from 15003000 rpm, load test condition varied by Dynapack chassis dynamometer from 050% and palm oil blending ratio from 515vol% (B5B15). Increased blends of biodiesel ratio is found to enhance the combustion process, resulting in decreased the HC emissions with nearly equal of engine performance. The improvement of combustion process is expected to be strongly influenced by oxygenated fuel in biodiesel content.

Sign in / Sign up

Export Citation Format

Share Document