scholarly journals Evaluating the Role of Aggregate Gradation on Cracking Performance of Asphalt Concrete for Thin Overlays

2019 ◽  
Vol 9 (4) ◽  
pp. 628 ◽  
Author(s):  
Lívia Garcia-Gil ◽  
Rodrigo Miró ◽  
Félix Pérez-Jiménez
Keyword(s):  
Asphalt Concrete ◽  
Material Selection ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Fine Fraction ◽  
Aggregate Size ◽  
Aggregate Gradation ◽  
Concrete Mixtures ◽  
Cracking Performance

Thin asphalt concrete overlays are a maintenance technique that mainly restore the functional properties of pavements. One of the main issues in thin overlays is reflective cracking that can cause early deterioration and reduce their service life. For this reason, the purpose of this investigation is to evaluate the effect of material selection on cracking performance of asphalt concrete mixtures for thin overlays. In particular, this paper evaluates the role of aggregate skeleton gradation. The study of the effect of aggregate gradation was divided into two stages: (1) fine fraction content and (2) maximum nominal aggregate size. Based on this, up to seven asphalt mixture gradations were designed and evaluated through the Fénix test at different test temperatures. The results showed a significant correlation between the fine fraction content, and maximum nominal aggregate size, and the cracking performance of the asphalt concrete mixtures. Mixtures manufactured with a low content of fine aggregates, as well as small nominal maximum size, experienced a further improvement of their toughness. These results reflected the importance of considering not only the effect of asphalt binder and environmental conditions but also aggregate gradation in the design of asphalt concrete mixtures in order to achieve a desirable cracking performance.

scholarly journals Assessing the Moisture and Aging Susceptibility of Cold Mix Asphalt Concrete

2021 ◽  
Vol 27 (2) ◽  
pp. 59-72
Author(s):  
Zahraa Ahmed Samor ◽  
Saad Issa Sarsam
Keyword(s):  
Tensile Strength ◽  
Portland Cement ◽  
Asphalt Concrete ◽  
Ordinary Portland Cement ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Hydrated Lime ◽  
Technical Requirements ◽  
Concrete Mixtures ◽  
Age Related

Laboratory experience in Iraq with cold asphalt concrete mixtures is very limited. The design and use of cold mixed asphalt concrete had no technical requirements. In this study, two asphalt concrete mixtures used for the base course were prepared in the laboratory using conventional cold-mixing techniques to test cold asphalt mixture (CAM) against aging and moisture susceptibility. Cold asphalt mixtures specimens have been prepared in the lab with cutback and emulsion binders, different fillers, and curing times. Based on the Marshal test result, the cutback proportion was selected with the filler, also based on the Marshal test emulsion. The first mixture was medium setting cationic emulsion (MSCE) as a binder, hydrated lime, and ordinary portland cement as a filler (7.95% MSCE + 2%HL + 3% OPC). The second mixture used was medium curing cutback (MC-250) as a binder and ordinary portland cement as a filler (5.18% MC 250 + 5% OPC). The indirect tensile strength (ITS) of the samples was measured at 25 ° C. It was found that the cold mix with the MSCE binder had a high ITS value relative to the cold mix with the cutback asphalt binder (MC-250). The dry mixture of MSCE  ITS was approximately 3.77 times the dry mixture of MC-250. The MSCE wet mix was about 4.2 times the wet MC-250 mix. Tensile strength ratio result (TSR %) for the MSCE binder mix and the cutback MC-250 binder mix showed that the MSCE mix has a reasonable moisture resistance (77% ) compared to the MC-250 mix (69.2 %). The aging test and aging ratio result showed that asphalt binder oxidation has a significant effect on age-related pavement degradation as it changes the time-temperature relationship depending on the viscoelastic properties of the asphalt binder. The result clearly showed that the MSCE binder mix had a high resistance to aging (440 Kpa) compared to the cutback (MC-250) binder mix (110 Kpa). In contrast, the MSCE aging ratio (90 %) was higher than the MC-250 ratio (85 %).

Effect of Segregation on Fatigue Performance of Asphalt Paving Mixtures

1996 ◽  
Vol 1543 (1) ◽  
pp. 63-70 ◽  
Author(s):  
Taisir S. Khedaywi ◽  
Thomas D. White
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Fatigue Performance ◽  
Fatigue Properties ◽  
Maximum Aggregate Size ◽  
Initial Stiffness ◽  
Natural Sand ◽  
Concrete Mixtures ◽  
Asphalt Paving

The main objective of this research was to investigate the effect of segregation on fatigue performance of asphalt paving mixtures. Segregation in asphalt concrete pavements occurs when coarse material is concentrated in some areas of the pavement and fine materials in others. Segregation has been one problem that has resulted in poor performance in many pavements. Materials used in the study included gravel, natural sand, and an AC-20 asphalt cement. Aggregates were selected to meet the Indiana Department of Transportation specification for a No. 8 binder with a maximum aggregate size of 1 in. (25 mm). To simulate various levels of coarse and fine segregation, four artificially segregated mixtures were prepared in addition to the control asphalt mixture. Slabs were compacted for the five mixtures using the Purdue linear compactor. These slabs were cut into beams that were used to test for the fatigue properties of the five segregated asphalt concrete mixtures. Limits of fatigue were examined when flexural stiffness was one-third and one-half of the initial stiffness at 200 load applications. Results of the investigation indicated that the fatigue life of segregated asphalt concrete mixtures was significantly affected.

scholarly journals Asphalt Mixture for the First Asphalt Concrete Directly Fastened Track in Korea

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Seong-Hyeok Lee ◽  
Dae-Wook Park ◽  
Hai Viet Vo ◽  
Samer Dessouky
Keyword(s):  
Asphalt Concrete ◽  
Design Method ◽  
Asphalt Mixture ◽  
Digital Camera ◽  
Aggregate Size ◽  
Fatigue Tests ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Aggregate Gradation ◽  
Modified Asphalt

The research has been initiated to develop the asphalt mixtures which are suitable for the surface of asphalt concrete directly fastened track (ADFT) system and evaluate the performance of the asphalt mixture. Three aggregate gradations which are upper (finer), medium, and below (coarser). The nominal maximum aggregate size of asphalt mixture was 10 mm. Asphalt mixture design was conducted at 3 percent air voids using Marshall mix design method. To make impermeable asphalt mixture surface, the laboratory permeability test was conducted for asphalt mixtures of three different aggregate gradations using asphalt mixture permeability tester. Moisture susceptibility test was conducted based on AASHTO T 283. The stripping percentage of asphalt mixtures was measured using a digital camera and analyzed based on image analysis techniques. Based on the limited research results, the finer aggregate gradation is the most suitable for asphalt mixture for ADFT system with the high TSR value and the low stripping percentage and permeable coefficient. Flow number and beam fatigue tests for finer aggregate asphalt mixture were conducted to characterize the performance of asphalt mixtures containing two modified asphalt binders: STE-10 which is styrene-butadiene-styrene (SBS) polymer and ARMA which is Crum rubber modified asphalt. The performance tests indicate that the STE-10 shows the higher rutting life and fatigue life.

A Hybrid Model to Predict the Gyratory Compaction of Hot Mixed Asphalt

2019 ◽  
Author(s):  
Teng Man
Keyword(s):  
Hybrid Model ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Compaction Process ◽  
Particle Rearrangement ◽  
Compaction Behavior ◽  
Grain Size Distributions ◽  
Gyratory Compaction

The compaction of asphalt mixture is crucial to the mechanical properties and the maintenance of the pavement. However, the mix design, which based on the compaction properties, remains largely on empirical data. We found difficulties to relate the aggregate size distribution and the asphalt binder properties to the compaction behavior in both the field and laboratory compaction of asphalt mixtures. In this paper, we would like to propose a simple hybrid model to predict the compaction of asphalt mixtures. In this model, we divided the compaction process into two mechanisms: (i) visco-plastic deformation of an ordered thickly-coated granular assembly, and (ii) the transition from an ordered system to a disordered system due to particle rearrangement. This model could take into account both the viscous properties of the asphalt binder and grain size distributions of the aggregates. Additionally, we suggest to use the discrete element method to understand the particle rearrangement during the compaction process. This model is calibrated based on the SuperPave gyratory compaction tests in the pavement lab. In the end, we compared the model results to experimental data to show that this model prediction had a good agreement with the experiments, thus, had great potentials to be implemented to improve the design of asphalt mixtures.

Laboratory Assessment of Dense Graded Asphalt Concrete Incorporating Coal Furnace Ash in South of Vietnam

2021 ◽  
Vol 879 ◽  
pp. 117-125
Author(s):  
Dang Tung Dang ◽  
Manh Tuan Nguyen ◽  
Ngoc Tram Hoang ◽  
Anh Thang Le
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Coal Ash ◽  
Aggregate Size ◽  
Road Construction ◽  
Maximum Aggregate Size ◽  
Fine Aggregate ◽  
Laboratory Assessment ◽  
Laboratory Performance ◽  
Major Interest

Currently, application of industrial waste or by-product in road construction industrials is a major interest by researchers, government officers and engineers. Coal ashes by-product from industrial parks negatively impact environment, costly in treatment, and require large ground for disposing areas. Therefore, this paper proposes on using the coal ash from furnace products of an industrial park in South of Vietnam to be incorporated into dense graded asphalt concrete using Nominal Maximum Aggregate Size 12.5mm. Laboratory performance tests including Marshall stability, indirect tensile strength, Cantabro loss, and dynamic fatigue test were conducted. The effects of coal ash contents in replacement of fine aggregate which is passing 4.75mm sieve from asphalt mixture into laboratory performance of mixture is also discussed in detail.

Laboratory Investigate of the Effect of Fine Aggregates on Asphalt Mixture Materials

2011 ◽  
Vol 225-226 ◽  
pp. 577-580
Author(s):  
Yong Ye ◽  
Yi Zhou Cai
Keyword(s):  
Compressive Strength ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Fine Aggregate ◽  
Test Results ◽  
Creep Tests ◽  
Aggregate Gradation ◽  
Static Creep ◽  
Fine Aggregates

The objective of this study is to investigate and evaluate the effect of fine aggregates (aggregate size smaller than or equal to 2.36 mm) on the compressive strength and creep behavior of asphalt mixtures. The variables that are considered in the study include the sizes and gradations of fine aggregate. A kind of standant aggregate gradation and four kinds of reduced aggregate gradation mixture specimens are used. Uniaxial compression and static creep tests were realized at different loading conditions. The test results showed that the different fine aggregate sizes do not result in significant differences in compressive strength and creep values using the same percentage of fine aggregates (38.4%). Only the different gradations showed a little differences for mixtures made with different gradations but same aggregate size (between 2.36 and 1.18 mm).

Laboratory Study on Cold-Mixtures for Asphalt Pavement

2012 ◽  
Vol 178-181 ◽  
pp. 1361-1364
Author(s):  
Shi Bin Ma ◽  
Li Jie Wang ◽  
Guo Qiang Zhang
Keyword(s):  
Laboratory Study ◽  
Asphalt Concrete ◽  
Resilient Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Test Methods ◽  
Recycled Asphalt ◽  
Concrete Mixtures ◽  
Mechanistic Analysis ◽  
Cleavage Strength

The main purpose of recycling is to reuse existing pavement material. First this paper reviews the necessary, feasibility and mechanistic analysis of recycled asphalt mixture, then summarizes the findings of a laboratory study to characterize and design recycled asphalt concrete mixtures using different tests. The laboratory tests carried out on the material were conventional test methods including unconfined compressive strength, cleavage strength, resilient modulus and shrinkage properties tests. The results of the laboratory can be taken as reference in design, engineering and further research．

scholarly journals Investigating the Effect of Olive Husk Ash on the Properties of Asphalt Concrete Mixture

2021 ◽  
Vol 45 (1) ◽  
pp. 11-15
Author(s):  
Arabi N.S. Al Qadi ◽  
Taisir S. Khedaywi ◽  
Madhar A. Haddad ◽  
Owies A. Al-Rababa'ah
Keyword(s):  
Asphalt Concrete ◽  
Construction Material ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Concrete Mixture ◽  
Mineral Aggregate ◽  
Limestone Aggregate ◽  
Olive Husk ◽  
Pavement Construction ◽  
Marshall Stability

Technology in transportation used available resources to make it safe, fast, suitable, easy, economic, and environmental to transport people and goods. Olive Husk became an environmental problem as waste materials especially in the Middle East where huge quantities are found. The objective of this research is to investigate the effect of addition of Olive Husk Ash (OHA) on the properties of asphalt concrete mixtures. Marshall Test was used to perform the asphalt concrete mixture by the addition of OHA to the binder of asphalt; different percentages of OHA (0, 5, 10, 15, and 20%) by volume were added to the binder. Five percent of asphalt cements (5, 5.5, 6, 6.5 and 7%) by weight and limestone aggregate were used for preparing asphalt mixture specimens to find the optimum content of asphalt that could be used in the binder. Tests on flow, stability, air void percentage and void in mineral aggregate, retained stability, stiffness, and retained stiffness were made. The principle results on OHA as filler in Asphalt binder improves the Marshall Stability, and void in mineral aggregate and decrease in flow, retained stability, stiffness, and retained stiffness with a 10%-15% of olive husk ash replacement of asphalt binder. The contribution that OHA could be used as a pavement construction material in field.

EVALUATION ON THE PERFORMANCE OF AGED ASPHALT BINDER AND MIXTURE UNDER VARIOUS AGING METHODS

2015 ◽  
Vol 77 (23) ◽  
Author(s):  
Mohd Khairul Idham ◽  
Mohd Rosli Hainin ◽  
M. Naqiuddin M. Warid ◽  
Noor Azah Abdul Raman ◽  
Rosmawati Mamat
Keyword(s):  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Maximum Aggregate Size ◽  
Asphaltic Concrete ◽  
Air Exposure ◽  
Stiffness Modulus ◽  
Aged Asphalt

Hot mix asphalt (HMA) pavement encounter short and long term aging throughout the service life. Laboratory aging is the method used to simulate field aging process of HMA pavement. This study was undertaken to determine the long term effect of different binder and mixture laboratory aging methods on HMA (binder aging and mixture aging). Three types of HMA mixtures were prepared for this study namely Asphaltic Concrete with 10 mm nominal maximum aggregate size (AC 10), Asphaltic Concrete 14 mm (AC 14) and Asphaltic Concrete 28 mm (AC 28). These specimens were conditioned with nine different methods and durations.  Resilient modulus test was carried out at 40˚C as an initial indicator of the specimen performance. Permanent deformation of the same specimens was then evaluated by dynamic creep test. Generally, the aged asphalt binder specimens have higher resilient and stiffness modulus compared to aged asphalt mixture specimens. In addition, aged binder specimens have a lower permanent strain which indicates higher resistance to permanent deformation. This study also found that high resilient and stiffness modulus of specimens is attributed by different in heating frequency, temperature, air exposure and binder content of the mixtures.

Experimental Testing and Analysis Procedure to Determine the Apparent Film Thickness of Asphalt Binder in Fine Aggregate Matrix Mixtures

2021 ◽  
Vol 2675 (7) ◽  
pp. 166-179
Author(s):  
Lucas Henrique Vieira ◽  
Thiago Delgado de Souza ◽  
Alexis Jair Enríquez-León ◽  
Francisco Thiago Sacramento Aragão ◽  
Otávio da Fonseca Martins Gomes ◽  
...  
Keyword(s):  
Film Thickness ◽  
Asphalt Concrete ◽  
Experimental Testing ◽  
Asphalt Binder ◽  
Analysis Procedure ◽  
Fine Aggregate ◽  
Concrete Mixtures ◽  
Proper Design ◽  
Fine Aggregate Matrix ◽  
Imagej Software

The fine aggregate matrix (FAM) is an important constituent of an asphalt concrete mixture; the FAM is where some key damage phenomena such as cracking start and propagate. The proper design and fabrication of isolated FAM testing samples that are representative of the material existing within asphalt concrete mixtures requires the objective determination of key characteristics such as the apparent film thickness (FT) of the asphalt binder and the specific surface area of the aggregates. These relevant parameters facilitate the estimation of the binder content. This study presents an experimental testing and analysis protocol to determine the apparent FT that covers particles of fine aggregate in FAM mixtures. The method is based on tests using a scanning electron microscope and a digital image analysis procedure using the open-source Fiji/ImageJ software. The results indicated that apparent FT ranged between 0.5 µm and 30 µm. An additional validation effort was pursued and demonstrated the applicability of the proposed methodology, which can provide meaningful information to improve volumetric-based FAM mix design methods and generate materials that are more representative of those existing in the asphalt concrete mixtures.

Sign in / Sign up

Export Citation Format

Share Document