scholarly journals Solochrome Dark Blue Azo Dye Removal by Sonophotocatalysis Using Mn2+ Doped ZnS Quantum Dots

Catalysts ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1025
Author(s):  
Jyoti Patel ◽  
Ajaya K. Singh ◽  
Bhawana Jain ◽  
Sushma Yadav ◽  
Sónia A. C. Carabineiro ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Quantum Dots ◽  
Azo Dye ◽  
Frequency Effect ◽  
Active Surface Area ◽  
Average Particle ◽  
Ultrasonic Power ◽  
X Ray ◽  
Catalytic Material ◽  
Dark Blue

This work investigates the degradation of the azo dye solochrome dark blue (SDB) by measurement of the photocatalytic, sonocatalytic and sonophotocatalytic activities, under low ultrasonic frequency (40 kHz) and UV-C (254 nm) light, using Mn-doped ZnS semiconductor quantum dots (Mn2+:ZnS Qds) as catalysts, prepared by a simple chemical precipitation procedure. In order to study the different morphological and optical crystal properties, various characterization techniques were used, such as high resolution transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, N2 adsorption-desorption at −196 °C and ultraviolet-visible spectroscopy. The average particle size of the semiconductor Qds was in the range of 3–4 nm. The optimal parameters affecting dye degradation, such as the catalyst loading, solution pH, time of irradiation, initial concentration of dye, dopant concentration, ultrasonic power and frequency effect were evaluated. The synthesized catalytic material exhibited a high activity for sonophotocatalytic degradation of SDB (89%), larger than that observed for sonocatalysis (69.7%) or photocatalysis (55.2%) alone, which was due to the improved electron-holes separation, formation of more reactive radicals and enhancement of the active surface area. Qds showed good stability and reusability after five repeated cycles. Finally, the degradation products were identified by liquid chromatography-mass spectrometry (LC-MS).

Ni/MWCNT-Supported Palladium Nanoparticles as Magnetic Catalysts for Selective Oxidation of Benzyl Alcohol

2013 ◽  
Vol 66 (5) ◽  
pp. 564 ◽  
Author(s):  
Mingmei Zhang ◽  
Qian Sun ◽  
Zaoxue Yan ◽  
Junjie Jing ◽  
Wei Wei ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Benzyl Alcohol ◽  
Bimetallic Nanoparticles ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Oxidation Of Benzyl Alcohol ◽  
Uniform Dispersion ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

Well dispersed Pd@Ni bimetallic nanoparticles on multi-walled carbon nanotubes (Pd@Ni/MWCNT) are prepared and used as catalysts for the oxidation of benzyl alcohol. Scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy analysis, and X-ray diffraction were performed to characterise the synthesised catalyst. The results show a uniform dispersion of Pd@Ni nanoparticles on MWCNT with an average particle size of 4.0 nm. The as synthesised catalyst was applied to the oxidation of benzyl alcohol. A 99 % conversion of benzyl alcohol and a 98 % selectivity of benzaldehyde were achieved by using the Pd@Ni/MWCNT (Pd: 0.2 mmol) catalyst with water as a solvent and H2O2 as oxidant at 80°C. The catalytic activity of Pd@Ni/MWCNT towards benzyl alcohol is higher than that of a Pd/MWCNT catalyst at the same Pd loadings. The catalyst can be easily separated due to its magnetic properties.

Optical properties and energy transfer processes in Tb3+-doped ZnSe quantum dots

2021 ◽  
Author(s):  
Nguyen Ca ◽  
N. D Vinh ◽  
Phan Van Do ◽  
N. T. Hien ◽  
Xuan Hoa Vu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Quantum Dots ◽  
Chemical Method ◽  
X Ray Diffraction ◽  
Wet Chemical Method ◽  
X Ray ◽  
Transfer Processes ◽  
Transmission Electron ◽  
Wet Chemical

Tb3+-doped ZnSe quantum dots (QDs) with Tb content in the range of 0.5 - 7% were successfully synthesized by a wet chemical method. X-ray diffraction (XRD) and transmission electron microscopy...

scholarly journals Amorphous Ni x Co y P-supported TiO2 nanotube arrays as an efficient hydrogen evolution reaction electrocatalyst in acidic solution

2019 ◽  
Vol 10 ◽  
pp. 62-70 ◽  
Author(s):  
Yong Li ◽  
Peng Yang ◽  
Bin Wang ◽  
Zhongqing Liu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Hydrogen Evolution ◽  
Hydrogen Evolution Reaction ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Nanotube Arrays ◽  
Active Surface Area ◽  
X Ray ◽  
Transmission Electron

Bimetallic phosphides have been attracting increasing attention due to their synergistic effect for improving the hydrogen evolution reaction as compared to monometallic phosphides. In this work, NiCoP modified hybrid electrodes were fabricated by a one-step electrodeposition process with TiO2 nanotube arrays (TNAs) as a carrier. X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy and scanning transmission electron microscopy/energy-dispersive X-ray spectroscopy were used to characterize the physiochemical properties of the samples. The electrochemical performance was investigated by cyclic voltammetry, linear sweep voltammetry, and electrochemical impedance spectroscopy. We show that after incorporating Co into Ni–P, the resulting Ni x Co y P/TNAs present enhanced electrocatalytic activity due to the improved electron transfer and increased electrochemically active surface area (ECSA). In 0.5 mol L−1 H2SO4 electrolyte, the Ni x Co y P/TNAs (x = 3.84, y = 0.78) demonstrated an ECSA value of 52.1 mF cm−2, which is 3.8 times that of Ni–P/TNAs (13.7 mF cm−2). In a two-electrode system with a Pt sheet as the anode, the Ni x Co y P/TNAs presented a bath voltage of 1.92 V at 100 mA cm−2, which is an improvment of 79% over that of 1.07 V at 10 mA cm−2.

Microstructure characteristics of non-monodisperse quantum dots: on the potential of transmission electron microscopy combined with X-ray diffraction

CrystEngComm ◽  
2020 ◽  
Vol 22 (21) ◽  
pp. 3644-3655
Author(s):  
Stefan Neumann ◽  
Christina Menter ◽  
Ahmed Salaheldin Mahmoud ◽  
Doris Segets ◽  
David Rafaja
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Quantum Dots ◽  
Cdse Quantum Dots ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure Characteristics ◽  
Scale Bridging ◽  
Transmission Electron ◽  
Hot Injection

Capability of TEM and XRD to reveal scale-bridging information about the microstructure of non-monodisperse quantum dots is illustrated on the CdSe quantum dots synthesized using an automated hot-injection method.

scholarly journals Formation of ZnO/Zn0.5Cd0.5Se Alloy Quantum Dots in the Presence of High Oleylamine Contents

Nanomaterials ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 999
Author(s):  
Yi-An Chen ◽  
Kuo-Hsien Chou ◽  
Yi-Yang Kuo ◽  
Cheng-Ye Wu ◽  
Po-Wen Hsiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Quantum Dots ◽  
Particle Size ◽  
X Ray Diffraction ◽  
One Pot ◽  
X Ray ◽  
Transmission Electron ◽  
Average Size ◽  
Alloy Quantum Dots ◽  
First Time

To the best of our knowledge, this report presents, for the first time, the schematic of the possible chemical reaction for a one-pot synthesis of Zn0.5Cd0.5Se alloy quantum dots (QDs) in the presence of low/high oleylamine (OLA) contents. For high OLA contents, high-resolution transmission electron microscopy (HRTEM) results showed that the average size of Zn0.5Cd0.5Se increases significantly from 4 to 9 nm with an increasing OLA content from 4 to 10 mL. First, [Zn(OAc)2]–OLA complex can be formed by a reaction between Zn(OAc)2 and OLA. Then, Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) data confirmed that ZnO is formed by thermal decomposition of the [Zn(OAc)2]–OLA complex. The results indicated that ZnO grew on the Zn0.5Cd0.5Se surface, thus increasing the particle size. For low OLA contents, HRTEM images were used to estimate the average sizes of the Zn0.5Cd0.5Se alloy QDs, which were approximately 8, 6, and 4 nm with OLA loadings of 0, 2, and 4 mL, respectively. We found that Zn(OAc)2 and OLA could form a [Zn(OAc)2]–OLA complex, which inhibited the growth of the Zn0.5Cd0.5Se alloy QDs, due to the decreasing reaction between Zn(oleic acid)2 and Se2−, which led to a decrease in particle size.

Multiferroic Bismuth Ferrite Nanoparticles: Rapid Sintering Synthesis, Characterization, and Optical Properties

2010 ◽  
Vol 152-153 ◽  
pp. 81-85
Author(s):  
Xiong Wang ◽  
Yin Lin ◽  
Jin Guo Jiang
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Optical Properties ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Bifeo3 Nanoparticles ◽  
Rapid Sintering

The homogeneous multiferroic BiFeO3 nanoparticles with average particle size of 85 nm have been successfully synthesized by a simple sol-gel route. The prepared sample was characterized by a variety of techniques, such as X-ray diffractometry, thermogravimetric analysis and differential thermal analysis, differential scanning calorimeter analysis, scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The obtained results shows that rapid sintering and subsequently quenching to room temperature are the two vital important factors for the preparation of pure BiFeO3. The magnetic phase transition (TN = 369 °C) and the ferroelectric phase transition (TC = 824.5 °C) were determined, revealing the antiferromagnetic and ferroelectric nature of the as-prepared BiFeO3 nanoparticles. The optical properties of the nanopowders were investigated. The strong band-gap absorption at 486 nm (2.55 eV) of the BiFeO3 nanoparticles may bring some novel applications.

scholarly journals Hydrothermal synthesis of ZnO quantum dot/KNb3O8 nanosheet photocatalysts for reducing carbon dioxide to methanol

2017 ◽  
Vol 8 ◽  
pp. 2264-2270 ◽  
Author(s):  
Xiao Shao ◽  
Weiyue Xin ◽  
Xiaohong Yin
Keyword(s):  
Electron Microscopy ◽  
Quantum Dots ◽  
Uv Light ◽  
Formation Rate ◽  
X Ray Diffraction ◽  
Methanol Production ◽  
X Ray ◽  
Transmission Electron ◽  
Methanol Formation ◽  
Zno Quantum Dots

ZnO quantum dots and KNb3O8 nanosheets were synthesized by a two-step hydrothermal method for the photocatalytic reduction of CO2 to methanol where isopropanol is simultaneously oxidized to acetone . The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM) and UV–vis absorption spectroscopy (UV–vis). The photocatalytic activity of the materials was evaluated by formation rate of methanol under UV light irradiation at ambient temperature and pressure. The methanol formation rate of pure KNb3O8 nanosheets was found to be 1257.21 μmol/g/h, and after deposition of 2 wt % ZnO quantum dots on the surface of KNb3O8 nanosheets, the methanol production rate was found to increase to 1539.77 μmol/g/h. Thus, the ZnO quantum dots obviously prompted separation of charge carriers, which was explained by a proposed mechanism for this photocatalytic reaction.

Biosynthesis and Characterization of Copper Nanoparticles Using a Bioflocculant Extracted from Alcaligenis faecalis HCB2

2019 ◽  
Vol 11 (11) ◽  
pp. 1064-1070 ◽  
Author(s):  
Nkosinathi G. Dlamini ◽  
Albertus K. Basson ◽  
V. S. R. Rajasekhar Pullabhotla
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Copper Nanoparticles ◽  
Average Particle Size ◽  
Thermo Gravimetric Analysis ◽  
Average Particle ◽  
Gravimetric Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir

Bioflocculant from Alcaligenis faecalis HCB2 was used in the eco-friendly synthesis of the copper nanoparticles. Nanoparticles were characterized using a scanning electron microscope (SEM), transmission electron microscopy (TEM), UV-visible spectroscopy, thermo gravimetric analysis (TGA) and Fourier Transform Infrared Spectroscopy (FT-IR). The transmission electron microscopy images showed close to spherical shapes with an average particle size of ∼53 nm. Energy-dispersive X-ray spectroscopy analysis confirmed the presence of the Cu nanopartilces and also the other elements such as O, C, P, Ca, Cl, Na, K, Mg, and S originated from the bioflocculant. FT-IR results showed the presence of the –OH and –NH2 groups, aliphatic bonds, amide and Cu–O bonds. Powder X-ray diffraction peaks confirmed the presence of (111) and (220) planes of fcc structure at 2 of 33° and 47° respectively with no other impurity peaks.

Facile Synthesis and Characterization of Spinel NiFe2O4 Nanoparticles and Studies of Their Photocatalytic Activity for Oxidation of Alcohols

2020 ◽  
Vol 12 (3) ◽  
pp. 357-365 ◽  
Author(s):  
Xiangrong Ma ◽  
Rui Dang ◽  
Jieying Liu ◽  
Fang Yang ◽  
Huigui Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray ◽  
Bet Analysis ◽  
Oxidation Of Alcohols ◽  
20 Nm ◽  
Adsorption Desorption

In this paper, we report a novel and facile approach for the synthesis of spinel NiFe2O4 nanoparticles and studies of its photocatalytic activity for oxidation of alcohols. The as-synthesized catalyst was thoroughly characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), elemental mapping, transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), and N2 adsorption–desorption isotherm (BET) analysis. The TEM image reveals cubic shapes with an average particle size of 10–20 nm. The as-synthesized spinel NiFe2O4 has proved to be an excellent photocatalyst for oxidation of alcohol to the aldehyde with a conversion of 80% and selectivity of 99%. The catalyst has also proved to be noteworthy as it does not loss its catalytic activity even after five cycles of reuse.

Sign in / Sign up

Export Citation Format

Share Document