scholarly journals The Effect of Transition Metal Substitution in the Perovskite-Type Oxides on the Physicochemical Properties and the Catalytic Performance in Diesel Soot Oxidation

Catalysts ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1256
Author(s):  
Liliya V. Yafarova ◽  
Grigory V. Mamontov ◽  
Irina V. Chislova ◽  
Oleg I. Silyukov ◽  
Irina A. Zvereva
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Simultaneous Thermal Analysis ◽  
Cobalt Content ◽  
Soot Oxidation ◽  
Substitution Effect ◽  
Catalytic Performance ◽  
Oxygen Mobility ◽  
X Ray ◽  
Temperature Programmed

The paper is focused on the Fe for Co substitution effect on the redox and catalytic properties in the perovskite structure of GdFeO3. The solid oxides with the composition GdFe1−xCoxO3 (x = 0; 0.2; 0.5; 0.8; 1) were obtained by the sol-gel method and characterized by various methods: X-Ray diffraction (XRD), temperature-programmed reduction (H2-TPR), N2 sorption, temperature-programmed desorption of oxygen (TPD-O2), simultaneous thermal analysis (STA), and X-ray photoelectron spectroscopy (XPS). The H2-TPR results showed that an increase in the cobalt content in the GdFe1−xCoxO3 (x = 0; 0.2; 0.5; 0.8; 1) leads to a decrease in the reduction temperature. Using the TPD-O2 and STA methods, the lattice oxygen mobility is increasing in the course of the substitution of Fe for Co. Thus, the Fe substitution in the perovskite leads to an improvement in the oxygen reaction ability. Experiments on the soot oxidation reveal that catalytic oxidation ability increases in the series: GdFe0.5Co0.5O3 ˂ GdFe0.2Co0.8O3 ˂ GdCoO3, which is in good correlation with the increasing oxygen mobility according to H2-TPR, TPD-O2, and STA results. The soot oxidation over GdFeO3 and GdFe0.8Co0.2O3 is not in this range due to the impurities of iron oxides and higher specific surface area.

scholarly journals Synthesis and Catalytic Performance of Ni/SiO2for Hydrogenation of 2-Methylfuran to 2-Methyltetrahydrofuran

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Fu Ding ◽  
Yajing Zhang ◽  
Guijin Yuan ◽  
Kangjun Wang ◽  
Ileana Dragutan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Content ◽  
Transmission Electron ◽  
Temperature Programmed ◽  
Ni Species

A series of Ni/SiO2catalysts with different Ni content were prepared by sol-gel method for application in the synthesis of 2-methyltetrahydrofuran (2-MTHF) by hydrogenation of 2-methylfuran (2-MF). The catalyst structure was investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and temperature programmed reduction (TPR). It is found that structures and catalytic performance of the catalysts were highly affected by the Ni content. The catalyst with a 25% Ni content had an appropriate size of the Ni species and larger BET surface area and produced a higher 2-MF conversion with enhanced selectivity in 2-MTHF.

Preparation of Novel Ag–Si–TiO2 Composite and Research on Its Photocatalytic Degradation of Formaldehyde

2021 ◽  
Vol 13 (3) ◽  
pp. 371-380
Author(s):  
Yongjun Wu ◽  
Nina Xie ◽  
Lu Yu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Removal Rate ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Formaldehyde Concentration ◽  
Order Kinetic ◽  
Solution Ph ◽  
Visible Absorption ◽  
X Ray ◽  
Co Doped

A novel Ag–Si–TiO2 composite was prepared via sol–gel method for removing residual formaldehyde in shiitake mushroom. The structure of Ag–Si–TiO2 composite was characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. Ultraviolet-visible absorption spectroscopy (UV-Vis) and N2 adsorption-desorption tests showed that Ag and Si co-doped decreased the band gap, the Brunauer-Emmett-Teller (BET) specific surface area of the samples increased and the recombination probability of electron-hole pairs (e--h+) reduced. Effect on removal rate of formaldehyde with different Ag-Si co-doped content, formaldehyde concentration and solution pH were investigated, and the results showed that 6.0 wt%Ag-3.0 wt%Si-TiO2 samples had an optimum catalytic performance, and the degradation efficiency reached 96.6% after 40 W 365 nm UV lamp irradiation for 360 min. The kinetics of formaldehyde degradation by Ag–Si–TiO2 composite photocatalyst could be described by Langmuir-Hinshelwood first-order kinetic model.

scholarly journals Influence of Sulfur-Containing Sodium Salt Poisoned V2O5–WO3/TiO2 Catalysts on SO2–SO3 Conversion and NO Removal

Catalysts ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 541 ◽  
Author(s):  
Haiping Xiao ◽  
Chaozong Dou ◽  
Hao Shi ◽  
Jinlin Ge ◽  
Li Cai
Keyword(s):  
Photoelectron Spectroscopy ◽  
No Reduction ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Impregnation Method ◽  
So2 Oxidation ◽  
Sodium Salts ◽  
X Ray ◽  
Temperature Programmed ◽  
Physical Features

A series of poisoned catalysts with various forms and contents of sodium salts (Na2SO4 and Na2S2O7) were prepared using the wet impregnation method. The influence of sodium salts poisoned catalysts on SO2 oxidation and NO reduction was investigated. The chemical and physical features of the catalysts were characterized via NH3-temperature programmed desorption (NH3-TPD), H2-temperature programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FT-IR). The results showed that sodium salts poisoned catalysts led to a decrease in the denitration efficiency. The 3.6% Na2SO4 poisoned catalyst was the most severely deactivated with denitration efficiency of only 50.97% at 350 °C. The introduction of SO42− and S2O72− created new Brønsted acid sites, which facilitated the adsorption of NH3 and NO reduction. The sodium salts poisoned catalysts significantly increased the conversion of SO2–SO3. 3.6%Na2S2O7 poisoned catalyst had the strongest effect on SO2 oxidation and the catalyst achieved a maximum SO2–SO3-conversion of 1.44% at 410 °C. Characterization results showed sodium salts poisoned catalysts consumed the active ingredient and lowered the V4+/V5+ ratio, which suppressed catalytic performance. However, they increased the content of chemically adsorbed oxygen and the strength of V5+=O bonds, which promoted SO2 oxidation.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals Generalized Methodology for Inserting Metal Heteroatoms into the Layered Zeolite Precursor RUB-36 by Interlayer Expansion

Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 530 ◽  
Author(s):  
Chaoqun Bian ◽  
Xiao Wang ◽  
Lan Yu ◽  
Fen Zhang ◽  
Jie Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Catalytic Performance ◽  
X Ray Diffraction ◽  
Zeolite Sample ◽  
X Ray ◽  
Inductively Coupled ◽  
Temperature Programmed ◽  
First Time ◽  
N2 Sorption

The incorporation of metal heteroatoms into zeolites is an effective modification strategy for enhancing their catalytic performance. Herein, for the first time we report a generalized methodology for inserting metal heteroatoms (such as Sn, Fe, Zn, and Co) into the layered zeolite precursor RUB-36 via interlayer expansion by using the corresponding metal acetylacetate salt. Through this generalized methodology, Sn-JHP-1, Fe-JHP-1, Zn-JHP-1 and Co-JHP-1 zeolites could be successfully prepared by the reaction of RUB-36 and corresponding metal acetylacetate salt at 180 °C for 24 h in the presence of HCl solution. As a typical example, Sn-JHP-1 and calcined Sn-JHP-1 (Sn-JHP-2) zeolite is well characterized by the X-ray diffraction (XRD), diffuse reflectance ultraviolet-visible (UV-Vis), inductively coupled plasma (ICP), N2 sorption, temperature-programmed-desorption of ammonia (NH3-TPD) and X-ray photoelectron spectroscopy (XPS) techniques, which confirm the expansion of adjacent interlayers and thus the incorporation of isolated Sn sites within the zeolite structure. Notably, the obtained Sn-JHP-2 zeolite sample shows enhanced catalytic performance in the conversion of glucose to levulinic acid (LA) reaction.

scholarly journals Synthesis of DME by CO2 hydrogenation over La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts

2017 ◽  
Vol 23 (1) ◽  
pp. 49-56 ◽  
Author(s):  
Yajing Zhang ◽  
Yu Zhang ◽  
Fu Ding ◽  
Kangjun Wang ◽  
Wang Xiaolei ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Direct Synthesis ◽  
Catalytic Performance ◽  
Co2 Hydrogenation ◽  
Precipitation Method ◽  
X Ray ◽  
Temperature Programmed ◽  
And Performance ◽  
Co Precipitation ◽  
Adsorption Desorption

A series of La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts were prepared by an oxalate co-precipitation method. The catalysts were fully characterized by X-ray diffraction (XRD), N2 adsorption-desorption, hydrogen temperature pro-grammed reduction (H2-TPR), ammonia temperature programmed desorption (NH3-TPD), and X-ray photoelectron spectroscopy (XPS) techniques. The effect of the La2O3 content on the structure and performance of the catalysts was thoroughly investigated. The catalysts were evaluated for the direct synthesis of dimethyl ether (DME) from CO2 hydrogenation. The results displayed that La2O3 addition enhanced catalytic performance, and the maximal CO2 conversion (34.3%) and DME selectivity (57.3%) were obtained over the catalyst with 1% La2O3, which due to the smaller size of Cu species and a larger ratio of Cu+/Cu.

Preparation and Characterization of Ni-Modified Fe-Mo and Catalytic Selective Oxidation of p-Xylene

2012 ◽  
Vol 557-559 ◽  
pp. 1501-1504 ◽  
Author(s):  
Zu Zeng Qin ◽  
Zi Li Liu ◽  
Yan Bin Liu ◽  
Rui Wen Liu
Keyword(s):  
Photoelectron Spectrum ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Ni Catalyst ◽  
Temperature Programmed Reduction ◽  
X Ray ◽  
Mo Catalyst ◽  
Ft Ir ◽  
Temperature Programmed

The preparation of the Fe-Mo-Ni catalyst using the sol-gel method was investigated. In addition, the catalytic selective oxidations of p-xylene (PX) to terephthalaldehyde (TPAL) on the Fe-Mo-Ni catalyst were also investigated. The catalysts were characterized using thermal analysis, H2-temperature programmed reduction (H2-TPR), Fourier transform infrared spectra (FT-IR), and X-ray photoelectron spectrum (XPS). The additional of Ni improves the catalytic activity of the Fe-Mo catalyst on selective oxidations of PX to TPAL. The optimal additive amount of Ni is 5%. XPS analysis shows that the introduction of Ni changes the internal structure of the Fe-Mo catalyst improves catalytic performance.

scholarly journals Cobalt Based Catalysts Supported on Two Kinds of Beta Zeolite for Application in Fischer-Tropsch Synthesis

Catalysts ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 497 ◽  
Author(s):  
Renata Sadek ◽  
Karolina A. Chalupka ◽  
Pawel Mierczynski ◽  
Jacek Rynkowski ◽  
Jacek Gurgul ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Performance ◽  
Tropsch Synthesis ◽  
Zeolite Catalysts ◽  
Beta Zeolite ◽  
Fischer Tropsch ◽  
Fischer Tropsch Synthesis ◽  
X Ray ◽  
Liquid Products ◽  
Temperature Programmed

Co-containing Beta zeolite catalysts prepared by a wet impregnation and two-step postsynthesis method were investigated. The activity of the catalysts was examined in Fischer-Tropsch synthesis (FTS), performed at 30 atm and 260 °C. The physicochemical properties of all systems were investigated by means of X-ray diffraction (XRD), in situ XRD, temperature programmed desorption of ammonia (NH3-TPD), X-ray Photoelectron Spectroscopy (XPS), temperature programmed reduction of hydrogen (TPR-H2), and transmission electron microscopy (TEM). Among the studied catalysts, the best results were obtained for the samples prepared by a two-step postsynthesis method, which achieved CO conversion of about 74%, and selectivity to liquid products of about 86%. The distribution of liquid products for Red-Me-Co20Beta was more diversified than for Red-Mi-Co20Beta. It was observed that significant influence of the zeolite dealumination of mesoporous zeolite on the catalytic performance in FTS. In contrast, for microporous catalysts, the dealumination did not play such a significant role and the relatively high activity is observed for both not dealuminated and dealuminated catalysts. The main liquid products of FTS on both mesoporous and microporous catalysts were C10-C14 isoalkanes and n-alkanes. The iso-/n-alkanes ratio for dealuminated zeolite catalysts was three times higher than that for not dealuminated ones, and was related to the presence of different kind of acidic sites in both zeolite catalysts.

Mesoporous phosphated and sulphated silica as solid acid catalysts for glycerol acetylation

2014 ◽  
Vol 68 (9) ◽  
Author(s):  
Khadijeh Ghoreishi ◽  
Nilofar Asim ◽  
Mohd Yarmo ◽  
Mohd Samsudin
Keyword(s):  
Photoelectron Spectroscopy ◽  
Solid Acid ◽  
Sol Gel ◽  
Acid Catalysts ◽  
X Ray ◽  
Bet Method ◽  
Ft Ir ◽  
Temperature Programmed ◽  
Catalyst Acidity ◽  
Glycerol Esterification

AbstractSulphate- and phosphate-loaded silicas were synthesised using the sol-gel method with different sulphate and phosphate loadings. These catalysts were characterised using Fourier transform infrared spectroscopy (FT-IR), the Brunauer-Emmett-Teller (BET) method and X-ray photoelectron spectroscopy (XPS). Acidity was measured using the temperature-programmed desorption of ammonia (TPD-NH3) method. The results showed that glycerol esterification with acetic acid conversion decreased as follows: α(H2SO4) (100 %) > α(H3PO4) (99 %) > α(silica loaded with 20 % sulphuric acid) (SS-20; 98 %) > α(silica loaded with 20 % phosphoric acid) (PS-20; 83 %). These studies suggest that the solid acid catalytic activity in the esterification of glycerol is highly dependent on catalyst acidity strength, pore size and surface area.

scholarly journals Effect of Copper Nanoparticles Dispersion on Catalytic Performance of Cu/SiO2Catalyst for Hydrogenation of Dimethyl Oxalate to Ethylene Glycol

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Yajing Zhang ◽  
Na Zheng ◽  
Kangjun Wang ◽  
Sujuan Zhang ◽  
Jing Wu
Keyword(s):  
Ethylene Glycol ◽  
Copper Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
X Ray ◽  
Dimethyl Oxalate ◽  
Effect Of Copper ◽  
Average Size

Cu/SiO2catalysts, for the synthesis of ethylene glycol (EG) from hydrogenation of dimethyl oxalate (DMO), were prepared by ammonia-evaporation and sol-gel methods, respectively. The structure, size of copper nanoparticles, copper dispersion, and the surface chemical states were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), temperature-programmed reduction (TPR), and X-ray photoelectron spectroscopy (XPS) and N2adsorption. It is found the structures and catalytic performances of the catalysts were highly affected by the preparation method. The catalyst prepared by sol-gel method had smaller average size of copper nanoparticles (about 3-4 nm), better copper dispersion, higher Cu+/C0ratio and larger BET surface area, and higher DMO conversion and EG selectivity under the optimized reaction conditions.

Sign in / Sign up

Export Citation Format

Share Document