scholarly journals Microstructural Characterization and Corrosion-Resistance Behavior of Dual-Phase Steels Compared to Conventional Rebar

Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1068
Author(s):  
Hany S. Abdo ◽  
Asiful H. Seikh ◽  
Biplab Baran Mandal ◽  
Jabair A. Mohammed ◽  
Sameh A. Ragab ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Galvanic Corrosion ◽  
Microstructural Characterization ◽  
Carbon Steels ◽  
Dual Phase ◽  
Low Carbon ◽  
Dp Steel ◽  
Dp Steels ◽  
Superior Corrosion Resistance ◽  
Corrosive Environments

Dual-phase (DP) steels consist of a ferritic matrix dispersed with some percentage of martensite, which gives the material a good combination of strength and ductility, along with the capacity to absorb energy and enhanced corrosion protection properties. The purpose of this work was to study the microstructural and corrosion behavior (mainly pitting and galvanic corrosion) of DP steel compared with that of conventional rebar. To obtain DP steel, low-carbon steels were heat-treated at 950 °C for 1 h and then intercritically annealed at 771 °C for 75 min, followed by quenching in ice-brine water. The corrosion rates of DP steel and standard rebar were then measured in different pore solutions. Macro- and microhardness tests were performed for both steels. It was found that DP steels exhibited a superior corrosion resistance and strength compared to standard rebar. The reported results show that DP steels are a good candidate for concrete reinforcement, especially in aggressive and corrosive environments.

MITTAL DI-FORM T700, HF80Y100T

Alloy Digest ◽  
2007 ◽  
Vol 56 (2) ◽  
Keyword(s):  
Automotive Industry ◽  
High Strength ◽  
Martensite Phase ◽  
Carbon Steels ◽  
Ferrite Phase ◽  
Dual Phase ◽  
Low Carbon ◽  
Advanced High Strength Steel ◽  
Dp Steels ◽  
Soft Ferrite

Abstract MITTAL DI-FORM T700 and HF80Y100T are low-carbon steels with a manganese and silicon composition. Dual-phase (DP) steels are one of the important advanced high-strength steel (AHSS) products developed for the automotive industry. Their microstructure typically consists of a soft ferrite phase with dispersed islands of a hard martensite phase. The martensite phase is substantially stronger than the ferrite phase. The DI-FORM grades exhibit low yield-to-tensile strengths, and the numeric designation in the name corresponds to the tensile strength. This datasheet provides information on microstructure and tensile properties as well as deformation and fatigue. It also includes information on forming. Filing Code: SA-561. Producer or source: Mittal Steel USA Flat Products.

Study of Recrystallization and Phase Transformation in a Cold-Rolled Dual-Phase Steel: Influence of Temperature and Heating Rate during First Annealing Stages

2011 ◽  
Vol 702-703 ◽  
pp. 818-821 ◽  
Author(s):  
Carla Barbatti ◽  
Patricia Romano Triguero ◽  
Stefan Van Bohemen ◽  
Steven Celotto ◽  
Dave N. Hanlon
Keyword(s):  
Heating Rate ◽  
Dual Phase Steel ◽  
Dual Phase ◽  
Low Carbon ◽  
Dp Steel ◽  
Influence Of Temperature ◽  
Individual Contributions ◽  
Cold Rolled ◽  
Dp Steels ◽  
The Individual

The effect of heating path and heating rate on the microstructure and texture development in cold-rolled continuously annealed DP steel was studied by SEM and EBSD. A methodology to separate the individual phases present in mixed microstructures, and thus to enable quantification of the individual contributions to the bulk texture has been applied. It was observed that a higher heating rate may promote strengthening of {111} textures in DP steels as observed in low carbon grades.

scholarly journals Spheroidization heat treatment and intercritical annealing of low carbon steel

2019 ◽  
Vol 55 (3) ◽  
pp. 405-411 ◽  
Author(s):  
Z. Nasiri ◽  
H. Mirzadeh
Keyword(s):  
Carbon Steel ◽  
Intercritical Annealing ◽  
Low Carbon Steel ◽  
Dual Phase ◽  
Low Carbon ◽  
Dp Steel ◽  
Martensitic Microstructure ◽  
Uniform Dispersion ◽  
Dp Steels ◽  
Carbide Particles

Spheroidization annealing of low carbon steel and its effects on the microstructure and mechanical properties of dual phase (DP) steel were studied. It was revealed that the reduction in strength and hardness of the quenched martensitic microstructure was much more pronounced compared to the fully annealed ferritic-pearlitic banded microstructure with spheroidizing time. This was related to the confinement of spheroidized carbide particles to distinct bands in the latter, and the uniform dispersion of carbides and high-temperature tempering of martensite in the former. During intercritical annealing of the spheroidized microstructures, the tendency to obtain martensite particles as discrete islands was observed. This, in turn, resulted in an inferior strength-ductility balance compared to the DP steel obtained from the intercritical annealing of martensite, which negated the usefulness of the spheroidized microstructures as the initial microstructures for the processing of DP steels.

MITTAL DI-FORM 140T, HB T965

Alloy Digest ◽  
2007 ◽  
Vol 56 (4) ◽  
Keyword(s):  
Tensile Strength ◽  
Yield Strength ◽  
Martensite Phase ◽  
Carbon Steels ◽  
Ferrite Phase ◽  
Dual Phase ◽  
Low Carbon ◽  
Dp Steel ◽  
Low Carbon Steels ◽  
Soft Ferrite

Abstract MITTAL DI-FORM 140T and HB T965 are low carbon steels with dual phase manganese and silicon composition. Dual-phase (DP) steel microstructures typically consist of a soft ferrite phase with dispersed islands of a hard martensite phase. The martensite phase is substantially stronger than the ferrite phase. The dual-phase grades, including those with high tensile strengths of 965 MPa (140 ksi), that are designed for forming (DI-FORM), also have low yield-strength-to-tensile-strength ratios to improve formability. This datasheet provides information on microstructure and tensile properties as well as deformation and fatigue. It also includes information on forming and surface treatment. Filing Code: SA-566. Producer or source: Mittal Steel USA Flat Products.

ALLEGHENY STAINLESS TYPE 434

Alloy Digest ◽  
1974 ◽  
Vol 23 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Heat Treating ◽  
Low Carbon ◽  
Good Corrosion Resistance ◽  
Temperature Performance ◽  
Continuous Service ◽  
Oxidation Resistant ◽  
Corrosive Environments

Abstract ALLEGHENY STAINLESS TYPE 434 is a low-carbon ferritic stainless steel with good corrosion resistance to mildly corrosive environments and the atmosphere. It is oxidation resistant at temperatures up to 1600 F for intermittent service and up to 1450-1500 F for continuous service. It is used for automotive trim and other exterior environments. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness and fatigue. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-292. Producer or source: Allegheny Ludlum Corporation.

OUTOKUMPU MODA 410L/4003

Alloy Digest ◽  
2020 ◽  
Vol 69 (12) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Ferritic Stainless Steel ◽  
Low Cost ◽  
Heat Treating ◽  
Low Carbon ◽  
Alloy Steels ◽  
Corrosive Environments

Abstract Outokumpu Moda 410L/4003 is a weldable, extra low carbon, Cr-Ni, ferritic stainless steel that is best suited for mildly corrosive environments such as indoors, where the material is either not exposed to contact with water or gets regularly wiped dry, or outdoors, where some discoloration and superficial rusting are acceptable. It is a low-cost alternative to low-carbon non-alloy steels in certain applications. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-1330. Producer or source: Outokumpu Oyj.

OUTOKUMPU MODA 410S/4000

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Low Carbon ◽  
Good Resistance ◽  
Temperature Performance ◽  
Corrosive Environments

Abstract Outokumpu Moda 410S/4000 is a 13% Cr, ferritic stainless steel that is used in applications requiring good resistance to mildly corrosive environments. It is a low carbon, non-hardening modification of Type 410 stainless steel. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on low and high temperature performance, corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-1329. Producer or source: Outokumpu Oyj.

scholarly journals Pitting Corrosion Resistance and Repassivation Behavior of C-Bearing Duplex Stainless Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 930 ◽  
Author(s):  
Hanme Yoon ◽  
Heon-Young Ha ◽  
Tae-Ho Lee ◽  
Sung-Dae Kim ◽  
Jae Hoon Jang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Pitting Corrosion ◽  
Galvanic Corrosion ◽  
Dual Phase ◽  
Corrosion Resistant ◽  
Grain Sizes ◽  
Α Phase ◽  
Pitting Corrosion Resistance ◽  
Corrosion Pits ◽  
Pit Initiation

The effects of C-substitution for part of the N content, on the pitting corrosion resistance and repassivation tendencies of duplex stainless steels (DSSs) were investigated. For this investigation, normal UNS S32205 containing N only (DSS-N) and the C-substituted DSS (DSS-NC) were fabricated. Microstructural analyses confirmed that the two DSSs had dual-phase microstructures without precipitates, and they possessed similar initial microstructure, including their grain sizes and phase fractions. Polarization and immersion tests performed in concentrated chloride solutions revealed that the DSS-NC was more resistant against stable pitting corrosion and possessed a higher repassivation tendency than the DSS-N. Furthermore, the corrosion pits initiated and propagated to a less corrosion resistant α phase. Polarization tests and corrosion depth measurements conducted in an HCl solution indicated that the DSS-NC exhibited lower galvanic corrosion rate between the α and γ phases than the DSS-N. Therefore, the growth rate of pit embryo was lowered in the DSS-NC, which shifted the potentials for the stable pit initiation and the pit extinction to the higher values.

scholarly journals Effect of Martensite Morphologies on Corrosion in 5% H2SO4 Solution of Borided X70 Dual Phase Steel

2021 ◽  
Vol 45 (1) ◽  
pp. 69-74
Author(s):  
Tassi Hocine ◽  
Zidelmel Sami ◽  
Allaoui Omar
Keyword(s):  
Corrosion Resistance ◽  
Dual Phase Steel ◽  
Annealing Temperature ◽  
Intercritical Annealing ◽  
Ferrite Matrix ◽  
Dual Phase ◽  
H2so4 Solution ◽  
Dp Steel ◽  
Direct Quenching ◽  
Step Quenching

In the present investigation, some electrochemical properties of dual phase X70 steels with different martensite morphologies which have undergone boriding were studied. To obtain a variety of martensite morphologies, Direct Quenching (DQ), Intermediate Quenching (IQ) and Step Quenching (SQ) heat treatments were applied at an intercritical annealing temperature (IAT) of 760℃. The treatment (DQ) allowed the formation of fine martensite evenly distributed in the ferrite matrix. (IQ) treatment showed the formation of martensite along the ferrite / ferrite grain boundaries. In contrast, treatment (SQ) induced the formation of a banded morphology of martensite and ferrite. The realization of borides on X70 (DP) steel was carried out in a powder mixture containing 5% of B4C as source of boron, 5% of NaBF4 as activator and 90% of SiC as diluent at 950℃ for a period of time from 4 h. The corrosion behavior of X70 (DP) steel has been explored by the Tafel extrapolation method in a 5 wt. % H2SO4 solution. The corrosion resistance of steel which has undergone boriding (BDP) is higher than that of steel which has not undergone it (DP).

scholarly journals Austenite Reverse Transformation in a Q&P Route of Mn and Ni Added Steels

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 862 ◽  
Author(s):  
Maribel Arribas ◽  
Teresa Gutiérrez ◽  
Eider Del Molino ◽  
Artem Arlazarov ◽  
Irene De Diego-Calderón ◽  
...  
Keyword(s):  
Microstructure Evolution ◽  
Microstructural Characterization ◽  
Carbon Steels ◽  
Reverse Transformation ◽  
Low Carbon ◽  
Effective Mechanism ◽  
Low Carbon Steels ◽  
Heat Treated ◽  
Final Microstructure

In this work, four low carbon steels with different contents of Mn and Ni were heat treated by quenching and partitioning (Q&P) cycles where high partitioning temperatures, in the range of 550 °C–650 °C, were applied. In order to elucidate the effect of applying these high partitioning temperatures with respect to more common Q&P cycles, the materials were also heat treated considering a partitioning temperature of 400 °C. The microstructure evolution during the Q&P cycles was studied by means of dilatometry tests. The microstructural characterization of the treated materials revealed that austenite retention strongly depended on the alloy content and partitioning conditions. It was shown that the occurrence of austenite reverse transformation (ART) in the partitioning stage in some of the alloys and conditions was a very effective mechanism to increase the austenite content in the final microstructure. However, the enhancement of tensile properties achieved by the application of high partitioning temperature cycles was not significant.

Sign in / Sign up

Export Citation Format

Share Document