scholarly journals Compact Printable Inverted-M Shaped Chipless RFID Tag Using Dual-Polarized Excitation

Electronics ◽  
2019 ◽  
Vol 8 (5) ◽  
pp. 580 ◽  
Author(s):  
Wazie M. Abdulkawi ◽  
Abdel-Fattah A. Sheta ◽  
Khaled Issa ◽  
Saleh A. Alshebeili
Keyword(s):  
Frequency Band ◽  
Radio Frequency Identification ◽  
Length Variation ◽  
Detection Capability ◽  
Rfid Tag ◽  
Chipless Rfid ◽  
Data Density ◽  
Frequency Identification ◽  
Experimental Errors ◽  
Dual Polarized

A novel and compact dual-polarized (DP) chipless radio-frequency identification (RFID) tag is presented in this paper. This tag can read both vertical and horizontal orientations within its frequency band, which improves the robustness and detection capability of the RFID system. The proposed tag makes use of the slot length variation encoding technique to improve the encoding capacity. This technique can duplicate the encoding capacity, thereby reducing the overall tag size by almost 50%. In particular, the proposed tag has an encoding capacity of 20 bits in the 3–8 GHz frequency band and achieves data density of around 15.15 bits/cm2. Three prototypes are fabricated and tested outside an anechoic chamber. Furthermore, one tag is tested at different distances (10 cm, 30 cm, and 60 cm) from the reader and the measured results are compared. The simulated and measured results are in reasonable agreement, with acceptable shifts at some frequencies due to fabrication and experimental errors.

scholarly journals On the application of the EM-imaging for chipless RFID tags

2015 ◽  
Vol 2 (2) ◽  
pp. 86-96 ◽  
Author(s):  
M. Zomorrodi ◽  
N.C. Karmakar
Keyword(s):  
Radio Frequency Identification ◽  
Low Cost ◽  
60 Ghz ◽  
Rfid Tag ◽  
High Data ◽  
Data Encoding ◽  
Bending Effect ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Cost Item

The electromagnetic (EM) imaging technique at mm-band 60 GHz is proposed for data encoding purpose in the chipless Radio Frequency Identification (RFID) systems. The fully printable chipless RFID tag comprises tiny conductive EM polarizers to create high cross-polar radar cross-section. Synthetic aperture radar approach is applied for formation of the tag's EM-image and revealing the tag's content. The achieved high data encoding capacity of 2 bits/cm2in this technique based on a fully printable tag is very convincing for many applications. The system immunity to multipath interference, bending effect, and printing inaccuracy suggests huge potentials for low-cost item tagging. Tags are also readable through a tick paper envelop; hence secure identification is provided by the proposed technique.

A low-profile FSS-based high capacity chipless RFID tag for sensing and encoding applications

2021 ◽  
pp. 1-9
Author(s):  
Shahid Habib ◽  
Amjad Ali ◽  
Ghaffer Iqbal Kiani ◽  
Wagma Ayub ◽  
Syed Muzahir Abbas ◽  
...  
Keyword(s):  
Radio Frequency Identification ◽  
High Capacity ◽  
Frequency Selective Surface ◽  
Rfid Tag ◽  
Sensing Applications ◽  
Low Profile ◽  
Simple Geometry ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Good Agreement

Abstract This paper presents a polarization-independent 11-bit chipless RFID tag based on frequency-selective surface which has been designed for encoding and relative humidity (RH) sensing applications. The 10 exterior U-shaped resonators are used for item encoding whereas Kapton has been incorporated with the interior resonator for RH sensing. This radio-frequency identification (RFID) tag operates in S- and C-frequency bands. The proposed design offers enhanced fractional bandwidth up to 88% with the density of 4.46 bits/cm2. Both single- and dual-layer tags have been investigated. The simulated results are in good agreement with measured results and a comparison with existing literature is presented to show the performance. Simple geometry, high code density, large frequency signature bandwidth, high magnitude bit, high radar cross-section, and angular stability for more than 75° are the unique outcomes of the proposed design. In addition, RH sensing has been achieved by integrating the Kapton on the same RFID tag.

Investigation on the chipless RFID tag with a UWB pulse using a UWB IR-based reader

2021 ◽  
pp. 1-10
Author(s):  
Kawther Mekki ◽  
Omrane Necibi ◽  
Hugo Dinis ◽  
Paulo Mendes ◽  
Ali Gharsallah
Keyword(s):  
Radio Frequency Identification ◽  
Ultra Wideband ◽  
Rfid Tag ◽  
Triangular Patch ◽  
Chipless Rfid ◽  
Frequency Domains ◽  
Measurement Results ◽  
Reader Antenna ◽  
Frequency Identification ◽  
Working Principle

Abstract In order to encrypt/encode data based on the magnitude level of the radar cross-section (RCS), we propose an approach with a precise estimation considering the resonant characteristics of a multipatch backscatter-based chipless radio frequency identification (RFID) dedicated for chipless tags depolarization. The working principle is based on the polarization mismatch between the tag and the reader antenna to control the magnitude of the backscatter, which allows a reliable detection in real environments. We introduce in this paper a new 4-bit chipless RFID tag with an enhanced RCS, based on a triangular patch antenna with multiple resonators. Additionally, we propose an ultra-wideband impulse radar (UWB-IR)-based reader that interrogates the chipless tag with a UWB pulse, and the received backscatter was studied in both time- and frequency-domains. The antenna was operating from 4.7 to 6.1 GHz, a band allocated for RFID systems. The obtained experimental measurement results in the environment of anechoic chamber were exceptionally relevant to validate the simulation results.

scholarly journals Miniaturized Chipless RFID Tags Based on Periodically Loaded Microstrip Structure

2019 ◽  
Vol 9 (5) ◽  
pp. 4679-4684
Author(s):  
M. Added ◽  
K. Rabaani ◽  
S. Chabaan ◽  
N. Boulejfen
Keyword(s):  
Radio Frequency Identification ◽  
Low Cost ◽  
Resonant Circuit ◽  
Rfid Tags ◽  
Frequency Range ◽  
Rfid Tag ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Coding Capacity ◽  
Microstrip Structure

A compact chipless radio frequency identification (RFID) tag-based on slow-wave technology is introduced in this paper. The tag consists of a resonant circuit based on open stub resonators periodically loaded by shunt stubs allowing a coding capacity of 9 bits and operating in a frequency range from 2 to 4GHz. The receiving and transmitting antennas of the tag are particularly designed to minimize the tag size as much as possible. The proposed tag presents a robust bit pattern with a compact and fully printable structure using FR4 substrate for a low-cost tag.

scholarly journals Frequency-Spectra-Based High Coding Capacity Chipless RFID Using an UWB-IR Approach

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2525
Author(s):  
Kawther Mekki ◽  
Omrane Necibi ◽  
Hugo Dinis ◽  
Paulo Mendes ◽  
Ali Gharsallah
Keyword(s):  
Radio Frequency Identification ◽  
Ultra Wideband ◽  
Frequency Spectra ◽  
Rfid Tag ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Main Components ◽  
The Time Domain ◽  
Antenna Mode ◽  
Structural Mode

A novel methodology is proposed to reliably predict the resonant characteristics of a multipatch backscatter-based radio frequency identification (RFID) chipless tag. An ultra-wideband impulsion radio (UWB-IR)-based reader interrogates the chipless tag with a UWB pulse, and analyzes the obtained backscatter in the time domain. The RFID system consists of a radar cross-section (RCS)-based chipless tag containing a square microstrip patch antenna array in which the chipless tag is interrogated with a UWB pulse by an UWB-IR-based reader. The main components of the backscattered signal, the structural mode, and the antenna mode were identified and their spectral quality was evaluated. The study revealed that the antenna-mode backscatter includes signal carrying information, while the structural mode backscatter does not include any tag information. The simulation findings were confirmed by experimental measurements obtained in an anechoic chamber environment using a 6-bit multipatch chipless RFID tag. Finally, the novel technique does not use calibration tags and can freely orient tags with respect to the reader.

scholarly journals A Novel L-Shape Ultra Wideband Chipless Radio-Frequency Identification Tag

2017 ◽  
Vol 2017 ◽  
pp. 1-7 ◽  
Author(s):  
Khaled Issa ◽  
Muhammad A. Ashraf ◽  
Mohammed R. AlShareef ◽  
Hatim Behairy ◽  
Saleh Alshebeili ◽  
...  
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Measurement Data ◽  
Ultra Wideband ◽  
Spectral Signature ◽  
Rfid Tag ◽  
High Data ◽  
Frequency Identification ◽  
Dual Polarized ◽  
5 Ghz

A novel compact dual-polarized-spectral-signature-based chipless radio-frequency identification (RFID) tag is presented. Specifically, an L-shape resonator-based structure is optimized to have different spectral signatures in both horizontal and vertical polarizations, in order to double the encoding capacity. Resonators’ slot width and the space between closely placed resonators are also optimized to enhance the mutual coupling, thereby helping in achieving high-data encoding density. The proposed RFID tag operates over 5 GHz to 10 GHz frequency band. As a proof of concept, three different 18-bit dual-polarized RFID tags are simulated, fabricated, and tested in an anechoic chamber environment. The measurement data show reasonable agreement with the simulation results, with respect to resonators’ frequency positions, null depth, and their bandwidth over the operational spectrum.

scholarly journals Plus Shaped Chipless RFID Tag

2021 ◽  
Vol 40 ◽  
pp. 01004
Author(s):  
Vinay Ganesh Bhagure ◽  
Somdotta Roy Choudhury
Keyword(s):  
Internet Of Things ◽  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Future Internet ◽  
Rfid Tags ◽  
Rfid Technology ◽  
Rfid Tag ◽  
Chipless Rfid ◽  
Frequency Identification ◽  
Radio Frequency Waves

Chip-less radio frequency identification (RFID) technology is capable for detecting, identification, and chasing for the future Internet of Things (IoT) systems and applications. The chipless RFID technology gives us the impression as a rising substitute of the traditional RFID tags and barcodes by encoding data from tags employing the radio frequency waves. The paper presents the design as well as simulation of chip-less Plus shaped RFID tags. The structure is composed of Rogers RT/Duroid 5880 by means of a substrate having the physical dimensions 40mm x 40mm over which eight resonators are placed. This tag is compact, and the resonators are closely placed. The tag is designed using Ansys Electronics Desktop.

Design and characterization of novel fabric-based multi-resonators for wearable chipless RFID applications

2021 ◽  
pp. 004051752198978
Author(s):  
Huating Tu ◽  
Yaya Zhang ◽  
Hong Hong ◽  
Jiyong Hu ◽  
Xin Ding
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Printed Circuit Boards ◽  
Signal Transmission ◽  
Circuit Boards ◽  
Cross Sectional ◽  
Rfid Tag ◽  
Response Characteristics ◽  
Chipless Rfid ◽  
Screen Printed

Nowadays, the chipless radio frequency identification (RFID) tag is attracting significant attention owing to its immense potential in tracking. However, most of the chipless tags are fabricated on hard printed circuit boards, and the wearable fabric-based chipless tag is still in the research stage. In this paper, a symmetrical 3rd L-shaped multi-resonator wearable chipless RFID tag is designed and screen-printed onto fabric. In order to investigate the influence of the non-uniform conductive layer on the signal transmission at high frequency, the surface and cross-sectional topographies of the printed conductive film are analyzed and the frequency response characteristics are simulated and measured. The obtained results show that the common fabric can be used as the substrate to screen print the L-shaped multi-resonators of the chipless RFID tag, and the quality of the screen printed line, especially a narrow line, significantly affects the radio frequency performance. For the screen-printed 3rd L-shaped stub resonators, the relative frequency shift compared with the simulation results are 0.99%, 0.88% and 2.26%, respectively. Generally, the surface morphology of fabric and screen-printed precision are critical in improving the performance of L-shaped multi-resonators.

Sign in / Sign up

Export Citation Format

Share Document