scholarly journals Performance Improvement of Servo Control System Driven by Novel PMSM-DTC Based On Fixed Sector Division Criterion

Energies ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 2154 ◽  
Author(s):  
Dazhi Wang ◽  
Tianqing Yuan ◽  
Xingyu Wang ◽  
Xinghua Wang ◽  
Yongliang Ni
Keyword(s):  
Control System ◽  
Performance Improvement ◽  
Error Compensation ◽  
Permanent Magnet Synchronous Motor ◽  
Direct Torque Control ◽  
Torque Control ◽  
Servo Control ◽  
Flux Linkage ◽  
Servo Control System ◽  
Stator Flux

In order to improve the performance of the servo control system driven by a permanent magnet synchronous motor (PMSM) under novel direct torque control (NDTC), which, utilizing composite active vectors, fixed sector division criterion, is proposed in this paper. The precondition of the accurate compensations of torque and flux errors is that the sector where the stator flux linkage is located can be determined accurately. Consequently, the adaptive sector division criterion is adopted in NDTC. However, the computation burden is inevitably increased with the using of the adaptive part. On the other hand, the main errors can be compensated through SV-DTC (DTC-utilizing single active vector), while another active vector applied in NDTC can only supply the auxiliary error compensation. The relationships of the two active vectors’ characteristics in NDTC are analyzed in this paper based on the active factor. Furthermore, the fixed sector division criterion is proposed for NDTC (FS-NDTC), which can classify the complexity of the control system. Additionally, the switching table for the selections of the two active vectors is designed. The effectiveness of the proposed FS-NDTC is verified through the experimental results on a 100-W PMSM drive system.

The Design and Simulation of AC Asynchronous Motor Direct Torque Control System

2015 ◽  
Vol 713-715 ◽  
pp. 814-819
Author(s):  
Li Ping Zhang ◽  
Xu Guang Xin ◽  
Wei Ya Wang ◽  
Hai Feng Wu
Keyword(s):  
Control System ◽  
Dynamic Performance ◽  
Asynchronous Motor ◽  
Direct Torque Control ◽  
Torque Control ◽  
Analysis Method ◽  
Flux Linkage ◽  
Control Precision ◽  
Stator Flux ◽  
The Stability

The direct torque control (DTC) system of the traditional asynchronous motor has many disadvantages, such as complex modeling and large amount of calculation, In order to improve the dynamic performance of the DTC system of the asynchronous motor, a direct torque control system is put forward. It uses space vector analysis method to calculate electromagnetic torque and stator flux linkage of asynchronous motor directly, follows the change of the stator flux linkage and torque, omits the complicated calculation, reduces the dependence on motor parameters. The simulation model of the DTC system of the asynchronous motor was established using SIMULINK software package. The feasibility of method is proved in theory, The results of simulation show that the modeling and simulation of the system has good static and dynamic performance, control precision of the system is higher, the stability is better.

High-Performance Speed Sensorless Direct Torque Control of PMSM

2011 ◽  
Vol 130-134 ◽  
pp. 2828-2831 ◽  
Author(s):  
Yan Ping Xu ◽  
Ke Guo ◽  
Yan Ru Zhong
Keyword(s):  
Kalman Filter ◽  
High Performance ◽  
Permanent Magnet Synchronous Motor ◽  
Direct Torque Control ◽  
Torque Control ◽  
Flux Linkage ◽  
Speed Sensorless ◽  
Load Torque ◽  
Simulation Results ◽  
Stator Flux

A high-performance speed sensorless direct torque control (DTC) system of permanent magnet synchronous motor (PMSM) is presented in this paper. The stator flux linkage, speed, rotor position and load torque of PMSM are observed using a fourth-order Extended Kalman Filter (EKF) and a second-order Kalman Filter (KF) and the observed load torque is used for feed-forward compensation of reference torque. Simulation results clearly demonstrate the performance of speed can be improved when load torque is changed and the validity of the proposed control strategy.

scholarly journals Direct Torque Control Of Permanent Magnet Synchronous Motor

2011 ◽  
pp. 27-30
Author(s):  
Anusha Mudili ◽  
P Devendra
Keyword(s):  
Permanent Magnet Synchronous Motor ◽  
Direct Torque Control ◽  
Current Control ◽  
Torque Control ◽  
Self Control ◽  
Control Mode ◽  
Flux Linkage ◽  
Matlab Program ◽  
Hysteresis Controller ◽  
Stator Flux

The DTC of PMSM is a kind of self control mode for its stator flux linkage and torque .It is very important that if stator flux linkage can be observed well and because the accuracy of the observer for stator flux linkage directly affects the performance of the DTC system of PMSM. In this paper ,for a torque drive with hysteresis controller in the current control loop will be implemented by writing a MATLAB program.

scholarly journals Performance Improvement for PMSM DTC System through Composite Active Vectors Modulation

Electronics ◽  
2018 ◽  
Vol 7 (10) ◽  
pp. 263 ◽  
Author(s):  
Tianqing Yuan ◽  
Dazhi Wang
Keyword(s):  
Performance Improvement ◽  
Permanent Magnet Synchronous Motor ◽  
Control Period ◽  
Direct Torque Control ◽  
Operating Conditions ◽  
Torque Control ◽  
The Novel ◽  
Flux Linkage ◽  
Voltage Vector ◽  
Linkage Error

In this paper, a novel direct torque control (DTC) scheme based on composite active vectors modulation (CVM) is proposed for permanent magnet synchronous motor (PMSM). The precondition of the accurate compensations of torque error and flux linkage error is that the errors can be compensated fully during the entire control period. Therefore, the compensational effects of torque error and flux linkage error in different operating conditions of the PMSM are analyzed firstly, and then, the operating conditions of the PMSM are divided into three cases according to the error compensational effects. To bring the novel composite active vectors modulation strategy smoothly, the effect factors are used to represent the error compensational effects provided by the applied active vectors. The error compensational effects supplied by single active vector or synthetic voltage vector are analyzed while the PMSM is operated in three different operating conditions. The effectiveness of the proposed CVM-DTC is verified through the experimental results on a 100-W PMSM drive system.

Study on speed sensorless system of permanent magnet synchronous motor based on improved direct torque control

2021 ◽  
pp. 014233122110629
Author(s):  
Xiaoxin Hou ◽  
Mingqian Wang ◽  
Guodong You ◽  
Jinming Pan ◽  
Xiating Xu ◽  
...  
Keyword(s):  
Control System ◽  
Permanent Magnet ◽  
Permanent Magnet Synchronous Motor ◽  
Direct Torque Control ◽  
Torque Ripple ◽  
Synchronous Motor ◽  
Torque Control ◽  
Switching Frequency ◽  
Speed Sensorless ◽  
Stator Resistance

The traditional direct torque control system of permanent magnet synchronous motor has many problems, such as large torque ripple and variable switching frequency. In order to improve the dynamic and static performance of the control system, a new torque control idea and speed sensorless control scheme are proposed in this paper. First, by deriving the equation of torque change rate, an improved torque controller is designed to replace the torque hysteresis controller of the traditional direct torque control. The improved direct torque control strategy can significantly reduce the torque ripple and keep the switching frequency constant. Then, based on the improved direct torque control and considering the sensitivity of the stator resistance to temperature change, a speed estimator based on the model reference adaptive method is designed. This method realizes the stator resistance on-line identification and further improves the control precision of the system. The performance of the traditional direct torque control and the improved direct torque control are compared by simulation and experiment under different operating conditions. The simulation and experimental results are presented to support the validity and effectiveness of the proposed method.

Sign in / Sign up

Export Citation Format

Share Document