scholarly journals Comparative Study of Piezoelectric Vortex-Induced Vibration-Based Energy Harvesters with Multi-Stability Characteristics

Energies ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 71 ◽  
Author(s):  
Rashid Naseer ◽  
Huliang Dai ◽  
Abdessattar Abdelkefi ◽  
Lin Wang
Keyword(s):  
Comparative Study ◽  
Performance Optimization ◽  
Load Resistance ◽  
Lumped Parameter Model ◽  
Vortex Induced Vibration ◽  
Energy Harvesters ◽  
Softening Behavior ◽  
Piezoelectric Energy ◽  
Synchronization Region ◽  
Spacing Distance

This work reports a comparative study on piezoelectric energy harvesting from vortex-induced vibration (VIV) with multi-stability characteristics by introducing the nonlinear magnetic forces. A lumped-parameter model for the piezoelectric cantilever-cylinder structure is considered for the sake of qualitative investigation. Firstly, the buckling displacement of harvester in monostable and bistable configurations is evaluated by virtue of a static analysis. Then, the coupled frequency and damping of the harvester varying with the electrical load resistance are determined for different values of the spacing distance between magnets. Subsequently, the dynamic behaviors and generated voltage of the harvester in two configurations are elaborately investigated, showing that varying the spacing distance is followed by a shift of lock-in region which is significant for performance optimization according to ambient wind conditions. In addition, the results show the harvester in monostable configuration displays a hardening behavior while a softening behavior takes place in bistable configuration, both of the harvester in two configurations can widen the synchronization region.

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

Geometric and Material Optimization of Vortex-Induced Vibration Micro Energy Harvesters for Localized Wind Environments

2012 ◽  
Author(s):  
Jesse J. French ◽  
Colton T. Sheets
Keyword(s):  
Energy Harvesting ◽  
Power Output ◽  
Fluid Velocity ◽  
Frequency Variation ◽  
Vortex Induced Vibration ◽  
Energy Harvesters ◽  
Wind Speeds ◽  
Material Optimization ◽  
Piezoelectric Energy ◽  
Wind Velocities

Wind energy capture in today’s environment is often focused on producing large amounts of power through massive turbines operating at high wind speeds. The device presented by the authors performs on the extreme opposite scale of these large wind turbines. Utilizing vortex induced vibration combined with developed and demonstrated piezoelectric energy harvesting techniques, the device produces power consistent with peer technologies in the rapidly growing field of micro-energy harvesting. Vortex-induced vibrations in the Karman vortex street are the catalyst for energy production of the device. To optimize power output, resonant frequency of the harvester is matched to vortex shedding frequency at a given wind speed, producing a lock-on effect that results in the greatest amplitude of oscillation. The frequency of oscillation is varied by altering the effective spring constant of the device, thereby allowing for “tuning” of the device to specific wind environments. While localized wind conditions are never able to be predicted with absolute certainty, patterns can be established through thorough data collection. Sampling of local wind conditions led to the design and testing of harvesters operating within a range of wind velocities between approximately 4 mph and 25 mph. For the extremities of this range, devices were constructed with resonant frequencies of approximately 17 and 163 Hz. Frequency variation was achieved through altering the material composition and geometry of the energy harvester. Experimentation was performed on harvesters to determine power output at optimized fluid velocity, as well as above and below. Analysis was also conducted on shedding characteristics of the device over the tested range of wind velocities. Computational modeling of the device is performed and compared to experimentally produced data.

Comparative study between the pillar- and bulk-type multilayer structures for piezoelectric energy harvesters (Phys. Status Solidi A 8∕2014)

2014 ◽  
Vol 211 (8) ◽  
pp. n/a-n/a
Author(s):  
Dong-Jin Shin ◽  
Woo-Seok Kang ◽  
Jung-Hyuk Koh ◽  
Kyung-Ho Cho ◽  
Chang-Eui Seo ◽  
...  
Keyword(s):  
Comparative Study ◽  
Multilayer Structures ◽  
Energy Harvesters ◽  
Piezoelectric Energy

Comparative study between the pillar- and bulk-type multilayer structures for piezoelectric energy harvesters

2014 ◽  
Vol 211 (8) ◽  
pp. 1812-1817 ◽  
Author(s):  
Dong-Jin Shin ◽  
Woo-Seok Kang ◽  
Jung-Hyuk Koh ◽  
Kyung-Ho Cho ◽  
Chang-Eui Seo ◽  
...  
Keyword(s):  
Comparative Study ◽  
Multilayer Structures ◽  
Energy Harvesters ◽  
Piezoelectric Energy

scholarly journals Improved Multilayered (Bi,Sc)O3-(Pb,Ti)O3 Piezoelectric Energy Harvesters Based on Impedance Matching Technique

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 1958 ◽  
Author(s):  
Bo Su Kim ◽  
Jae-Hoon Ji ◽  
Hong-Tae Kim ◽  
Sung-Jin Kim ◽  
Jung-Hyuk Koh
Keyword(s):  
Energy Harvesting ◽  
Impedance Matching ◽  
Load Resistance ◽  
Mechanical Force ◽  
Output Energy ◽  
Maximum Output ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Matching Technique ◽  
Matching Techniques

As a piezoelectric material, (Bi,Sc)O3-(Pb,Ti)O3 ceramics have been tested and analyzed for sensors and energy harvester applications owing to their relatively high Curie temperature and high piezoelectric coefficient. In this work, we prepared optimized (Bi,Sc)O3-(Pb,Ti)O3 piezoelectric materials through the conventional ceramic process. To increase the output energy, a multilayered structure was proposed and designed, and to obtain the maximum output energy, impedance matching techniques were considered and tested. By varying and measuring the energy harvesting system, we confirmed that the output energies were optimized by varying the load resistance. As the load resistance increased, the output voltage became saturated. Then, we calculated the optimized output power using the electric energy formula. Consequently, we identified the highest output energy of 5.93 µW/cm2 at 3 MΩ for the quadruple-layer harvester and load resistor using the impedance matching system. We characterized and improved the electrical properties of the piezoelectric energy harvesters by introducing impedance matching and performing the modeling of the energy harvesting component. Modeling was conducted for the piezoelectric generator component by introducing the mechanical force dependent voltage sources and load resistors and piezoelectric capacitor connected in parallel. Moreover, the generated output voltages were simulated by introducing an impedance matching technique. This work is designed to explain the modeling of piezoelectric energy harvesters. In this model, the relationship between applied mechanical force and output energy was discussed by employing experimental results and simulation.

Parametric analysis of multilayered unimorph piezoelectric vibration energy harvesters

2015 ◽  
Vol 23 (15) ◽  
pp. 2538-2553 ◽  
Author(s):  
Ahmed Jemai ◽  
Fehmi Najar ◽  
Moez Chafra
Keyword(s):  
Energy Harvester ◽  
Electrical Power ◽  
Closed Form Solution ◽  
Beam Theory ◽  
Load Resistance ◽  
Form Solution ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
Piezoelectric Layers

The use of a multilayer piezoelectric cantilever beam for vibration-based energy harvesting applications has been investigated as an effective technique to increase the harvested electrical power. It has been shown that the multilayered energy harvester performance is very sensitive to the number of layers and their electrical connection due to impedance variations. The objective of this work is to suggest a comprehensive mathematical model of multilayered unimorph piezoelectric energy harvester allowing analytical solution for the harvested voltage and electrical power. The model is used to deeply investigate the influence of different parameters on the harvested power. A distributed-parameter model of the harvester using the Euler–Bernoulli beam theory and Hamilton's principle is derived. Gauss's law is used to derive the electrical equations for parallel and series connections. A closed-form solution is proposed based on the Galerkin procedure and the obtained results are validated with a finite element 3D model. A parametric study is performed to ascertain the influence of the load resistance, the thickness ratio, the number of piezoelectric layers on the tip displacement and the electrical harvested power. It is shown that this model can be easily used to adjust the geometrical and electrical parameters of the energy harvester in order to improve the system's performances. In addition, it is proven that if one of the system's parameter is not correctly tuned, the harvested power can decrease by several orders of magnitude.

A High Precision Lumped Parameter Model for Piezoelectric Energy Harvesters

2017 ◽  
Vol 17 (24) ◽  
pp. 8350-8355 ◽  
Author(s):  
Srimanta Baishya ◽  
Debarun Borthakur ◽  
Richik Kashyap ◽  
Amitabh Chatterjee
Keyword(s):  
High Precision ◽  
Lumped Parameter Model ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Lumped Parameter

scholarly journals Modeling and Analysis of Upright Piezoelectric Energy Harvester under Aerodynamic Vortex-induced Vibration

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 667 ◽  
Author(s):  
Jinda Jia ◽  
Xiaobiao Shan ◽  
Deepesh Upadrashta ◽  
Tao Xie ◽  
Yaowen Yang ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Beam Theory ◽  
Longitudinal Direction ◽  
Load Resistance ◽  
Vortex Induced Vibration ◽  
Modeling And Analysis ◽  
Coupled Equations ◽  
Output Performance ◽  
Piezoelectric Energy ◽  
Tip Mass

This paper presents an upright piezoelectric energy harvester (UPEH) with cylinder extension along its longitudinal direction. The UPEH can generate energy from low-speed wind by bending deformation produced by vortex-induced vibrations (VIVs). The UPEH has the advantages of less working space and ease of setting up an array over conventional vortex-induced vibration harvesters. The nonlinear distributed modeling method is established based on Euler–Bernoulli beam theory and aerodynamic vortex-induced force of the cylinder is obtained by the van der Pol wake oscillator theory. The fluid–solid–electricity governing coupled equations are derived using Lagrange’s equation and solved through Galerkin discretization. The effect of cylinder gravity on the dynamic characteristics of the UPEH is also considered using the energy method. The influences of substrate dimension, piezoelectric dimension, the mass of cylinder extension, and electrical load resistance on the output performance of harvester are studied using the theoretical model. Experiments were carried out and the results were in good agreement with the numerical results. The results showed that a UPEH configuration achieves the maximum power of 635.04 μW at optimum resistance of 250 kΩ when tested at a wind speed of 4.20 m/s. The theoretical results show that the UPEH can get better energy harvesting output performance with a lighter tip mass of cylinder, and thicker and shorter substrate in its synchronization working region. This work will provide the theoretical guidance for studying the array of multiple upright energy harvesters.

Analysis and Characterization of Piezoelectric Energy Harvesting From Galloping and Base Excitations With Complex Electrical Circuitry

2016 ◽  
Author(s):  
Hichem Abdelmoula ◽  
Abdessattar Abdelkefi
Keyword(s):  
Excitation Frequency ◽  
Beam Theory ◽  
Load Resistance ◽  
Electrical Circuit ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
And Performance ◽  
Electrical Components ◽  
Euler Bernoulli Beam ◽  
Quenching Phenomenon

The characteristics and performance of piezoelectric energy harvesters concurrently subjected to galloping and base excitations when using a complex electrical circuit are studied. The considered energy harvester is composed of a bilayered cantilever beam with a square cylindrical structure at its tip. Euler-Bernoulli beam theory, nonlinear quasi-steady hypothesis, and Galerkin method are used to develop a reduced order model of this system. The electrical circuitry of the harvester consists of a load resistance, a capacitance, and an inductance. The impacts of the electrical components of the harvester’s circuitry, the wind speed, and the base excitation frequency and acceleration on the broadband characteristics of the harvester, quenching phenomenon, and appearance of new nonlinear behaviors are deeply investigated and discussed. When both coupled frequencies of electrical and mechanical types exists and are far from each other, it is shown that the quenching phenomenon is only related to the coupled frequency of mechanical type. Unlike the existence of the quenching phenomenon, the results show that the beating phenomenon takes place for different excitation frequencies when they are close to the coupled frequencies of electrical and mechanical types.

Sign in / Sign up

Export Citation Format

Share Document