scholarly journals Contamination of Brush Seals by Oil and Salt and Its Impact on Rubbing and Hysteresis Behaviour

2019 ◽  
Vol 4 (4) ◽  
pp. 40
Author(s):  
Manuel Hildebrandt ◽  
Corina Schwitzke ◽  
Hans-Jörg Bauer
Keyword(s):  
Heat Fluxes ◽  
Total Power ◽  
Steam Turbines ◽  
Power Losses ◽  
Test Rig ◽  
Degree Of Contamination ◽  
Brush Seal ◽  
Steady State Operation ◽  
Brush Seals ◽  
Hysteresis Behaviour

The literature already contains some experimental, analytical and numerical investigations on the rubbing and hysteresis behaviour of brush seals. What the investigations have in common is that they were carried out with new and uncontaminated seals, or that such a condition was assumed. The influence of contamination has not been explicitly investigated yet. Particularly in stationary gas and steam turbines, foreign substances can accumulate on and in the bristle package during steady-state operation. In the case of a rubbing event with a contaminated brush seal, e.g., during shutdown of the machine, the process is not expected to be comparable to that assumed in the presence of a new, uncontaminated seal. The present paper is dedicated to the question of the influence of contamination on the total frictional power loss generated during rubbing and the distribution of heat fluxes in friction contact. For this purpose, rub tests with two seals were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) in new conditions. Subsequently, the sealing packages were contaminated with oil or a salt mixture. After the treatment, the rub tests were repeated and compared with the previous tests. In addition, stiffness measurements were used to assess the degree of contamination. A strong influence on the rubbing behaviour by the contamination was detected. Contamination causes the flexibility of the bristle package to be greatly reduced. As a result, especially at the beginning of the first measurements, the total power losses and rotor heat inputs are strongly increased. This flexibility is partly regained in the course of the measurements. As expected, contamination also influences the hysteresis behaviour of the seal. A highly increased leakage rate after rubbing could be observed, because the bristles remained close to their deflected positions. In the case of the salted seal, however, an improvement in the leakage performance could be observed after several repeat tests.

Design Parameters of Brush Seals and Their Impact on Seal Performance

2012 ◽  
Author(s):  
H. Schwarz ◽  
J. Friedrichs ◽  
J. Flegler
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Large Scale ◽  
Design Parameters ◽  
Test Rig ◽  
Pressure Drops ◽  
Seal Design ◽  
Brush Seal ◽  
Extreme Load ◽  
Brush Seals

Brush seals, which were originally designed for gas turbine applications, have been successfully applied to large-scale steam turbines within the past decade. From gas turbine applications, the fundamental behavior and designing levers are known. However, the application of brush seals to a steam turbine is still a challenge. This challenge is mainly due to the extreme load on the brush seal while operating under steam. Furthermore, it is difficult to test brush seals under realistic conditions, i.e. under live steam conditions with high pressure drops. Due to these insufficiencies, 2 test rigs were developed at the University of Technology Braunschweig, Germany. The first test rig is operated under pressurized air and allows testing specific brush seal characteristics concerning their general behavior. The knowledge gained from these tests can be validated in the second test rig, which is operated under steam at pressure drops of 45 bar and temperatures up to 450 °C. Using both the air test rig and the steam test rig helps keep the testing effort comparably small. Design variants can be pre-tested with air, and promising brush seal designs can consequently be tested in the steam seal test rig. The paper focuses on a clamped brush seal design which, amongst others, is used in steam turbine blade paths and shaft seals of current Siemens turbines. The consequences of the brush assembly on the brush appearance and brush performance are shown. The clamped brush seal design reveals several particularities compared to welded brushes. It could be shown that the clamped bristle pack tends to gape when clamping forces rise. Gapping results in an axially expanding bristle pack, where the bristle density per unit area and the leakage flow vary. Furthermore, the brush elements are usually assembled with an axial lay angle, i.e. the bristles are reclined against the backing plate. Hence, the axial lay angle is also part of the investigation.

Operational Performance and Locally Resolved Outflow of Brush Seals

2019 ◽  
Author(s):  
Fabian Schur ◽  
Jens Friedrichs
Keyword(s):  
Operational Performance ◽  
Design Parameters ◽  
Steam Turbines ◽  
Test Rig ◽  
Rotating Shaft ◽  
Experimental Conditions ◽  
Widespread Application ◽  
Backing Plate ◽  
Brush Seals ◽  
The Impact

Abstract As a result of the superior leakage efficiency of brush seals compared to conventional labyrinth seals, compliant contacting filament seals are used to increase the efficiency of jet engines as well as stationary gas and steam turbines. The widespread application of brush seals at different and varying pressure differences combined with variable contacting velocities at the rotor surface requires a profound understanding of the influences of different design parameters on the operational leakage performance. In order to systematically investigate the impact of different design parameters on sealing performance, a new cold air test rig was developed. The new test rig with rotating shaft enables hot-wire anemometry measurements downstream of the seals. These measurements provide insight into the locally resolved flow structure in addition to the integral leakage measurements. For the investigations, one welded and five different clamped brush seals at rotational speeds up to 3000rpm and pressure differences across the seals up to 500kPa are considered. Therefore, the influence of two different designs on the flow through the bristles is presented. For the clamped brush seals, variations of the front and backing plate are investigated. Additionally, the effects of bristle diameter and three different axial inclinations of the bristle pack on the sealing efficiency are shown. Furthermore, initial wear development during the first 30 to 60 hours of brush seal operation at varying experimental conditions is presented and linked to the design parameters. Consequently, the effects of major design aspects on the operational performance of brush seals are examined and presented.

An Experimental and Theoretical Study of Brush Seal and Shaft Thermal Interaction

2003 ◽  
Author(s):  
Andrew K. Owen ◽  
Terry V. Jones ◽  
S. M. Guo ◽  
Simon Hogg
Keyword(s):  
Theoretical Analysis ◽  
Test Facility ◽  
Thermal Interaction ◽  
Steam Turbines ◽  
Element Analysis ◽  
Oxford University ◽  
Brush Seal ◽  
Aerodynamic Parameters ◽  
Brush Seals ◽  
Seal Shaft

This paper presents a detailed experimental study and theoretical analysis of the thermal interactions of brush seal, shaft and airflow. The tests were performed in the Oxford University Brush Seal Test Facility. The facility, which was originally designed for the brush seal aerodynamic study, has been enhanced for thermal measurements. A variety of brush seals, typically applicable to aero and power generation gas and steam turbines, have been tested. The thermal interaction caused by changes in rotor and housing alignment was also studied. In the tests, in addition to the conventional aerodynamic parameters, such as the pressure, mass flow and torque, the temperatures of the rotor were measured and heat generated in the bristle/rotor contact were deduced using the finite element analysis. A theoretical analysis of the system was developed which predicts the heat transfer to the airflow from the bristle pack. This analysis is used to give a correlation to predict heat input to the rotor. The study provides valuable design information for the use of brush seals.

Design and Validation of a New Test Rig for Brush Seal Testing Under Engine Relevant Conditions

2011 ◽  
Author(s):  
D. Pfefferle ◽  
K. Dullenkopf ◽  
H.-J. Bauer
Keyword(s):  
High Surface ◽  
Test Rig ◽  
Friction Forces ◽  
Brush Seal ◽  
Main Emphasis ◽  
Rotor Surface ◽  
Brush Seals ◽  
Gap Height ◽  
Radial Gap ◽  
Gap Width

Brush seals play an increasing role in turbomachinery due to their improved behavior towards leakage and their capability to compensate for gap variations caused by thermal expansion and rotor excursions. The flexible bristles of brush seals are able to endure short-term reductions in gap width without severe damage. Consequently the necessary gap between the rotor and brush seal can virtually be reduced to zero, leading to a considerable reduction in air leakage of up to 80 percent. However the reduced gap height increases the probability of rubbing between the bristle package and the rotor surface. The friction forces generated can cause an unwanted heat load on the rotor, bristles and leakage air. In addition, the surfaces involved are exposed to abrasion effects. Especially in the thin and lightweight rotor structures of aircraft engines, the additional heat impact can lead to a problematic level of material stress. To study these effects and to give reliable quantitative design rules, a versatile test rig for brush seals was designed and built. The simulation of seal behavior under relevant engine conditions is the main emphasis of this rig, including high pressure drop, leakage flow and high surface speed. The key feature is the possibility to vary the axis symmetric radial gap width during the test rig operation by up to a 0.5 mm overlap. The so caused rubbing induces a transient rotor temperature rise which is measured via a set of 12 thermocouples embedded in the rotor. These temperature readings can be used to calculate the brush seal heat impact on the rotor structure. Preliminary results with moderate differential pressure and rotor speed proved the functionality of the test rig and confirmed the global approach of the project.

An Investigation of Flow, Mechanical and Thermal Performance of Conventional and Pressure-Balanced Brush Seals

2012 ◽  
Author(s):  
Michael J. Pekris ◽  
Gervas Franceschini ◽  
David R. H. Gillespie
Keyword(s):  
Test Rig ◽  
Blow Down ◽  
Active Pressure ◽  
University Of Oxford ◽  
Seal Design ◽  
Passive Pressure ◽  
Brush Seal ◽  
Fuel Consumption Benefit ◽  
Brush Seals ◽  
Secondary Air

Compliant contacting filament seals such as brush seals are well known to give improved leakage performance and hence specific fuel consumption benefit compared to labyrinth seals. The design of the brush seal must be robust across a range of operating pressures, rotor speeds and radial build-offset tolerances. Importantly the wear characteristics of the seal must be well understood to allow a secondary air system suitable for operation over the entire engine life to be designed. A test rig at the University of Oxford is described which was developed for the testing of brush seals at engine-representative speeds, pressures and seal housing eccentricities. The test rig allows the leakage, torque and temperature rise in the rotor to be characterized as functions of the differential pressure(s) across the seal and the speed of rotation. Tests were run on two different geometries of bristle-pack with conventional, passive and active pressure-balanced backing ring configurations. Comparison of the experimental results indicates that the hysteresis inherent in conventional brush seal design could compromise performance (due to increased leakage) or life (due to exacerbated wear) as a result of reduced compliance. The inclusion of active pressure-balanced backing rings in the seal designs are shown to alleviate the problem of bristle-backing ring friction, but this is associated with increased blow-down forces which could result in a significant seal-life penalty. The best performing seal was concluded to be the passive pressure-balanced configuration, which achieves the best compromise between leakage and seal torque. Seals incorporating passive pressure-balanced backing rings are also shown to have improved heat transfer performance in comparison to other designs.

Aerodynamic Flutter of Turbine Brush Seals

2017 ◽  
Author(s):  
Samuel J. Borgueta ◽  
Nicholas R. Bach ◽  
Jared J. Correia ◽  
Brendan G. J. Egan ◽  
Joshua S. Horton ◽  
...  
Keyword(s):  
High Pressure ◽  
Steam Turbine ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Steam Turbines ◽  
High Pressure Steam ◽  
Modes Of Failure ◽  
Brush Seal ◽  
Pressure Steam ◽  
Brush Seals

With global energy demands continually growing and environmental impacts a major concern in power production, maximizing the efficiencies of power plants is of top priority. EthosEnergy2 has sponsored a project at the University of Massachusetts Dartmouth to study and analyze the brush seals in steam turbines in pursuit of increasing steam turbine thermodynamic efficiency. Brush seals are incorporated circumferentially around the turbine blades in their housing. The brush seals provide a very minimal clearance height that compensates for start-up rotor deviation and minimizes high-pressure steam blow-by around the edges of the blades. Brush seals minimize the clearance height between the blades and housing, which allows the turbine to produce more work. However, overtime brush seals can be damaged, greatly reducing efficiency. The seals that are repeatedly showing excessive wear and damage, occur in the high-pressure sections of steam turbines with high Reynolds numbers. The bristle breakdown is attributed to high Reynolds numbers and aerodynamic flutter. The purpose of this research is to design a prototype and empirically model steam turbine conditions with air to map out the fluid-solid interaction, determine the modes of bristle failure, and ultimately reproduce and record bristle flutter. A pressure vessel and pressure system was designed to test linear strips of brush seals with air as the working fluid. The pressure vessel accommodates varying clearance heights to identify the correlation of clearance height and the effects on fluid flow. The system also incorporates a high-speed camera that can capture the phenomena of flutter, precisely identify the modes of failure, and record fluid-solid interaction and the interaction of the bristles with each other. Designing a prototype to empirically model this problem serves as a fundamental and critical step in understanding the fluid interaction with seals in high-pressure steam turbines and will identify brush seal modes of failure. The prototype’s ability to model steam turbine conditions and rapidly test various seal designs will facilitate better brush seal designs to be constructed and will ultimately increase the thermal efficiencies of steam turbines, aid in accommodating the increase in global energy demands, and reduce the detrimental environmental impacts of producing power. The system successfully produced and recorded brush-seal-bristle flutter while modeling high-pressure steam turbine conditions. Matching Reynolds and Euler numbers of the steam turbine stages provided the ability to scale the steam turbine to our prototype, with air as the working fluid. Brush seal breakdown was occurring in steam turbines at Reynolds numbers above 20,000. The prototype repeatedly produced brush seal flutter at Reynolds numbers above 25,000, validating the theory that brush seal breakdown is dependent predominantly on the Reynolds number.

Brush Seal Frictional Heat Generation: Test Rig Design and Validation Under Steam Environment

2016 ◽  
Author(s):  
M. Raben ◽  
J. Friedrichs ◽  
J. Flegler
Keyword(s):  
Steam Turbine ◽  
Heat Generation ◽  
Gas Turbines ◽  
Frictional Heat ◽  
Narrow Gap ◽  
Test Rig ◽  
Frictional Heat Generation ◽  
Brush Seal ◽  
Rotor Surface ◽  
Brush Seals

Sealing technology is a key feature to improve efficiency of steam turbines for both new power stations and modernization projects. One of the most powerful sealing alternatives for reducing parasitic leakages in the blade path of a turbine as well as in shaft sealing areas is the use of brush seals, which are also widely used in gas turbines and turbo compressors. The advantage of brush seals over other sealing concepts is based on the narrow gap that is formed between the brush seal bristle tips and the mating rotor surface together with its radial adaptivity. While the narrow gap between the bristle tips and the rotor leads to a strongly decreased flow through the seal compared with conventional turbomachinery seals, it is important to be aware of the tight gap that can be bridged by relative motion between the rotor and the brush seal, leading to a contact of the bristles and the rotor surface. Besides abrasive wear occurrence, the friction between the bristles and the rotor leads to heat generation which can be detrimental to turbine operation due to thermal effects, leading to rotor bending connected to increasing shaft vibrations. In order to investigate the frictional heat generation of brush seals, different investigation concepts have been introduced through the past years. To broaden the knowledge about frictional heat generation and to make it applicable for steam turbine applications, a new testing setup was designed for the steam test rig of the Institute of Jet Propulsion and Turbomachinery - TU Braunschweig, Germany, enabling temperature measurements in the rotor body under stationary and transient operation in steam by using rotor-integrated thermocouples. Within this paper, the development of the instrumented new rotor design and all relevant parts of the new testing setup is shown along with the testing ability by means of the validation of the test rig concept and the achieved measurement accuracy. First results prove that the new system can be used to investigate frictional heat generation of brush seals under conditions relevant for steam turbine shaft seals.

scholarly journals INVESTIGATION OF A NOVEL PRESSURE-ACTUATED BRUSH SEAL UNDER HOT STEAM CONDITIONS

2020 ◽  
Vol 4 ◽  
pp. 14-26
Author(s):  
Philip Reggentin ◽  
Jens Friedrichs ◽  
Johan Flegler ◽  
Ivan McBean
Keyword(s):  
Power Plants ◽  
The Novel ◽  
Basic Design ◽  
Test Rig ◽  
Brush Seal ◽  
Brush Seals ◽  
Increasing Demand ◽  
Improved Design ◽  
Flexible Operation ◽  
Novel Design

Due to the increasing demand towards flexible operation of conventional power plants also the seals of their turbines have to adapt to varying loads. Based on the basic design of a clamped brush seal, a novel seal with a pressure-actuated backplate is introduced which is capable of combining the advantages of low and high inclined brush seals while avoiding their undesired properties for flexible operation. During preliminary investigations on a test rig operated with compressed air and without rotation, the functionality of the improved design was demonstrated. It is shown that the leakage mass flow was lowered by up to 40% while undesired bristle oscillations were reduced by up to 90% at low pressure differences compared to conventional seal designs. After the adaption of the design for subsequent investigations under realistic conditions comparable to those in a steam turbine, further tests were conducted at TU Braunschweig´s hot steam test rig. Within these investigations the novel design showed improved properties regarding a high leakage performance and an advanced capability to avoid deterioration due to shaft excursions compared to brush seals with fixed backplate design.

Design Features and Performance Details of Brush Seals for Turbine Applications

2006 ◽  
Author(s):  
Matthias Neef ◽  
Erik Sulda ◽  
Norbert Su¨rken ◽  
Jan Walkenhorst
Keyword(s):  
Phenomenological Approach ◽  
Performance Degradation ◽  
Operating Conditions ◽  
Special Focus ◽  
Steam Turbines ◽  
Seal Design ◽  
Brush Seal ◽  
Brush Seals ◽  
And Performance

Adaptive and contacting seals such as brush seals have been successfully applied to turbomachinery for several years. In large steam turbine applications, however, various challenges still persist. Special focus is directed at the long-term performance and longevity of brushes on conventional spring-backed seal segments in steam turbines. This issue is particularly related to wear during startup conditions. This paper discusses the results of wear tests, derived from simulated transient turbine behavior, where the resultant seal leakage under steady state conditions is monitored. It is shown that the brush seal is significantly capable of adapting to varying operating conditions, but exhibits a degree of performance degradation during the initial startups. Together with previously reported mid-term wear data and an experience based long-term phenomenological approach a general model for brush seal performance degradation is developed. This model can be used for performance prediction and exerts influence on brush seal design.

Brush Seal Frictional Heat Generation—Test Rig Design and Validation Under Steam Environment

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Markus Raben ◽  
Jens Friedrichs ◽  
Johan Flegler
Keyword(s):  
Steam Turbine ◽  
Heat Generation ◽  
Gas Turbines ◽  
Frictional Heat ◽  
Narrow Gap ◽  
Test Rig ◽  
Frictional Heat Generation ◽  
Brush Seal ◽  
Rotor Surface ◽  
Brush Seals

Sealing technology is a key feature to improve efficiency of steam turbines for both new power stations and modernization projects. One of the most powerful sealing alternatives for reducing parasitic leakages in the blade path of a turbine as well as in shaft sealing areas is the use of brush seals, which are also widely used in gas turbines and turbo compressors. The advantage of brush seals over other sealing concepts is based on the narrow gap that is formed between the brush seal bristle tips and the mating rotor surface together with its radial adaptivity. While the narrow gap between the bristle tips and the rotor leads to a strongly decreased flow through the seal compared with conventional turbomachinery seals, it is important to be aware of the tight gap that can be bridged by relative motion between the rotor and the brush seal, leading to a contact of the bristles and the rotor surface. Besides abrasive wear occurrence, the friction between the bristles and the rotor leads to heat generation which can be detrimental to turbine operation due to thermal effects, leading to rotor bending connected to increasing shaft vibrations. In order to investigate the frictional heat generation of brush seals, different investigation concepts have been introduced through the past years. To broaden the knowledge about frictional heat generation and to make it applicable for steam turbine applications, a new testing setup was designed for the steam test rig of the Institute of Jet Propulsion and Turbomachinery—TU Braunschweig, Germany, enabling temperature measurements in the rotor body under stationary and transient operation in steam by using rotor-integrated thermocouples. Within this paper, the development of the instrumented new rotor design and all relevant parts of the new testing setup is shown along with the testing ability by means of the validation of the test rig concept and the achieved measurement accuracy. First results prove that the new system can be used to investigate frictional heat generation of brush seals under conditions relevant for steam turbine shaft seals.

Sign in / Sign up

Export Citation Format

Share Document