Operational Performance and Locally Resolved Outflow of Brush Seals

2019 ◽  
Author(s):  
Fabian Schur ◽  
Jens Friedrichs
Keyword(s):  
Operational Performance ◽  
Design Parameters ◽  
Steam Turbines ◽  
Test Rig ◽  
Rotating Shaft ◽  
Experimental Conditions ◽  
Widespread Application ◽  
Backing Plate ◽  
Brush Seals ◽  
The Impact

Abstract As a result of the superior leakage efficiency of brush seals compared to conventional labyrinth seals, compliant contacting filament seals are used to increase the efficiency of jet engines as well as stationary gas and steam turbines. The widespread application of brush seals at different and varying pressure differences combined with variable contacting velocities at the rotor surface requires a profound understanding of the influences of different design parameters on the operational leakage performance. In order to systematically investigate the impact of different design parameters on sealing performance, a new cold air test rig was developed. The new test rig with rotating shaft enables hot-wire anemometry measurements downstream of the seals. These measurements provide insight into the locally resolved flow structure in addition to the integral leakage measurements. For the investigations, one welded and five different clamped brush seals at rotational speeds up to 3000rpm and pressure differences across the seals up to 500kPa are considered. Therefore, the influence of two different designs on the flow through the bristles is presented. For the clamped brush seals, variations of the front and backing plate are investigated. Additionally, the effects of bristle diameter and three different axial inclinations of the bristle pack on the sealing efficiency are shown. Furthermore, initial wear development during the first 30 to 60 hours of brush seal operation at varying experimental conditions is presented and linked to the design parameters. Consequently, the effects of major design aspects on the operational performance of brush seals are examined and presented.

Pressure Distributions Below Brush Seals at Varying Operating Conditions

2018 ◽  
Author(s):  
Fabian Schur ◽  
Jens Friedrichs ◽  
Johan Flegler ◽  
Christos Georgakis ◽  
Thomas Polklas
Keyword(s):  
Radial Pressure ◽  
Operating Conditions ◽  
Optical Measurements ◽  
Design Parameters ◽  
Test Rig ◽  
Axial Pressure ◽  
Backing Plate ◽  
Pressure Distributions ◽  
Flow Through ◽  
Brush Seals

The influences of different manufacturing methods and design parameters of brush seals and their complex interactions with the flow through the bristle pack complicate the modeling of the flow through brush seals. While radial pressure distributions along the backing plate and the leakage behaviour of various brush seal designs are published, experimental data on axial pressure distributions on the surface of the shaft is insufficient. In order to gain a better understanding of the phenomena associated with the flow through brush seals, the axial pressure distributions in the sealing gap below six different brush seals are measured on a cold air test rig at rotational speeds up to 3000rpm and pressure differences across the seals up to 500kPa with an axial resolution of 0.2mm. By investigating a welded and five different clamped brush seals, the influence of two different designs on the flow through the bristles is shown. For the clamped brush seals the design of the front and backing plate is varied. Moreover, the effects of bristle diameter and three different axial inclinations of the bristle pack on the axial pressure distribution are presented. Therefore, the effects of the major design aspects on axial pressure distributions at the interface between brush seals and rotor are examined and the results are supported by optical measurements taken on the rotating and a stationary test rig.

Design Parameters of Brush Seals and Their Impact on Seal Performance

2012 ◽  
Author(s):  
H. Schwarz ◽  
J. Friedrichs ◽  
J. Flegler
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Large Scale ◽  
Design Parameters ◽  
Test Rig ◽  
Pressure Drops ◽  
Seal Design ◽  
Brush Seal ◽  
Extreme Load ◽  
Brush Seals

Brush seals, which were originally designed for gas turbine applications, have been successfully applied to large-scale steam turbines within the past decade. From gas turbine applications, the fundamental behavior and designing levers are known. However, the application of brush seals to a steam turbine is still a challenge. This challenge is mainly due to the extreme load on the brush seal while operating under steam. Furthermore, it is difficult to test brush seals under realistic conditions, i.e. under live steam conditions with high pressure drops. Due to these insufficiencies, 2 test rigs were developed at the University of Technology Braunschweig, Germany. The first test rig is operated under pressurized air and allows testing specific brush seal characteristics concerning their general behavior. The knowledge gained from these tests can be validated in the second test rig, which is operated under steam at pressure drops of 45 bar and temperatures up to 450 °C. Using both the air test rig and the steam test rig helps keep the testing effort comparably small. Design variants can be pre-tested with air, and promising brush seal designs can consequently be tested in the steam seal test rig. The paper focuses on a clamped brush seal design which, amongst others, is used in steam turbine blade paths and shaft seals of current Siemens turbines. The consequences of the brush assembly on the brush appearance and brush performance are shown. The clamped brush seal design reveals several particularities compared to welded brushes. It could be shown that the clamped bristle pack tends to gape when clamping forces rise. Gapping results in an axially expanding bristle pack, where the bristle density per unit area and the leakage flow vary. Furthermore, the brush elements are usually assembled with an axial lay angle, i.e. the bristles are reclined against the backing plate. Hence, the axial lay angle is also part of the investigation.

scholarly journals Multiparameter Analysis for Efficiency Improvement of Single-Phase Capacitor Motor

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Vasilija Sarac ◽  
Tatjana Atanasova-Pacemska
Keyword(s):  
Parametric Analysis ◽  
Single Phase ◽  
Electricity Consumption ◽  
Design Parameters ◽  
Magnetic Flux Density ◽  
Operating Characteristics ◽  
Widespread Application ◽  
Electrical Motors ◽  
Multiparameter Analysis ◽  
The Impact

Single-phase motors are known for their small power ratings and their usage in various household appliances. Although they are not large electricity consumers, their widespread application contributes to the overall electricity consumption. In addition, standard IEC 60034-30-1:214 defines the efficiency levels for single- and three-phase motors and stipulates the increased electrical efficiency for the electrical motors. Therefore, this paper sets the parametric analysis of permanently split capacitor motor with five different design parameters that have impact on the efficiency of the motor. As an output from the parametric analysis, two different optimized motor models are obtained with increased efficiency. The impact of each parameter on motor efficiency—as well as on the other operating characteristics, like starting torque, overloading capacity, rated current, starting current, total losses, and power factor—is analyzed and adequate conclusions are derived. The obtained motor models are verified with Finite Element Method (FEM) for magnetic flux density distribution.

Computational Fluid Dynamics Investigation of Brush Seal Leakage Performance Depending on Geometric Dimensions and Operating Conditions

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Yahya Dogu ◽  
Ahmet S. Bahar ◽  
Mustafa C. Sertçakan ◽  
Altuğ Pişkin ◽  
Ercan Arıcan ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Ratio ◽  
Plate Thickness ◽  
Operating Conditions ◽  
Design Parameters ◽  
Backing Plate ◽  
Brush Seal ◽  
Front Plate ◽  
Brush Seals

Brush seals require custom design and tailoring due to their behavior driven by flow dynamic, which has many interacting design parameters, as well as their location in challenging regions of turbomachinery. Therefore, brush seal technology has not reached a conventional level across the board standard. However, brush seal geometry generally has a somewhat consistent form. Since this consistent form does exist, knowledge of the leakage performance of brush seals depending on specific geometric dimensions and operating conditions is critical and predictable information in the design phase. However, even though there are common facts for some geometric dimensions available to designers, open literature has inadequate quantified information about the effect of brush seal geometric dimensions on leakage. This paper presents a detailed computational fluid dynamics (CFD) investigation quantifying the leakage values for some geometric variables of common brush seal forms functioning in some operating conditions. Analyzed parameters are grouped as follows: axial dimensions, radial dimensions, and operating conditions. The axial dimensions and their ranges are front plate thickness (z1 = 0.040–0.150 in.), distance between front plate and bristle pack (z2 = 0.010–0.050 in.), bristle pack thickness (z3 = 0.020–0.100 in.), and backing plate thickness (z4 = 0.040–0.150 in.). The radial dimensions are backing plate fence height (r1 = 0.020–0.100 in.), front plate fence height (r2 = 0.060–0.400 in.), and bristle free height (r3 = 0.300–0.500 in.). The operating conditions are chosen as clearance (r0 = 0.000–0.020 in.), pressure ratio (Rp = 1.5–3.5), and rotor speed (n = 0–40 krpm). CFD analysis was carried out by employing compressible turbulent flow in 2D axisymmetric coordinate system. The bristle pack was treated as a porous medium for which flow resistance coefficients were calibrated by using literature based test data. Selected dimensional and operational parameters for a common brush seal form were investigated, and their effects on leakage performance were quantified. CFD results show that, in terms of leakage, the dominant geometric dimensions were found to be the bristle pack thickness and the backing plate fence height. It is also clear that physical clearance dominates leakage performance, when compared to the effects of other geometric dimensions. The effects of other parameters on brush seal leakage were also analyzed in a comparative manner.

Axial Inclination of the Bristle Pack, a New Design Parameter of Brush Seals for Improved Operational Behavior in Steam Turbines

2014 ◽  
Author(s):  
H. Schwarz ◽  
J. Friedrichs ◽  
J. Flegler
Keyword(s):  
Design Parameter ◽  
Rotational Velocity ◽  
Operating Conditions ◽  
Design Parameters ◽  
Leakage Flow ◽  
Rotating Shaft ◽  
Blow Down ◽  
Seal Design ◽  
Back Plate ◽  
Brush Seals

Within this paper, the axial inclination of the bristle pack as a new design parameter for brush seals for use in a steam turbine and other rotating equipment is discussed. It is widely known that the behavior of brush seals can be influenced by important main design parameters of the bristle pack such as, but not limited to, the bristle thickness, the lay angle or the bristle length. Furthermore, the variation of the front and back plate results in different seal characteristics [1]. Each one of these parameters also has an influence on bristle damping, the blow down capability and thus the leakage flow. In addition, under changing and transient operating conditions, the radial adaptivity, which is essential for accommodating shaft deflection, is also a very important property. For a comprehensive seal design, the wear characteristic and deterioration effects have to be considered beside the above mentioned properties. At the Technical University of Braunschweig, brush seals are experimentally investigated with above focus on different test rigs. These rigs allow a detailed sealing performance investigation including live bristle pack observations and blow down measurement using cold air as well as brush seal investigations using live steam conditions up to 50bars and 450°C and a rotating shaft with representative rotational velocity. The paper shows and discusses experimental results of different axial inclinations of the bristle pack, while testing with constant front and back plate designs. The influences on the blow down, the axial behavior of the bristle pack, the leakage flow and the bristle pack stiffness are shown. The new effect of a rotating blow down type of bristle oscillation is also shown and discussed and finally a classification of the seal behavior depending of the different axial inclination is given.

CAE Based Brush Seal Characterization for Stiffness and Stress Levels

2015 ◽  
Author(s):  
E. Tolga Duran ◽  
Mahmut F. Aksit ◽  
Murat Ozmusul
Keyword(s):  
Operating Conditions ◽  
Design Parameters ◽  
Backing Plate ◽  
Seal Design ◽  
Brush Seal ◽  
Stress Levels ◽  
Brush Seals ◽  
Main Effects ◽  
State Pressure

Brush seals are complex structures having variety of design parameters, all of which affect the seal behavior under turbine operating conditions. The complicated nature of the seal pack and frictional interactions of rotor, backing plate and bristles result in nonlinear response of the brush seal to variances of design parameters. This study presents CAE based characterization of brush seals, which aims to investigate the main effects of several brush seal design parameters on brush seal stiffness and stress levels. Characterization work of this study includes free-state rotor rub (unpressurized seal), steady state (pressure load without rotor interference) and pressurized-rotor interference conditions.

Static Testing of Compliant Plate Seals

2012 ◽  
Author(s):  
Hrishikesh V. Deo ◽  
Deepak Trivedi
Keyword(s):  
Gas Turbines ◽  
High Speed ◽  
Pressure Ratio ◽  
Differential Pressure ◽  
Tip Clearance ◽  
Design Parameters ◽  
Outer Diameter ◽  
Steam Turbines ◽  
Low Leakage ◽  
The Impact

Self–correcting Compliant Plate Seals are being developed for various turbomachinery sealing applications including gas turbines, steam turbines, aircraft engines and oil & gas compressors. These seals consist of compliant plates attached to a stator in a circumferential fashion around the rotor. The compliant plates have a slot that extends radially inwards from the seal outer diameter, and an intermediate plate extends inwards into this slot from stator. This design is capable of providing passive hydrostatic feedback forces acting on the compliant plates that balance at a small tip–clearance. Due to this self–correcting behavior, this seal is capable of providing high differential pressure capability and low leakage within a limited axial span, and robust non–contact operation even in the presence of large rotor transients. In this paper we have described the testing of Compliant Plate Seals in a static leakage test rig (“shoebox” rig) to study the impact of different design parameters on leakage and vibration. A novel high–speed visualization set–up is described and the high–speed videos demonstrate robust non–contact operation for different assembly clearances, bridge–gaps and bridge–heights, for various differential pressure and pressure ratio conditions. The reported leakage results indicate that the leakage is relatively insensitive to assembly clearances due to the self–correcting behavior.

scholarly journals Contamination of Brush Seals by Oil and Salt and Its Impact on Rubbing and Hysteresis Behaviour

2019 ◽  
Vol 4 (4) ◽  
pp. 40
Author(s):  
Manuel Hildebrandt ◽  
Corina Schwitzke ◽  
Hans-Jörg Bauer
Keyword(s):  
Heat Fluxes ◽  
Total Power ◽  
Steam Turbines ◽  
Power Losses ◽  
Test Rig ◽  
Degree Of Contamination ◽  
Brush Seal ◽  
Steady State Operation ◽  
Brush Seals ◽  
Hysteresis Behaviour

The literature already contains some experimental, analytical and numerical investigations on the rubbing and hysteresis behaviour of brush seals. What the investigations have in common is that they were carried out with new and uncontaminated seals, or that such a condition was assumed. The influence of contamination has not been explicitly investigated yet. Particularly in stationary gas and steam turbines, foreign substances can accumulate on and in the bristle package during steady-state operation. In the case of a rubbing event with a contaminated brush seal, e.g., during shutdown of the machine, the process is not expected to be comparable to that assumed in the presence of a new, uncontaminated seal. The present paper is dedicated to the question of the influence of contamination on the total frictional power loss generated during rubbing and the distribution of heat fluxes in friction contact. For this purpose, rub tests with two seals were carried out on the brush seal test rig of the Institute of Thermal Turbomachinery (ITS) in new conditions. Subsequently, the sealing packages were contaminated with oil or a salt mixture. After the treatment, the rub tests were repeated and compared with the previous tests. In addition, stiffness measurements were used to assess the degree of contamination. A strong influence on the rubbing behaviour by the contamination was detected. Contamination causes the flexibility of the bristle package to be greatly reduced. As a result, especially at the beginning of the first measurements, the total power losses and rotor heat inputs are strongly increased. This flexibility is partly regained in the course of the measurements. As expected, contamination also influences the hysteresis behaviour of the seal. A highly increased leakage rate after rubbing could be observed, because the bristles remained close to their deflected positions. In the case of the salted seal, however, an improvement in the leakage performance could be observed after several repeat tests.

Brush Seals Used in Steam Environments—Chronological Wear Development and the Impact of Different Seal Designs

2015 ◽  
Vol 138 (5) ◽  
Author(s):  
Markus Raben ◽  
Jens Friedrichs ◽  
Thomas Helmis ◽  
Johan Flegler
Keyword(s):  
Wear Behavior ◽  
Test Facility ◽  
Working Fluid ◽  
Attractive Alternative ◽  
Test Duration ◽  
Steam Turbines ◽  
Two Stage ◽  
Frictional Contacts ◽  
Brush Seals ◽  
The Impact

During the last decades, turbo machine efficiency was considerably increased by using more efficient seals. Brush seals, as a compliant contacting filament seal, have become an attractive alternative to conventional labyrinth seals in the field of aircraft engines as well as in stationary gas and steam turbines. The aim of today's research related to brush seals is to understand the characteristics and their connections, in order to be able to make performance predictions, and to ensure the reliability over a defined operating period. The wear behavior is essentially influenced by frictional contacts at the seal-to-rotor interface during operation. For realistic investigations with representative circumferential velocities, the TU Braunschweig, Germany, operates a specially developed steam test rig which enables endurance investigations under varying operating steam conditions up to 50 bar and 450 °C. Wear measurements and the determination of seal performance characteristics, such as blow down and bristle stiffness, are enabled by an additional test facility, using pressurized cold air up to 8 bar as a working fluid. This work presents the chronological wear development on both rotor and seal sides in a steam test lasting 25 days or 11 days, respectively. Interruptions after stationary and transient intervals were made in order to investigate the degree of wear. Two different seal arrangements, a single tandem seal, and a two-stage single seal arrangement, using different seal elements were considered. Besides a continuous wear development, the results clearly show that the abrasive wear of the brush seal and rotor is mainly caused by transient test operations, particularly by enforced contacts during shaft excursions. Despite the increasing wear to the brushes, all seals have shown a functioning radial-adaptive behavior over the whole test duration with a sustained seal performance. Thereby, it could be shown that the two-stage arrangement displays a load shift during transients, leading to a balanced loading and unloading status for the two single brush seals. From load sharing, and in comparison with the wear data of the tandem seal arrangement, it can be derived that the two-stage seal is less prone to wear. However, the tandem seal arrangement, bearing the higher pressure difference within one configuration, shows a superior sealing performance under constant load, i.e., under stationary conditions.

CFD Investigation of Brush Seal Leakage Performance Depending on Geometric Dimensions and Operating Conditions

2015 ◽  
Author(s):  
Yahya Doğu ◽  
Mustafa C. Sertçakan ◽  
Ahmet S. Bahar ◽  
Altuğ Pişkin ◽  
Ercan Arıcan ◽  
...  
Keyword(s):  
Pressure Ratio ◽  
Plate Thickness ◽  
Operating Conditions ◽  
Design Parameters ◽  
Operational Parameters ◽  
Backing Plate ◽  
Brush Seal ◽  
Front Plate ◽  
Brush Seals ◽  
Geometric Variables

Brush seals require custom design and tailoring due to their behavior driven by flow dynamic, which has many interacting design parameters, as well as their location in challenging regions of turbomachinery. Therefore, brush seal technology has not reached a conventional level across the board standard. However, brush seal geometry generally has a somewhat consistent form. Since this consistent form does exist, knowledge of the leakage performance of brush seals depending on specific geometric dimensions and operating conditions is critical and predictable information in the design phase. However, even though there are common facts for some geometric dimensions available to designers, open literature has inadequate quantified information about the effect of brush seal geometric dimensions on leakage. This paper presents a detailed CFD investigation quantifying the leakage values for some geometric variables of common brush seal forms functioning in some operating conditions. Analyzed parameters are grouped as follows; axial dimensions, radial dimensions and operating conditions. The axial dimensions and their ranges are front plate thickness (z1=0.040–0.150in.), distance between front plate and bristle pack (z2=0.010–0.050in.), bristle pack thickness (z3=0.020–0.100in.), and backing plate thickness (z4=0.040–0.150in.). The radial dimensions are backing plate fence height (r1=0.020–0.100in.), front plate fence height (r2=0.060–0.400in.), and bristle free height (r3=0.300–0.500in.). The operating conditions are chosen as clearance (r0=0.000–0.020in.), pressure ratio (Rp=1.5–3.5), and rotor speed (n=0–40krpm). CFD analysis was carried out by employing compressible turbulent flow in 2-D axi-symmetric coordinate system. The bristle pack was treated as a porous medium for which flow resistance coefficients were calibrated by using literature based test data. Selected dimensional and operational parameters for a common brush seal form were investigated, and their effects on leakage performance were quantified. CFD results show that, in terms of leakage, the dominant geometric dimensions were found to be the bristle pack thickness and the backing plate fence height. It is also clear that physical clearance dominates leakage performance, when compared to the effects of other geometric dimensions. The effects of other parameters on brush seal leakage were also analyzed in a comparative manner.

Sign in / Sign up

Export Citation Format

Share Document