scholarly journals Experimental and Statistical Study on Mechanical Characteristics of Geopolymer Concrete

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1651 ◽  
Author(s):  
Yifei Cui ◽  
Kaikai Gao ◽  
Peng Zhang
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Mechanical Characteristics ◽  
Statistical Hypothesis ◽  
Geopolymer Concrete ◽  
Empirical Equations ◽  
Class F Fly Ash ◽  
Class F

This paper studies the statistical correlation in mechanical characteristics of class F fly ash based geopolymer concrete (CFGPC). Experimentally measured values of the compressive strength, elastic modulus and indirect tensile strength of CFGPC specimens made from class F fly ash (CFA) were presented and analyzed. The results were compared with those of corresponding ordinary Portland cement concrete (OPCC) using statistical hypothesis tests. Results illustrated that when possessing similar compressive and tensile strength, the elastic modulus for CFGPC is significantly lower than that of OPCC. The corresponding expressions recommended by standards for the case of OPCC is proved to be inaccurate when applied in the case of CFGPC. Statistical regression was used to identify tendencies and correlations within the mechanical characteristics of CFGPC, as well as the empirical equations for predicting tensile strength and elastic modulus of CFGPC from its compressive strength values. In conclusion, CFGPC and OPCC has significant differences in terms of the correlations between mechanical properties. The empirical equations obtained in this study could provide relatively accurate predictions on the mechanical behavior of CFGPC.

scholarly journals The Effects of Water to Solid Ratio, Activator to Binder Ratio, and Lime Proportion on the Compressive Strength of Ambient-Cured Geopolymer Concrete

2019 ◽  
Vol 5 (2) ◽  
pp. 161 ◽  
Author(s):  
Andi Arham Adam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide Solution ◽  
Geopolymer Concrete ◽  
Solid Ratio ◽  
Slaked Lime ◽  
Binder Ratio ◽  
Class F Fly Ash ◽  
Good Workability ◽  
Class F

Low calcium fly ash based Geopolymer has been proven to be one of the potential alternatives substitutes to Portland Cement not only due to its high resistance to chemical attack but also because of the vast availability of class F fly ash for raw materials. However, one of the limitations of geopolymer as the alternative binders in concrete is that the strength develops slowly under ambient condition. This paper presented the investigation of water to solid ratio, activator to binder ratio, and lime proportion on the compressive strength of ambient-cured geopolymer concrete. To develop sufficient strength at an early age, class F fly ash and slaked lime (Ca (OH)2) were used as the binder with the proportion of lime to binder of 4%, 5%, 6%, and 7%. The blended binder was activated by sodium silicate and sodium hydroxide solution with the variation of activator to binder ratio of 0.45, 0.5, 0.55, and 0.6.  The water to solid ratio of 0.30, 0.31, 0.32, and 0.33 was chosen to facilitate good workability which was done by adding water to the mix. The compressive strength tests were conducted at 7, 14, and 28 days on the cylindrical concrete specimens with a dimension of 100 mm diameter and 200 mm height. The results show that the activator to binder ratio of 0.50 to 0.55, and the proportion of lime to the binder of 6% to 7% were the optimum range value. It was also found that the lower the water to cement ratio the higher the compressive strength and the water to solid ratio as low as 0.3 produced the highest compressive strength while still maintaining good workability.

Flexural Strength of Low Calcium Class F Fly Ash-Based Geopolymer Concrete in Long Term Performance

2016 ◽  
Vol 841 ◽  
pp. 104-110 ◽  
Author(s):  
Arie Wardhono ◽  
David W. Law ◽  
Thomas C.K. Molyneaux
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Pulse Velocity ◽  
Modulus Of Rupture ◽  
Geopolymer Concrete ◽  
Strength Performance ◽  
Low Calcium ◽  
Class F Fly Ash ◽  
Class F

This paper reports on experimental work that has been undertaken to investigate the flexural strength performance of fly ash-based geopolymer (FG) concrete. The FG concrete was prepared using low calcium class F fly ash with high silicate content. The flexural strength properties of FG were assessed using modulus of rupture test up to the age of 360 days. Compressive strength and Ultrasonic Pulse Velocity (UPV) tests were also performed to corroborate the flexural strength test results. The results showed that the FG concrete demonstrates a comparable compressive strength and velocity to OPC concrete. Hewever, the flexural strength of FG concrete exhibited a better performance compared to that OPC concrete. The measured flexural strength of FG concrete also exhibited a higher value compared to the predicted one using ACI 318M-08 standard. The relationship between flexural strength with compressive strength demonstrated a similarity behavior to that OPC concrete. Thus, it can be concluded that the use of the ACI standard can be applied conservatively to determine the flexural strength of fly ash-based geopolymer concrete.

Compressive Strength Properties of Fly Ash-Based Geopolymer Concrete

2013 ◽  
Vol 741 ◽  
pp. 49-54 ◽  
Author(s):  
Gum Sung Ryu ◽  
Gi Hong Ahn ◽  
Kyung Taek Koh ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Ordinary Portland Cement ◽  
Mechanical Characteristics ◽  
Strength Properties ◽  
Early Age ◽  
Geopolymer Concrete ◽  
Test Results ◽  
Ordinary Concrete

This study intends to investigate experimentally the mechanical characteristics of the compressive strength and elastic modulus of concrete using 3 types of binder that are ordinary Portland cement, fly ash and physically milled fly ash. The test results show that the compressive strength and elastic modulus of the cement-zero concrete reached respectively 30.0 MPa and 19.1 GPa, and indicated that more than 90% of the strength was developed at early age. In addition, a comparison of the geopolymer concrete with ordinary concrete enabled to derive and suggest formulaeexpressing the elastic modulus in function of the compressive strength.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

Freeze-thaw resistance of Class F fly ash-based geopolymer concrete

2019 ◽  
Vol 222 ◽  
pp. 474-483 ◽  
Author(s):  
Renda Zhao ◽  
Yuan Yuan ◽  
Zhengqing Cheng ◽  
Tian Wen ◽  
Jian Li ◽  
...  
Keyword(s):  
Fly Ash ◽  
Geopolymer Concrete ◽  
Freeze Thaw ◽  
Class F Fly Ash ◽  
Class F

scholarly journals Effect of Carboxylic Acid (Benzene Crystallable) in Cement Concrete and Geopolymer Concrete

2020 ◽  
Vol 9 (7) ◽  
pp. 472-475
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Carboxylic Acid ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Split Tensile Strength ◽  
Sealing Capacity ◽  
Time Period

The present study appraises the recitals of carboxylic acid- based admixture to increase concrete water tightness and self-sealing capacity of the cement and geopolymer concrete. Outcomes of the previous studies in particular, adding 1% by cement mass of the carboxylic polymer reasons for reduction in the water dispersion under pressure of 7-day wet cured concrete by 50% associated to that of the conforming reference concrete. At 7 days, M4 mix compressive strength is about 43.5% less than M3 mix. The compressive strength of M4 increases and is about 37.6% less than M3 mix at 28 days of curing. At 7 days, M4 mix split tensile strength is about 17.5% less than M3 mix (cement concrete with 0.45 w/c ratio). The split tensile strength of M4 declines and is about 42.3% less than M3 mix at 28 days of curing. The strength of the geopolymer concrete tends to increase as the time period increases due to the presence of fly ash in it. So it is expected that geopolymer concrete will give more strength than cement concrete in long term with the presence of carboxylic acid

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

scholarly journals Strength and abrasion performance of recycled aggregate based geopolymer concrete

2021 ◽  
Author(s):  
Asfaw Mekonnen LAKEW ◽  
Mukhallad M. AL-MASHHADANI ◽  
Orhan CANPOLAT
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Partial Replacement ◽  
Geopolymer Concrete ◽  
Recycled Coarse Aggregate ◽  
One Year

This experimental work evaluated geopolymer concrete containing fly ash and slag by partial replacement of natural coarse aggregate (NCA) with recycled coarse aggregate (RCA) to manufacture environmental-friendly concrete. The proportion of recycled aggregates considered consists of 10%, 20%, 30%, and 40% of the total coarse aggregate amount. Also, a steel fiber ratio of 0.3% was utilized. The mechanical properties and abrasion resistance of fly ash/slag-based geopolymer concrete were then assessed. Majorly, the mechanical strength of the concrete samples decreased by the increase of RCA content. The geopolymer concrete with 40% RCA gave 28.3% lesser compressive strength and 24% lower splitting tensile strength than NCA concrete at one year. Also, the flexural strength of concrete specimens was reduced by 35% (from 5.34MPa to 3.5MPa) with the incorporation of 40% RCA. The incorporation of 30% RCA caused 23% and 22.6% reduction in compressive strength at 56 days and one year, respectively. The flexural and splitting tensile strength of the specimens was not significantly reduced (less than 10%) with the inclusion of a recycled coarse aggregate ratio of up to 30%. Furthermore, the abrasion wear thickness of every concrete sample was less than 1mm. RCA inclusion of 20% produced either insignificant reduction or better strength results compared to reference mixtures. As a result, it was considered that the combination of 0.3% steel fiber and 20% recycled coarse aggregate in fly ash/slag-based geopolymer concrete leads to an eco-friendly concrete mix with acceptable short and long-term engineering properties that would lead to sustainability in concrete production and utilization sector.

Sign in / Sign up

Export Citation Format

Share Document