scholarly journals Separation of Water/Oil Emulsions by an Electrospun Copolyamide Mat Covered with a 2D Ti3C2Tx MXene

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3171
Author(s):  
AbdolAli Moghaddasi ◽  
Patrik Sobolčiak ◽  
Anton Popelka ◽  
Igor Krupa
Keyword(s):  
Contact Angle ◽  
Vegetable Oil ◽  
Separation Efficiency ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements ◽  
Oil Emulsions ◽  
Uv Transmittance ◽  
Stock Solutions

Purpose: Copolyamide 6,10 (coPA) electrospun mats were covered with multilayered (ML) and single-layered (SL) MXene (Ti3C2Tx) as a membrane for the separation of water/vegetable oil emulsions. Methods: Prepared membranes were characterized by atomic force microscopy (AFM), profilometry, the contact angle measurements of various liquids in air, and the underwater contact angle of vegetable oil. The separation efficiency was evaluated by measuring the UV transmittance of stock solutions compared to the UV transmittance of the filtrate. Results: The MXene coating onto coPA mats led to changes in the permeability, hydrophilicity, and roughness of the membranes and enhanced the separation efficiency of the water/vegetable oil emulsions containing 10, 100, and 1000 ppm of sunflower vegetable oil. It was found that membranes were highly oleophobic (>124°) under water, unlike in air, where the membranes showed high oleophobicity (<5°). The separation efficiency of water/oil emulsions for both types of covered membranes reached over 99%, with a surface coverage of 3.2 mg/cm2 Ti3C2Tx (for ML-Ti3C2Tx) and 2.9 mg/cm2 (for SL-Ti3C2Tx). Conclusions: The separation efficiency was greater than 98% for membranes covered with 2.65 mg/cm2 of ML-Ti3C2Tx, whereas the separation efficiency for membranes containing 1.89 and 0.77 mg/cm2 was less than 90% for all studied emulsion concentrations.

Biopolymer Blends as Potential Biomaterials and Cosmetic Materials

2013 ◽  
Vol 583 ◽  
pp. 95-100 ◽  
Author(s):  
Alina Sionkowska ◽  
Katarzyna Lewandowska ◽  
A. Planecka ◽  
P. Szarszewska ◽  
K. Krasinska ◽  
...  
Keyword(s):  
Contact Angle ◽  
Free Energy ◽  
Surface Free Energy ◽  
Silk Fibroin ◽  
High Surface ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Atomic Force ◽  
Polymeric Blends ◽  
Contact Angle Measurements

Blends of two polymer, namely chitosan with silk fibroin or partially hydrolysed polyacrylamide (HPAM) were prepared. The surface properties of chitosan/silk fibroin and chitosan/HPAM blended films were investigated using the technique of Atomic Force Microscopy (AFM) and by means of contact angle measurements allowing the calculation of surface free energy. Measurements of the contact angle for diiodomethane (D), and glycerol (G) on the surface of chitosan films and chitosan/silk fibroin films were made and surface free energy was calculated. It was found that chitosan/silk fibroin blend surface is enriched in high surface energy component i.e. silk fibroin. The surface roughness of chitosan, silk fibroin, HPAM, chitosan/silk fibroin and chitosan/HPAM blended films differs with the composition of the blend. Film-forming polymeric blends can be potentially used as biomaterials and cosmetic materials.

scholarly journals Nanomechanical characterisation of a water-repelling terpolymer coating of cellulosic fibres

Cellulose ◽  
2021 ◽  
Author(s):  
Julia Auernhammer ◽  
Alena K. Bell ◽  
Marcus Schulze ◽  
Yue Du ◽  
Lukas Stühn ◽  
...  
Keyword(s):  
Contact Angle ◽  
Raman Spectroscopy ◽  
Atomic Force Microscopy ◽  
Water Uptake ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements ◽  
Cellulosic Fibres ◽  
Scanning Electron

Abstract Polymer coatings on cellulosic fibres are widely used to enhance the natural fibre properties by improving, for example, the hydrophobicity and wet strength. Here, we investigate the effects of a terpolymer P(S-co-MABP-co-PyMA) coating on cotton linters and eucalyptus fibres to improve the resistance of cellulose fibres against wetness. Coated and uncoated fibres were characterised by using scanning electron microscopy, contact angle measurements, Raman spectroscopy and atomic force microscopy with the objective of correlating macroscopic properties such as the hydrophobicity of the fleece with microscopic properties such as the coating distribution and local nanomechanics. The scanning electron and fluorescence microscopy results revealed the distribution of the coating on the paper fleeces and fibres. Contact angle measurements proved the hydrophobic character of the coated fleece, which was also confirmed by Raman spectroscopy measurements that investigated the water uptake in single fibres. The water uptake also induced a change in the local mechanical properties, as measured by atomic force microscopy. These results verify the basic functionality of the hydrophobic coating on fibres and paper fleeces but call into question the homogeneity of the coating. Graphic abstract

scholarly journals Adsorption Mechanism of Pb2+ Activator for the Flotation of Rutile

Minerals ◽  
2018 ◽  
Vol 8 (7) ◽  
pp. 266 ◽  
Author(s):  
Wei Xiao ◽  
Hongbo Zhao ◽  
Wenqing Qin ◽  
Guanzhou Qiu ◽  
Jun Wang
Keyword(s):  
Contact Angle ◽  
Single Molecule ◽  
Adsorption Mechanism ◽  
Activation Process ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements ◽  
Molecular Associates ◽  
Hydroxyl Compounds

In general, the flotation of minerals containing titanium needs to be activated by metal ions due to a lack of activating sites on their surface. However, the activating process is indirectly inferred due to the lack of direct experimental observation. In this study, atomic force microscopy (AFM) was used to observe the activation process. The results revealed that the hydroxyl compounds of Pb2+ ions were adsorbed on the rutile surface in the form of multiple molecular associates, rather than through single molecule adsorption. Styryl phosphoric acid (SPA) could largely be adsorbed on the activated rutile surface with a single and double layer rather than on the un-activated rutile surface. The results of contact angle measurements also revealed that the hydrophobicity of the activated rutile surface was significantly greater than that of the un-activated rutile surface after SPA was adsorbed. This study will be helpful to understanding the activating process from the microscale.

Characterization of 3C-SiC (100) as a platform for detecting the onset of acute myocardial infarction (AMI)

2012 ◽  
Vol 1433 ◽  
Author(s):  
Alexandra Oliveros ◽  
Anthony Guiseppi-Elie ◽  
Mark Jaroszeski ◽  
Stephen E. Saddow
Keyword(s):  
Myocardial Infarction ◽  
Acute Myocardial Infarction ◽  
Contact Angle ◽  
Layer Formation ◽  
Water Contact ◽  
Force Microscopy ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements

ABSTRACTIn this work we describe the characterization of anti-myoglobin immobilization on 3C-SiC (100) by means of surface modification with 3-aminopropyltriethoxysilane (APTES). Surface water contact angle measurements were used to compare the wettability of 3C-SiC (100) before (16 ±3°) and after APTES layer formation (61 ±1°). Atomic force microscopy (AFM) was used to confirm the homogenous formation of APTES and anti-myoglobin immobilization with EDC-sulfo NHS coupling. For the APTES surfaces no significant change in the surface roughness was obtained whereas with anti-myoglobin surfaces, particles on the order of ∼60 nm in diameter with a globular shape were observed.

Sign in / Sign up

Export Citation Format

Share Document